• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.1
• /
• pp.134-145
• /
• 2021

It is common to optimize the propulsion control system through a so-called tuning process that modifies the parameter values of the propulsion control software during a ship commissioning. However, during this process, if the error of the initial setting value is large, the tuning time may take too long, or the propulsion equipment can be seriously damaged. Therefore, we conducted research on the design of a propulsion controller that applied a Processor lever controller even for inexperienced people with relatively little experience in tuning propulsion control software to be able to reduce the tuning time while protecting the propulsion system. Through simulation, by comparing the execution result of propulsion control lever commands through the PI controller without applying the Processor lever controller. We analyzed the improvement of the Overshoot and propulsion performance. The simulation results showed that the safety of the propulsion system increased because Overshoot of approximately 9.74%, which occurred when the Processor lever function was not applied.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.6
• /
• pp.606-614
• /
• 2020

The administrative ship, Chuja-ho, is the only mode of transportation between manned islands in the Chuja-do, Jeju. Chuja-ho is a 25-year-old age, which is identified to pass the persisting period (25 years) for public ships, and there is an urgent need for a replacement. The residents of the island are also requesting that the new administrative ship be outfitted with medical functions because there is no sea transportation system for medical emergencies in Chuja-do. The purpose of this study is to examine the required functions of a new administrative ship outfitted with medical functions and to suggest a conceptual design. In order to review the necessity of an emergency patient transport system, user requirements were surveyed and analyzed, and the ship's condition assessed by ship experts who carried out an on-site survey and analysis of ship survey data. Thereafter, a conceptual design for a new administrative ship with medical functions was presented. The results of this study can be used during a review of a new budget plan and for basic ship designs during the replacement project by the local government. It is also expected to improve the safety and medical environment of Chuja-do residents.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.667-669
• /
• 2021

Recently, RFID/USN technology has been applied in various fields such as logistics, environment, education, home network, disaster prevention, military, and medical care, but despite the remarkable development of RFID/USN technology, it is difficult to apply it to marine industry due to the characteristics of poor marine environment. Therefore, satellites are mainly used in the marine sector, and existing communication networks are used in the coast, so measures for forming a shelf-only short-range network in the ocean are being considered. In this paper, we consider the use of drones as mobile base stations of USN as a base station role using USN in existing PS-LTE and LTE networks.Since autonomous navigation vessels are aiming for the intelligent system, the number of crew and labor force should be reduced and the function of autonomous network formation in the form of more stable and intelligent ICT convergence technology should be strengthened.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.4
• /
• pp.465-473
• /
• 2021

Since the past, ships have hoisted national flags as a means of indicating their nationality. Both domestically and internationally, laws and conventions related to the nationality and hoisting of the flag have been enacted because it is significant that the nationality of a ship is a matter of the jurisdiction of the ship. Nevertheless, there are differences in domestic and international regulations related to the hoisting of the flag of a ship, and if the flag is not hoisted irrespective of the intention, there may be a difference in interpretation as to whether or not the ship will be regarded unconditionally as a stateless ship. However, there is no disagreement locally or abroad about the necessity of indicating the nationality of ships. Therefore, I would like to propose a method to indicate and confirm the nationality of the ship by using wireless communication equipment with hoisting the flag as the only way to express its nationality, reflecting the situation of the era such as high-speed, larger and unmanned ship. Representatively, the method utilizes the automatic identification system(AIS), which is one of the equipment legally installed in the ship, and includes the ship's nationality in its information. If the nationality information is included in the AIS, nationality can be identified earlier and even from a distance, and there will not be instances of nationality not being identified because the flag is not hoisted or the flag is damaged. In addition, it is expected that the problem of nationality indication can be solved even when vessels are unmanned in future.

• Journal of Korean Port Research
• /
• v.11 no.2
• /
• pp.321-337
• /
• 1997

Rapid change in the technological environment of marine transportation and the development of the ocean shipping industry have fostered a revolution in the port system. This in turn has caused major changes in the function and use of port in Korea. Aside from this. Mokpo Port, however continues to decline, because the existing port facilities and related subsystem are already obsolete with no chance of regaining operational effectiveness and treatment for proper implementation. Although a few studies have been done on the Mokpo Port, has not been found, any reseach for the analytical approach to the transportation system of it. This paper aims to make an extensive analysis of the physical distribution system in Mokpo Port focusing on the coordination of subsystems such as navigational aids system, quay handling and transfer system, storage system and inland transport system. The base of introduced simulation tool here is the queueing theory. The overall findings are as follows; 1. Among those vessels called at Mokpo Port in 1994, the average size of oceangoing vessels is 4,922.1 G/T, and the domestic is 317.8 G/T. The average arrival interval and service time of the domestic vessels are 6.0 hours and 24.1 hours respectively marking the berth occupation rate over 100%. Those for oceangoing vessels are 34.5 hours, 120.0 hours and 37.2%. In order to maintainin the berth occupation rate to 70% the capacity considering the 1994 of domestic piers must be extended to 145% and oceangoing vessels must be increased to 165% year called. 2. The capacity of approaching channel is enough to handle the total traffic volume. 3. Tugs are sufficiently being provided to handle all ships requiring their services 4. The capacity of storage and inland transportation systems are sufficient to handle the throughput and the yard stroage utilization rate of No.1 $\cdots$ No.5 is 4.5% and No.6 1S 30% of 1993's. 5. The utilization rate of LLc(Level Looping Crane) and PNT(PNeumaTic) are 2.7% and 18.8%, respectively. Practical solution and proposal for improvement of Transportation System in Mokpo Port are as follows; 1. To avoid the congestion in domestic pier introduction of a new port operation system is necessary allowing the domestic vessel to use the oceangoing pier. 2. To establish the port management information system to improve the efficiency of port operation. 3. To build a new storage system for high valued cargos including modernization of the present storage and handling system. 4. To insure the safety of navigation in approaching channel, The Vessel Traffic System including separation scheme is introduced. 5. To interest enormously on public relation to ship owner's association, shippers and consignees by showing that they can save cost and ship turnaround time in order to promote the call to Mokpo Port. At last, to be strategically change the function of Mokpo Port to the Leisure, Fishing & Ferry as well as Maritime port.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.4
• /
• pp.412-418
• /
• 2020

