• Current Photovoltaic Research
• /
• 제6권3호
• /
• pp.69-73
• /
• 2018

PV system is consisted with PV module, inverter and BOS(balance of system). To have robustic operation more than 20 years, the expected and guaranteed durability and reliability of products should be met. Almost components of PV system are qualified through IEC standards at test laboratory. But the qualification certificate of product does not ensure long-term nondefective operation. PV module's expected life time is nowadays more than 20 years and annual maximum power degradation ratio would be less than -1%. But the power degradation ratio is basically based on real data more than several years' record. Developing test method for ensuring annual maximum power degradation ratio is very need because there are many new products every month with new materials. In this paper, we have suggested new test method under continuous artificial light irradiation test condition for analyze expected maximum power drop ratio.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권4호
• /
• pp.164-169
• /
• 2001

This paper deals with comparison of characteristics of continuous-sheet type low-Tc superconducting (LTS) power supply and discrete-sheet type LTS power supply. These characteristics have been analyzed through experiments. These power supplies consist of two exciters, a rotor, a stator, and a LTS load. A continuous-sheet type has a single continuous niobium (Nb) sheet attached to the inner surface of on the stator. In the case of discrete-sheet type, four separated Nb sheets are used. this experiment is using 1.81 mH LTS magnet load and maximum 30 A dc exciter current. A discrete-sheet type is expected to produce much better pumping rate than a continuous-sheet type. The experimental observations have been compared with the theoretical predictions. In this experiment, the maximum pumping-current has reached about 926 A.

• 수산해양기술연구
• /
• 제41권3호
• /
• pp.227-233
• /
• 2005

In order to estimate the effective horse power(EHP) in towing net of a bottom trawl ship, the ship's resistance was calculated by using a series data of Yamagata and Wigley formula. Also the effective horse power for a ship(EHPs) was estimated versus the ship speed in sailing and the propulsive efficiency was calculated with the brake horse power and the effective horse power. Then the effective horse power for a ship and a trawl net were estimated in the application of the propulsive efficiency in towing net. The total effective horse power($EHP_T$) was average 187.6kW and the effective horse power for a 1.awl net($EHP_n$) was average 176.7kW at a smooth sea state in towing net. The ratio of $EHP_n$ to $EHP_T$ was about 94.0% and the value was higher slightly than was already informed at a smooth sea state. The power for keeping up a townet speed was required more about 20% of a maximum continuous power at a rather rough sea state than a smooth sea state. In the future, if the residual resistance is considered with a sea state, $EHP_n$ will be estimated more correctly Also the data of EHP estimated by this method will be used as the basic data to design a trawl net.

• 한국생산제조학회지
• /
• 제4권2호
• /
• pp.25-30
• /
• 1995

The shifting and steering performance of the tracked vehicle with the hydromechanical continuous variable transmission is analyzed. The simulation results are closely similar to both the vehicle test result, As a result of hydromechanical transmission simulation, power circulation in 2nd and 3rd range is maximum 142% And power flow of mechanical part has the relationship with the effeciency of the vehicle and transmission.

• Current Optics and Photonics
• /
• 제1권5호
• /
• pp.525-528
• /
• 2017

High-energy, high-power, quasi-continuous wave (QCW) operation of double-clad Yb fiber lasers incorporating an incoherent signal combiner is reported. We constructed four efficient, high-power Yb fiber lasers, each of which produced rectangular pulses at 1080 nm with a pulse energy greater than 15 J, and a pulse duration of 10 ms at a repetition rate of 10 Hz, corresponding to an average power of over 150 W and a peak power of over 1.5 kW for ~200 W of incident pump power at 915 nm. These laser outputs were combined by a homemade incoherent fiber signal combiner with low loss, yielding a maximum peak power of ~6.0 kW in a beam with $M^2{\approx}12.5$. The detailed laser characteristics and prospects for further power scaling in QCW operation are discussed.

• Current Optics and Photonics
• /
• 제5권3호
• /
• pp.306-310
• /
• 2021

A 200-W continuous-wave thulium-doped all-fiber laser at 2050 nm was developed with a master oscillator power amplifier configuration. For the master oscillator, a single-mode thulium-doped fiber laser was built with fiber Bragg gratings. The operating power of the oscillator was 10.1 W at a pump power of 20.9 W, and the slope efficiency was measured to be 53.0%. All emitted wavelengths of the oscillator were located between 2049.2 nm and 2049.9 nm, and no other peaks in different wavelength ranges were observed. The maximum output power of the final amplified beam was 204.6 W at a pump power of 350.4 W. The slope efficiency of the amplifier was measured to be 58.4%.

