• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.528-537
• /
• 2015

To reuse the waste bone from restaurants or butcher houses, the possibility of using waste bone powder after cooking as a filler for wood adhesives used in manufacturing plywood was investigated. Radiata pine (Pinus radiata D. Don) plywoods were manufactured by using commonly used wood adhesives such as urea-melamine formaldehyde (UMF) resin, urea-formaldehyde (UF) resin, and phenol-formaldehyde (PF) resin and the prepared fillers from cattle bone powder, pig bone powder, and seashell powder. Plywood fabricated by using cattle bone powder, pig bone powder, and seashell powder showed weaker performance in dry and wet glue-joint shear strength and wood failure than those of the plywood with wheat flour. The result showed that it was hard to use only bone powder for the replacement of wheat flour. However, the filler mixed with wheat flour and bone powders showed equivalent dry bonding strength and better water resistance than the wheat flour, indicating that bone powders mixed with wheat flour might be used for the manufacture of plywood. When bone powders were mixed with wheat flour as adhesive fillers the shell powder showed the lowest bonding properties and there was no big difference between the cattle bone powder and the pig bone powder.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.62 no.5
• /
• pp.39-46
• /
• 2020

This study evaluated the nitrogen oxide (NO_x) removal efficiency by air purification concrete blocks with titanium dioxide (TiO₂). The concrete in the mixtures had a 30% water:cement ratio, to which TiO₂ was added at 0%, 5%, and 10% of cement weight. The compressive strength reduction rate and removal efficiency of NO_x were investigated. The result of the compressive strength test in the study indicated that addition rate of TiO₂ did not lead to signifcant effect. In terms of the average removal efficiency of NO_x, mix No. 1 using a TiO₂ mixing ratio of 0% had a removal efficiency of 0.57% on average; thus, the removal effect w as not significant. For the other samples prepared by mixing, the average removal efficiencies for mix No. 2 (5% TiO₂) were 58.86% and 62.05% for normal and washing surface treatments, respectively, and those of sample No. 3 (10% TiO₂) were 59.94% and 67.61%. mixs No. 4 (5%) and No. 5 (10%), in which TiO₂ diluted with distilled water was sprayed onto the block surface, had an average NO_x removal efficiency of 61.72% and 68.48%, respectively. In terms of NOx removal efficiency, Mixs No. 3 and No. 5 with 10% TiO₂ were better than Mixs No. 2 and No. 4 with 5% TiO₂. In addition, analyzing the NO_x removal efficiency results from the fixing method, it was capable to apply mixing (washing) and the diluted spray methods. Therefore, it was found that the diluted spray method applied in this study can be employed in any manufacture of air purification concrete blocks.

• Journal of Biosystems Engineering
• /
• v.37 no.6
• /
• pp.420-428
• /
• 2012

Purpose: Porcine proliferative enteropathy(PPE), caused by the obligate intracellular bacterium Lawsonia intracellularis, is a widely distributed disease throughout the world causing substantial economic loss. The bacterial pathogen invades the intestinal epithelial cells which causes hyperplasia of the infected cells and leads to the process of disease pathogenesis. For diagnosing PPE in a pig farm in earlier stage, a rapid diagnosing test equipment is needed for farmers. To test the equipment appropriately, we prepare the samples and antibodies for rapid detecting the Lawsonia intracellularis in pig feces. Methods : To prepare the PPE infected samples, we sampled PPE suspected pig feces in a pig farm. To manufacture a anti-Lawsonia intracellularis antibody for capturing the Lawsonia intracellularis, the rabbit-anti LsaA synthetic peptide polyclonal antibody was inoculated to rabbits. To select the couple of antibodies which is most well sandwiched with the bacteria, ELISA test was done with PPE infected ileum samples. Finally, to verify the PPE infected feces which would be used to test the rapid kit, PCR test was done on the sampled PPE suspected feces Results : The rabbit-anti LsaA synthetic peptide polyclonal antibody is developed, and is verified to capture the bacterial well through the fluorescence antibody test. Also, we found that the monoclonal antibody and the polyclonal antibody could be used as couples for sandwiching the bacteria. Finally, through the PCR test for samples of pig feces, we could prepare the 150 PPE positive samples and 50 PPE negative samples. Conclusions : The manufactured polyclonal antibody and the imported monoclonal antibody could be used to capture the bacteria using the sandwich techniques. Also, the prepared PPE infected negative and positive samples could be used to test the performance of the rapid kit to capture the bacterium Lawsonia intracellularis.

