• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.7 no.4
• /
• pp.51-56
• /
• 2011

Steam generator is one of the main equipments that affect safety and long term operation in nuclear power plants. Fluid flows inside and outside of the steam generator tubes and induces vibration. To prevent the vibration the tubes are supported by AVB (anti vibration bar). When the steam generator tube contact to AVB, it is damaged by the accumulation of wear and corrosion. Therefore studies are required to determine the effects of the gap between the steam generator tube and AVB. In order to obtain the stress and the displacement distributions of the steam generator tube, three dimensional finite element analyses were performed by using the commercial program ANSYS. Using the calculated the stress and the displacement distributions, the static residual strength of the steam generator tube can be evaluated. The results show that the stress and displacement of the steam generator tube increase significantly compared with the results from a zero-gap model.

• Structural Engineering and Mechanics
• /
• v.60 no.2
• /
• pp.337-350
• /
• 2016

Even though extensive researches have been performed for steam explosion due to their complex mechanisms and inherent uncertainties, establishment of severe accident management guidelines and strategies is one of state-of-the arts in nuclear industry. The goal of this research is primarily to examine effects of vessel failure modes and locations on nuclear facilities under typical steam explosion conditions. Both discrete and integrated models were employed from the viewpoint of structural integrity assessment of steel components and evaluation of the cracking and crushing in reinforced concrete structures. Thereafter, comparison of systematic analysis results was performed; despite the vessel failure modes were dominant, resulting maximum stresses at the all steel components were sufficiently lower than the corresponding yield strengths. Two failure criteria for the reinforced concrete structures such as the limiting failure ratio of concrete and the limiting strains for rebar and liner plate were satisfied under steam explosion conditions. Moreover, stresses of steel components and reinforced concrete structures were reduced with maximum difference of 12% when the integrated model was adopted comparing to those of discrete models.

• Korean Journal of Cleft Lip And Palate
• /
• v.15 no.2
• /
• pp.89-96
• /
• 2012

Le Fort 1 osteotomy or maxillary advancement with distraction osteogenesis (DO) is main treatment strategy for cleft palate patients with maxillary hypoplasia. Maxillary DO allows greater maxillary advancement within physiological limit than Le Fort 1 osteotomy. Moreover, it is better for velopharyngeal function. However, there is a greater tendency for an increase in nasal sound when maxilla is advanced excessively. Therefore, the advancement of anterior maxillary segment using DO has been utilized. It offers advantages such as an increase in the length of the palate, a prevention of the change in palatopharyngeal depth, and a preservation of the velopharyngeal function. Moreover, it will obliterate the necessity of bone graft, and it prevents the occurrence of oronasal or oroantral fistula. Finally, it stimulates the regeneration of the soft and hard tissue of alveolus, and subsequently makes possible to place implant.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.2
• /
• pp.209-220
• /
• 2000

For non-linear analysis of stiffened shell structures, the total Lagrangian formulation is presented based upon the degenerated shell element. Geometrically correct formulation is developed by updating the direction of normal vectors and taking into account second order rotational terms in the incremental displacement field. Assumed strain concept is adopted in order to overcome shear locking phenomena and to eliminate spurious zero energy mode. The post-buckling behaviors of stiffened shell structures are traced by modeling the stiffener as a shell element and considering general transformation between the main structure and the stiffener at the connection node. Numerical examples to demonstrate the accuracy and the effectiveness of the proposed shell element are presented and compared with references' results.

• 연구논문집
• /
• s.33
• /
• pp.39-51
• /
• 2003

This paper deals with the noise measurement and evaluation method of a reciprocating air-compressor and its noise reduction. Lead-wrapping techniques are employed to identify the contribution of principal noise sources which are generally known as motor, belts, suction/discharge valves, moving piston, and flow-induced noise which are caused by edges or discontinuities along the flow path e.g. expansions, contractions, junctions and bends. As a result, it can be found that main noise sources of the air-compressor can be categorized by the suction/discharge noise, valve noise, and compressed-air tank noise. Based on the investigations, mufflers are designed to reduce both the suction/discharge noise and the compressed-air tank noise. Instead of the conventional valve plate, engineering plastics are used as a new one for the reduction of valve impact noise. In addition, attempts are made to reduce the valve noise propagation to the cylinder head and the compressor tank by using the insulation casings in the cylinder head. As a result of the countermeasure plans, it can be achieved that the noise reduction of the air-compress is up to 10 dB.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.2
• /
• pp.178-186
• /
• 2018

