• Journal of Mechanical Science and Technology
• /
• v.17 no.10
• /
• pp.1520-1532
• /
• 2003

An experiment was performed to obtain the local heat transfer coefficient and Nusselt number in a circular duct with a 180$^{\circ}$ bend for Re=6 x 10$^4$, 8 x 10$^4$ and 1 x 10$\^$5/ under swirling flow and non-swirling flow conditions. The test tube with a circular section was made from stainless steel having a curvature ration of 9.4. Current heat flux of 5.11 kW/㎡ was applied to the test tube by electrical power and the swirling motion of air was produced by a tangential inlet to the pipe axis at 180$^{\circ}$. Measurements of local wall temperatures and the bulk mean temperatures of air were made at four circumferential positions at 16 stations. The wall temperatures showed a reduced distribution curve at the bend for the non-swirling flow, but this effect did not appear for the swirling flow. The Nusselt number distributions for the swirling flow, which was calculated from the measured wall and the bulk temperatures, were higher than that of the non-swirling flow. The average Nusselt number of the swirling flow increased by about 90-100%, compared to that of the non-swirling flow. The Nu/Nu$\_$DB/ values at the 90$^{\circ}$ station for non-swirling flow and swirling flow were approximately 2.5 and 4.8 at Re=6x10$^4$ respectively. The values agree well with Said's results for non-swirling flow.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.2860-2870
• /
• 1994

When crack are detected in aged turbine rotors of power plants, information on fracture resistance of the aged material at operating temperature is needed for determination of critical loading condition and residual life of the turbine. In this study, fracture toughness (J$_lc$) and tearing modulus(T$_mat$) of virgin and thermally degraded 1Cr-1Mo-0.25V steel, which is one of the most widely used rotor steels, were measured at 538.deg. C according to ASTM E813 and ASTM E1152, respectively. Five kinds of specimen with different degradation levels were prepared by isothermal aging heat treatment at $630^{\circ}C.$ It was observed that J$_lc$ and T$_mat$ value decreased as the degradation level increased. Analysis of microstructures using a scanning electron microscope showed that the decrement of J$_lc$ is related to segregation of impurities at grain boundaries. It was also verified that the DC electric potential drop method is accurate and reliable for crack length monitoring at elevated temperature.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.2
• /
• pp.43-52
• /
• 2017

Heat treatment condition for dissolution of the M23C6 carbides in 2.25Cr-1Mo-V-Ti material for thermal power plant tube was investigated using a dilatometer method. 2.25Cr-1Mo-V-Ti material was heat-treated at $900{\sim}1,100^{\circ}C$ for 0, 10, 30 min to find the proper dissolution condition of M23C6 carbides. The phase identification and volume fraction of the carbide were measured by using OM, SEM, EBSD and TEM analysis. Optimal heat treatment condition of M23C6 carbide dissolution was selected by predicting dissolution temperature of carbide using Bs points appeared at dilatometer curve. Experimental results showed that the conditions of carbide dissolution was 900, 1,000, $1,100^{\circ}C$ for 30 min. Eventually, the optimal heat treatment condition for dissolution was 30 min at $1,000^{\circ}C$ considering the minimum coarsening of Austenite grain size.

• Korean Journal of Applied Biomechanics
• /
• v.14 no.2
• /
• pp.139-152
• /
• 2004

Two subjects, an expert and a novice, were carefully selected based upon their foot speed. Three dimensional videography was used in the assessment of roundhouse kicking of the Tae-kwon-Do. The local reference frames were imbedded at the trunk, pelvis, thigh and shank. Anatomical angular displacement at the joints were measured by projecting the upper segment's local axes to the lower segment's local reference planes. The local axes again projected to the global reference frames and absolved each segment's movement. The peaks of the anatomical angular displacement curve assessed as the countermovements and the angular movements of the segments in the global space absolved in light of the occurrence of the countermovements. The expert showed larger and more countermovements than the novice at the all segments. The counterrnovement occured more clearly at the trunk than the hip and knee joint and during the preparative movement phase. These countermovements occurrence were due to either by turning upper or lower segments and controlled by the turning direction and sequence of the two nearby segments. It was revealed that the countermovements of the trunk during the preparative movement phase was the important factor of the power kicking.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.781-784
• /
• 2002

Adhesion phenomenon is more significant for smaller objects, because adhesional force is proportional to size of the objects while gravitational force is proportional to the third power of it. For the purpose of microassembly, theoretical understanding is required for the Adhesion phenomenon. Authors have developed a force measurement system in an ultra-high vacuum chamber of Auger electron spectroscopy. The force between arbitrary combination of materials can be measured at a pressure less than 100 nPa after and before Ar ion sputtering and chemical analysis for several atomic layers of the surface. The results are successfully interpreted with a theory of contact mechanics. Since surface energy is quite important in the interpretation, electronic theory is used to evaluate the surface energy. In the manipulation of small objects, the adhesional force is always attractive. Repulsive force is essential for the manipulation. It can be generated by Coulomb interaction. The voltage required for detachment is theoretically analyzed and the effect of boundary conditions on the detachment is obtained. The possibility and limitations of micro-manipulation using both the adhesion phenomenon and Coulomb interaction are theoretically clarified. Its applicability to nano-technology is found to be expected.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.8 s.173
• /
• pp.192-198
• /
• 2005

