• Magazine of the Korean Society of Agricultural Engineers
• /
• v.12 no.1
• /
• pp.1854-1860
• /
• 1970

Results of this study on the influence of percent passing of No. 200 sieve on soil compaction are as follows; 1. The higher maximum dry density of soil is, the lower optimum moisture content is. Maximum dry density is highest value and optimum moisture content is the lowest value in twocases that percents of No. 200 sieve are 30% in soils of which percents retained on No. 10 sieve are 5% and 10% respectively. 2. Maximum dry density increases according as uniformity coefficient increase. Maximum dry density is the highest when uniformity coefficient is approximately 300 in soil of which maximum diameter is 4.76mm. 3. Maximum dry density has a tendency to become large according as value of Cu Caincrease. Correlation between maximum dry density and $Log_{10}$(CuCa) shows straight line. 4. Maximum dry density increases according as n increase and reaches the peak when n equal 0.35 in condition that the index of talbot formula n is less than 0.35 in soil of which maximum diameter is 4.76mm. 5. Maximum dry density has a tendency to increase according as value of Cg $(Cg=\frac{P_{50}^2}{P_{10}{\times}{P_{200}}$) decrease.

• The Journal of Korean Academy of Prosthodontics
• /
• v.11 no.1
• /
• pp.9-14
• /
• 1971

The author measured the maximum interincisal distance by means of the sliding caliper. The subjects measured here were 149 healthy Korean males and 229 females, ranging from 15 to 49 years old, with normal occlusion. The results were as follows; 1. The mean value of maximum interincisal distance was $50.03{\pm}0.22mm$. in male and $45.18{\pm}0.14mm$. in female. 2. There was a significant difference in the mean value between male female. 3. The interincisal distances in maximum opening were slightly larger in male than female. 4. There was no significant difference in the mean value between the age groups in Korean adults. But it has been revealed that there was apparent difference in the mean value between 15~19 years and 20~29 years old, in female. 5. It has been appeared that maximum interincisal distance in male was 69mm, minimum 37mm., and maximum interincisal distance in female was 58mm. minimum. 30mm.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.3
• /
• pp.1-5
• /
• 2019

The superconductor stability theories are consistently described by the integral formula. If the defined stability function is a simple decreasing function, it becomes a cryogenic stability condition. If the stability function has a maximum value and a minimum value, and the maximum value is less than 0, then it is a cold-end recovery condition. If the maximum value is more than 0, it can be shown that the unstable equilibrium temperature, that is, the MPZ (minimum propagation zone) temperature distribution can exist. The MPZ region is divided into two regions according to the current ratio. At the low current ratio, the maximum dimensionless temperature is greater than 1, and at the relatively high current ratio, the maximum dimensionless temperature is less than 1. In order to predict the minimum quench energy, the dimensionless energy was obtained for the MPZ temperature distribution. In particular, it was shown that the dimensionless energy can be obtained even when the MPZ maximum temperature is 1 or more.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.1
• /
• pp.6-9
• /
• 2011

Step feed process was analyzed stoichiometrically for the optimal operation conditions in this study. In case of optimal operation conditions, minimum R (sludge recycling) value, r (internal recycling ratio) value, and n (influent allocation ratio) value for the step feed process to acquire the maximum TN removal efficiency were identified by theoretical analysis. Maximum TN removal efficiency, based on stoichiometric reaction, can be obtained by controlling n value for the step feed process.

• Proceedings of the Society of Korea Industrial and System Engineering Conference
• /
• 2002.05a
• /
• pp.19-24
• /
• 2002

The result of management profits create to manufacturing activity. The gross sale profits must be maximum thraw spend of economic value. The profit maximum have to management based key value driver of manufacturing activity. The important factors of the study model are manufacturing value driver(MVD) and manufacturing value added(MVA). We show necessity of management based value by means of a case study.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.496-499
• /
• 2006

The solar cells should be operated at the maximum power point because its output characteristics are greatly fluctuate on the variations of insolation, temperature and loads. To obtain maximum power from solar cell, photovoltaic system cell power system usually requires maximum power point tracking controller. This paper propose Maximum power point tracking method using zero slope of differential value of maximum power. The power compare method traces to maximum power point rapidly but oscillate on the maximum power point largely, when quantity insolation variation is big. The power compare method is traces to maximum power point slowly but oscillate maximum point on the maximum power point smally, when quantity insolation variation is small. To solve two problem of the power compare method, designed zero slope of differential value of maximum power.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.4
• /
• pp.232-237
• /
• 2013

This paper presents image database retrieval based on maximum color occurrenceusing Hue, Saturation and Value (HSV) color space. Our system is based on color segmentation. We dividedthe image into n number of areas based on different selected ranges of hue and value, then each area is partitioned into m number of segments based on the number of pixels it contains, after this we calculated the maximumcolor occurrence in each segment and used its HSV value. This is used as a feature vector.

• Journal of the Korean Data and Information Science Society
• /
• v.18 no.3
• /
• pp.817-826
• /
• 2007

In this paper, we derive the approximate maximum likelihood estimators of the scale parameter and the location parameter in a generalized extreme value distribution under multiply Type-II censoring by the approximate maximum likelihood estimation method. We compare the proposed estimators in the sense of the mean squared error for various censored samples.

• Proceedings of the Korean Statistical Society Conference
• /
• 2003.10a
• /
• pp.73-78
• /
• 2003

This presentation derives a distribution function of the terminal value and running maximum of two-dimensional Brownian motion {X(t) = (X$_1$(t), X$_2$(T))', t > 0}. One random variable of the joint distribution is the terminal time value of the Brownian motion {X$_1$(t), t > 0}. The other random variable is the partial-time running maximum of the Brownian motion {X$_2$(t), t > 0}. With this distribution function, this presentation also derives an explicit pricing formula for a barrier option whose monitoring period of the option starts at an arbitrary date and ends at another arbitrary date before maturity.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.5
• /
• pp.1419-1425
• /
• 2000

When we predict of software reliability, we can't know the testing stopping time and how many faults be residues in software the (the maximum value of data) during these software testing process, therefore we assume the maximum value and the training result can be inaccuracy. In this paper, we present neural network approach for software reliability prediction with unnormalized (actual or original collected) data. This approach is not consider the maximum value of data and possible use the network without normalizing but the predictive accuracy is better. Also, the unnormalized method shows better predictive accuracy than the normalized method given by maximum value. Therefore, we can make the best use of this model in software reliability prediction using unnormalized data.