• Korean journal of food and cookery science
• /
• v.15 no.2
• /
• pp.158-162
• /
• 1999

A beverage was manufactured with onion extract for which onions were boiled with water and filtered. The concentration of cyclodextrin was studied to improve its quality in manufacturing the onion beverage and its antioxidative and antifatigue effect was investigated in vitro or in vivo. One percent of cyclodextrin was optimum concentration to prevent precipitation and to remove pungent taste and keep mild taste during storage at room temperature and 40$^{\circ}C$. Water extract of onion, used to manufacture onion beverage shown significant difference in antioxidative effect based on peroxide value and thiocyanate method. For the study of antifatigue, swimming performance of mice which fed with onion beverage and water extracts of onion and garlic for 2 weeks was investigated. The mice fed with onion beverage swam longer than those fed with water extract of onion and garlic.

• Clean Technology
• /
• v.23 no.2
• /
• pp.181-187
• /
• 2017

The perfluorocompounds (PFCs) emitted from the semiconductor and display manufacture is treated by abatement systems which use various technologies, such as combustion, thermal, plasma, catalyst. However, it is required that the system should overcome their drawbacks with excess energy consumption and low removal efficiency. The new technology using combination of pressure swing adsorption and excess enthalpy combustion for the reduction of PFCs emissions were developed and analyzed its characteristics. PFCs concentration ratio and PFCs loss factor were calculated from measuring concentration of PFCs at the calculated by comparing concentration of PFCs at the combustor's inlet and outlet. There were performance evaluations with various gas flow for comparing energy consumption and removal efficiency with existing equipments. The concentration ratio and the loss factor of PFCs were 1.65, 8.2%, respectively, when the total gas flow of the pressure swing absorption (PSA) inlet was 204 liter per minute (LPM) and $CF_4$ concentration was 1412 ppm. In comparison with existing system at constant condition, $CF_4$ removal efficiency for a porous media combustion (PMC) showed the improvement more than 16% and the consumed energy was also reduced up to approximately 41%. Then, the total gas flow introduced into PMC and $CF_4$ concentration were 91-LPM and 2335 ppm, respectively, and the destruction and removal efficiency of $CF_4$ was about 96% at 19-LPM $CH_4$, and 40-LPM $O_2$.

• Membrane Journal
• /
• v.30 no.4
• /
• pp.269-275
• /
• 2020

In this study, CO₂ separation experiment was performed on a CH₄/CO₂ mixed gas using a ceramic hollow fiber membrane contactor (HFMC). In order to fabricate high-performance HFMC, experiments were conducted to manufacture high-permeability hollow fiber membranes, and the prepared hollow fiber membranes were evaluated through N₂ gas permeation experiments. HFMC for CH₄/CO₂ mixed gas separation was manufactured using the manufactured high-permeability hollow fiber membrane. In the experiment, mixed gas of CH₄/CO₂ (34.5% CO₂, CH₄ balance) and monoetanolamine (MEA) was used, and the effect of CO₂ removal efficiency on the flow rate of the absorbent was evaluated. The CO₂ removal efficiency increased as the liquid flow rate increased, and the CO₂ absorption flux also increased with the liquid flow rate.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.1
• /
• pp.1-11
• /
• 2005