In this paper, we propose a new training system for the improvement of equilibrium sense using unstable platform. The equilibrium sense, which provides orientation with respect to gravity, is important to integrate the vision, somatosensory and vestibular function to maintain the equilibrium sense of the human body. In order to improve the equilibrium sense, we developed the software program such as a block game, pingpong game using Visual C++. These training system for the equilibrium sense consists of unstable platform, computer interface and software program. The unstable platform was a simple structure of elliptical-type which included tilt sensor, wireless RF module and the device of power supply. To evaluate the effect of balance training, we measured and evaluated the parameters as the moving time to the target, duration to maintain cursor in the target of screen and the error between sine curve and acquired data. As a results, the moving time to the target and duration to maintain cursor in the target was improved through the repeating training of equilibrium sense. It was concluded that this system was reliable in the evaluation of equilibrium sense. This system might be applied to clinical use as an effective balance training system.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.1 s.14
• /
• pp.13-16
• /
• 2006

AIN thin films were prepared on amorphous glass and $SiO_2(1{\mu}m)/Si(100)$ substrate by the facing targets sputtering (FTS) apparatus, which can provide high density plasma, a high deposition rate at a low working gas pressure. The AIN thin films were deposited at a different nitrogen gas flow rate ($1.0{\sim}0.3$) and other sputtering parameters were fixed such as sputtering power of 200w, working pressures of 1mTorr and AIN thin film thickness of 800 nm, respectively. The thickness and crystallographic characteristics of AIN thin films as a function of $N_2$ gas flow rate $[N_2/(N_2+Ar)]$ were measured by $\alpha$-step and an X-ray diffraction (XRD) instrument. And the c-axis preferred orientations were evaluated by rocking curve. In the results, we could prepared the AIN thin film with c-axis preferred orientation of about $5^{\circ}$ on substrate temperature R.T. at nitrogen gas flow rate 0.7.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.26 no.5
• /
• pp.368-374
• /
• 2016

This paper presents an experimental study on an electrical circuit model of the TiO2-based nano-wired memristor device for neuromophic applications. The electrical circuit equivalent model of the proposed memristor device consists of several electronics components and some passive devices including operational amplifiers, multipliers, resistors and capacitors. In order to verify the proposed design, both of simulation (using PSPICE) as well as hardware implementation were performed for the analysis of the memristor circuit with time waveforms, frequency spectra, I-V curves and power curves. The gained results from the measured data showed a good agreement with the simulation result that confirm the proposed idea.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.176-179
• /
• 2009

The performance of direct methanol fuel cells is affected by operating conditions such as, methanol feeding temperatures, methanol concentrations, and methanol flow rates during the operation in different environmental conditions. In this study, effects of the environmental temperature on performance of direct methanol fuel cells have been investigated in order to test a applicability of direct methanol fuel cell to the vehicle. The environmental temperature (ET) was varied from $-20^{\circ}C$ to $+30^{\circ}C$. The inside fuel cell temperature (CT) during test at various operating conditions was monitored and the performance of fuel cell was measured in the I-V polarization curve. With increasing the ET, the performance of the fuel cell was significantly improved and the CT also almost linearly increased. However, at below $0^{\circ}C$ ET, the DMFC showed very poor performance and needed to control CT or methanol feeding temperature (MFT), methanol flow rate(MFR) to obtain enough power of the vehicle.

• The Korean Journal of Food And Nutrition
• /
• v.30 no.4
• /
• pp.689-695
• /
• 2017

Ohmic heating is an internal heating method based on the principle that when an electrical current passes through food, electric resistance heat is uniformly generated internally by food resistance. Previous studies indicate that the thermal properties, external structure, internal structure, and swelling power of ohmic heat treated starch of various starches, such as potato, wheat, corn, and sweet potato, differed from those of conventional heating at the same temperature. In this study, the pasting property of starch, treated with ohmic and conventional heating, were measured by RVA (Rapid Visco-Analyzer). Our results show that as the ohmic heating temperature increased, the PV (Paste Viscosity) of the starch decreased significantly, and the PT (Pasting Temperature) increased. Changes in PV and PT indicate that the swelling of starch remains unchanged by ohm heating. The HPV (Hot Paste Viscosity), CPV (Cold Paste Viscosity) and SV (Setback Viscosity) of ohmic heated starch also differed from the conventional heated starch. The pasting property is similar to the viscosity curve of common cross-linked modified starch. In this experiment, we further confirm the similarity with modified starch and its usability.