Generally, the propeller shaft that constitutes the ship shaft system has different patterns of behavior due to the ef ects of engine power, propeller load and eccentric thrust, which increases the risk of bearing failure by causing local load variations. To prevent this, different studies of the propulsion shaft system have been conducted focused the relative inclination angle and oil film retention between the shaft and the support bearing, mainly with respect to the Rules for the Classification of Steel Ships. However, in order to secure the stability of the propulsion shaft via a more detailed evaluation, it is necessary to consider dynamic conditions, including the transient state due to sudden change in the stern wakefield. In this context, a 50,000 DWT vessel was analyzed using the strain gauge method, and the effects of propeller shaft movement were analyzed on the starboard rudder turn which is a typical transient state during normal continuous rate(NCR) operation in ballast draught condition. Analysis results confirm that the changed propeller eccentric thrust acts as a force that temporarily pushes down the shaft to increase the local load of the stern tube bearing and negatively affects the stability of the shaft system.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.557-565
• /
• 2021

Path-following control is considered as one of the most fundamental skills to realize autonomous navigation of marine vessels in the ocean. This study addresses with the path-following control for a ship in which there are environmental disturbances in the directions of the surge, sway, and yaw motions. The guiding principle and back-stepping method was utilized to solve the ship's tracking problem on the reference path generated by a virtual ship. For path-following control, error dynamics is one of the most important skills, and it extends to the research fields of automatic collision avoidance and automatic berthing control. The algorithms for the guiding principles and error variables have been verified by numerical simulation. As a result, most error variables converged to zero values with the controller except for the yaw angle error. One of the most interesting results is that the tracking errors of path-following control between two ships are smaller than the existing safe passing distances considering interaction forces from near passing ships. Moreover, a trade-off between tracking performance and the ship's safety should be considered for determining the proper control parameters to prevent the destructive failure of actuators such as propellers, fins, and rudders during the path-following of marine vessels.

• Journal of Navigation and Port Research
• /
• v.33 no.1
• /
• pp.35-41
• /
• 2009

A waypoint tracking algorithm(WTA) is designed for Unmanned Surface Vehicle(USV) in which water-jet system is installed for propulsion To control the heading of USV for waypoint tracking, the steering nozzle of water-jet need, to be controlled. Firstly, target heading is calculated by using the position information of waypoints input from the land control center. Secondly, the command for the steering nozzle of water-jet is calculated in real time by using the heading and the rate-of-turn( ROT) from magnetic compass, In this study, in order to consider the drift angle due to external disturbance such as wind and wave, the course of ground( COG) can be used instead of heading at higher speed than a certain value, To test the performance of newly-designed WTA, the tests were carried out in actual sea area near Gwang-an bridge of Busan. In this paper, the sea trial test results from WTA are analyzed and compared with those from manual control and those from commercial controller.

• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.214-220
• /
• 2019

The calibration method of the initial value error obtained in the weight measurement through anchor bolt type strain gauge sensor is proposed. The strain gauge sensor is developed for preventing the overturning of forklift, which is the most frequent type of safety-accident in industry. It was confirmed that the initial value error is caused from the physical and mechanical error of anchor bolt, and the environmental problem. Since the elimination of these causes falls outside the realm of this research, we find out the calibrated values based on all the causes, and we adjust the initial values of analog-to-digital convertor (ADC) module consisted of strain gauge sensor block using the calibrated values. We use the linear interpolation method for our calibration. We confirm that four sensor modules have the different under 5% between the real weight and the measured value in the experiment applied with the calibration of initial values. The low correlation between the real weights and ADC values is also improved through the proposed calibration.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.95-100
• /
• 2021

If we know the location of the hull block and the welding feeder in the shipyard, we can easily obtain the location information of the worker. That data is very useful for implementing a workplace safety monitoring system. However, it is difficult to apply a fixed communication network to the workplace due to the specificity of the hull structure and welding process. In this study, inductive power line communication, which can replace dedicated communication line, was reviewed. A ferrite core was used as an inductive coupler to be installed on the power cable of the welding machine, and a nano-crystalline core was applied as a coupler to be fastened to the support rod of the metal block. In order to visualize the operating principle of the proposed couplers, 3D modeling and finite element analysis were performed with the COMSOL AC/DC module. In the communication performance test using an aluminum profile, when the communication channel was formed by the contact of the welding electrode, the bandwidth was kept above 6 Mbps.