Several Solid Freeform Fabrication Systems(SFFS) are commercialized in a few companies for rapid prototyping. However, they have many technical problems including the limitation of applicable materials. A new method of agile prototyping is required for the recent manufacturing environments of multi-item and small quantity production. The objectives of this paper include the development of a novel method of SFFS, the CAFL/sup VM/(Computer Aided Fabrication of Lamination for Various Material), and the manufacture of the various material samples for the certification of the proposed system and the creation of new application areas. For these objectives, the technologies for a highly accurate robot path control, the optimization of support structure, CAD modeling, adaptive slicing was implemented. However, there is an important problem with the conventional 2D lamination method. That is the inaccuracy of 3D model surface, which is caused by the stair-type surface generated in virtue of vertical 2D cutting. In this paper, We design the new control algorithm that guarantees the constant speed, precise positioning and tangential cutting on the 5DOF SFFS. We develop the tangential cutting algorithm to be controlled with constant speed and successfully implemented in the 5DOF CAFL/sup VM/ system developed in this paper. Finally, this paper confirms its high-performance through the experimental results from the application into CAFL/sup VM/ system.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.190-193
• /
• 2015

The current sea route sign system based on an electronic marine chart only has a data manufacture specification for uses at ECDIS. Therefore, it has a limitation in expressing various sea route data and falls short of productivity as it is frozen to prevent being changed for a long time. Also, it cannot satisfy requirements from high tech such as lattice structure data and time series information. Currently, although it builds each independent operation system based S-57, it has been found that it is the most important requirement from consumers that the entire monitoring system can mutually interwork by standardizing and uniting formats of all protocols. In addition, current status information and alarm system is using AIS, TRS, WCDMA telecommunication and processing all the data after saving it into each different server. Lighthouse lantern which currently has used was utilized to do a performance test of a developed system. All of created data was trasmitted through the RS-232, It is clear that the data was received by a situation monitoring system. In addition, when the data was transmitted after saving in a database, same data was ordinarily received. In this thesis, we will implemented the status information and alarm system of Marine transportation facilities which is a sea route sign system based on S-63 electronic marine chart, S/W, after uniting each different protocol and making combined system.

• Journal of the Korean Institute of Gas
• /
• v.24 no.2
• /
• pp.44-49
• /
• 2020

In this paper, a measuring circuit is designed through analyzing manufacture specification of the sensor based on MOS. And the best input-output polynomial are induced that really gas sensors are used in gas safety management industrial fields. Response characteristics of a MOS gas sensor is analysed by through sensor's output voltages are measured after standard gases with six kinds of concentrations are manufactured and are injected to the sensor. A lookup table is created by relations of sensor's output voltages by injecting gases with other concentrations. Because data of the formed lookup table are equal interval, a polynomial can be induced of method of approximation function. So the 5th polynomial of input-output for a sensor is defined, coefficients are calculated by using least squares method, and the 5th polynomial is completed for representing characteristics of the sensor. If the proposed polynomial is applied to gas leak detectors, an inverse transformation of polynomial and programing of array codes are recreated. In this research, polynomial is implemented with array types that intervals of values of a lookup table are one-fifth sampled and interpolated. The performance of proposed 5th calibration equation is verified that errors are reduced than a linear expression when tests are performed by measurement of concentrations against injection of standard gases.

• Korean Journal of Optics and Photonics
• /
• v.24 no.5
• /
• pp.224-230
• /
• 2013

Laser Lift-Off (LLO) is a process that removes a GaN or AIN thin layer from a sapphire wafer to manufacture vertical-type LEDs. It consists of a light source, an attenuator, a mask, a projection lens and a beam homogenizer. In this paper, we design an attenuator and a projection lens. We use the 'ZEMAX' optical design software for analysis of depth of focus and for a projection lens design which makes $7{\times}7mm^2$ beam size by projecting a beam on a wafer. Using the 'LightTools' lighting design software, we analyze the size and uniformity of the beam projected by the projection lens on the wafer. The performance analysis found that the size of the square-shaped beam is $6.97{\times}6.96mm^2$, with 91.8 % uniformity and ${\pm}30{\mu}m$ focus depth. In addition, this study performs dielectric coating using the 'Essential Macleod' to increase the transmittance of an attenuator. As a result, for 23 layers of thin films, the transmittance total has 10-96% at angle of incidence $45-60^{\circ}$ in S-polarization.