• 한국물환경학회지
• /
• 제25권1호
• /
• pp.159-166
• /
• 2009

This study has been attempted to generate electricity, while simultaneously treating artificial organic wastewater using both batch and continuous microbial fuel cells (MFCs). In the batch MFC, current-voltage curve showed an onset potential of -0.69 V vs. Ag/AgCl. The potential range between this potential and 0 potential displayed an available voltage for an automatic production of electric energy and glucose, which was oxidized and treated at the same time. The 486 mg/L glucose solution showed the maximum power of $30mW/m^2$ and the maximum current density of $75mA/m^2$ shown in the power curve. As a result, discharging of the cell containing COD 423 mg/L at the constant current density of $60mA/m^2$ showed a continuous electricity generation for about 22 hours that dropped rapidly due to dissipating of organic material. Total electric energy production was 18.0 Wh. While discharging, the pH change was low and dropped from pH 6.53 to 6.20 then increased to 6.47, then stabilized at this charge. The COD treatment efficiency was found to be 72%. In the continuous MFC, COD removal tends to increase as the hydraulic retention time is increased. At one day of hydraulic retention time as the maximum value reaches the COD removal efficiency, power production rate and power production rate per COD removal that were obtained were 68.8%, $14mW/m^2$, and $20.8mW/m^2/g$ CODrm, respectively. In the continuous MFC, the power production rate per COD removal increases as the hydraulic retention time is increased and decreases as the organic loading rate is increased. At the values lower than an organic loading rate of $1kgCOD/m^3/d$, the values higher than about $18.1mW/m^2/g$ CODrm could be obtained.

• 상하수도학회지
• /
• 제20권2호
• /
• pp.225-234
• /
• 2006

Characteristics of electricity production from major fermentation products (acetate, propionate and butyrate) were evaluated in a microbial fuel cell (MFC). For each substrate, batch and continuous experiments were performed. The batch test result indicated that coulombic efficiency depended on the resistance connected in MFC circuit. With acetate, coulombic efficiency were 87% at $20{\Omega}$, but decreaced to 45% at$220{\Omega}$. In continuous tests, maximum power densities obtained was 220 Q with acetate. The maximum power densities of butyrate, acetate and propionate were 6.8, 6.1, and $5.2mW/m^2$, respectively. Propionate and butyrate were converted into acetate producing high currents. $H_2$ produced during butyrate and propionate probably used to produce electricity. In conclusion, butyrate conversion into acetate was faster than that of propionate with higher electricity production. If the production of propionate is inhibited during fermentation, anaerobically fermented liguor may be effectively applied for MFC.

• Current Optics and Photonics
• /
• 제2권4호
• /
• pp.356-360
• /
• 2018

We demonstrate continuous-wave operation of an all-fiber thulium-holmium codoped laser operating at a wavelength of 1706.3 nm. To realize laser operation in the short-wavelength region of the emission-band edge of thulium in silica fiber, we employ fiber Bragg gratings having resonant reflection at a wavelength around 1700 nm as a wavelength-selective mirror in an all-fiber cavity scheme. We first examine the performance of the laser by adjusting the central wavelength of the in-band pump source. Although a pump source possessing a longer wavelength is observed to provide reduced laser threshold power and increased slope efficiency, because of the characteristics of spectral response in the gain fiber, we find that the optimal pump wavelength is 1565 nm to obtain maximum laser output power for a given system. We further explore the properties of the laser by varying the fiber gain length from 1 m to 1.4 m, for the purpose of power scaling. It is revealed that the laser shows optimal performance in terms of output power and slope efficiency at a gain length of 1.3 m, where we obtain a maximum output power of 249 mW for an applied pump power of 2.1 W. A maximum slope efficiency is also estimated to be 23% under these conditions.

• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.29-34
• /
• 2014

Cooling the in-wheel motor in electric vehicles is critical to its performance and durability. In this study, thermal flow analysis was conducted by evaluating the thermal performance of two conventional cooling models for in-wheel motors under the continuous rating base speed condition. For conventional model #1, in which cooling oil was stagnant in the lower end of the motor, the maximum temperature of the coil was $221.7^{\circ}C$; for conventional model #2, in which cooling oil was circulated through the exit and entrance of the housing and jig, the maximum temperature of the coil was $155.4^{\circ}C$. Therefore, both models proved unsuitable for in-wheel motors since the motor control specifications limited the maximum temperature to $150^{\circ}C$.