The scale effects on the permanent deformations and fractures of structures subjected to impact loadings have been aware by structural engineers for a long time. Experimental investigations have been performed with various structures to demonstrate the effects, but very few are directly related with marine structural elements. Furthermore, the causes of the scale effects have not clearly been answered yet. In this study, to quantify the scale effects on the permanent deflections, lateral collision tests were performed on steel unstiffened plates and the numerical analyses of the tested models were also conducted using a commercial package, Abaqus. After the substantiation of the numerical tool using the test results, a parametric study was carried out considering and neglecting the strain-rate hardening. Based upon the parametric study results, it may be concluded that the main cause of the scale effects on the permanent deflections of steel unstiffened plates subjected to lateral collision loads is the strain-rate effects.

• Solar Energy
• /
• v.7 no.2
• /
• pp.37-53
• /
• 1987

This study has been prepared for the purpose of developing the system performance prediction method of natural circulation solar hot water system. The storage tank of the natural circulation solar hot water system equipped with flat-plate solar collector is located at higher elevation than the solar collectors. Therefor, the storage tank temperature distribution formed accordance with configuration of storage tank by flow rate of circulating fluid affect system collection efficiency. In this study measure the storage tank temperature distribution with various experimental system under real sun condition and present the theoretical prediction method of the storage tank temperature. Moreover measure the flow rate not only day-time but also night-time reverse flow rate with die injection visual flow meter. Main conclusion obtain from the present study is as follows; 1) The storage tank temperature distribution above the connecting pipe connection position is the same as that of the fully mixed tank and below the connection position is the same as that of stratified tank. 2) The system performance sensitive to the storage tank temperature distribution. Therefore detailed tank model is necessary. Average storage tank temperature can be calculate 3% and storage tank temperature profile can get less than 10% difference with this model system.

• Ocean and Polar Research
• /
• v.23 no.1
• /
• pp.23-34
• /
• 2001

Geochemical and Sr-Nd isotopic compositions and K-Ar ages are analyzed in volcanic rocks from Weno Island, Caroline Islands. Seven Weno lava samples of alkali basalt and basaltic trachyandesite are aphyric or sparsely phyric comprising olivine, plagioclase, and clinopyroxene phenocrysts. Whole-rock geochemical variation of Weno lavas reflects main fractional crystallization of olivine and Cr-spinel phenocrysts. Newly determined K-Ar ages of Weno lavas range from 6.7 to 11.3 Ma (late Miocene), indicating their formation during primary volcanic stage of Chuuk Islands. Trace element compositions of Weno lavas are very similar to those of typical ocean island basalts (OIBs), suggesting their formation during intra-plate mantle plume activity. The plume composition is isotopically very similar to that of Hawaiian hot spot. However, the age span of Chuuk volcanism is longer than that of the other individual volcanoes in the Pacific.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.3
• /
• pp.127-133
• /
• 2017

Performance analysis has been carried out on a high side scroll compressor that had a fixed scroll equipped with a circular oil groove on its thrust surface. Oil was supplied to the oil groove through an intermittent opening from a high pressure oil reservoir formed inside the orbiting scroll hub. Oil in the groove was then delivered to both suction and back pressure chambers by pressure differentials and viscous pumping action of the orbiting scroll base plate. Mathematical modeling of this oil groove system was incorporated into a main compressor performance simulation program for an optimum oil groove design. The study findings were as follows. Pressure in the oil groove can be controlled by changing its configuration and the oil passage area. With an enlarged oil passage, the pressure in the oil groove heightens due to an increased flow rate, but the pressure elevation in the back pressure chamber is small, resulting in reduced friction loss at the thrust surface between the two scrolls. On the other hand, by increasing the oil passage area, the oil content in the refrigerant flow increases. Considering all these factors, the energy efficiency ratio could be improved by about 3.6% under the ARI condition by an optimal oil groove design.

• Journal of the Korea Safety Management & Science
• /
• v.11 no.1
• /
• pp.27-33
• /
• 2009

A study of fracture to material is getting interest in nuclear and aerospace industry as a viewpoint of safety. Acoustic emission (AE) is a non-destructive testing and new technology to evaluate safety on structures. In previous research continuously, all tensile tests on the pre-defected coupons were performed using the universal testing machine, which machine crosshead was move at a constant speed of 5mm/min. This study is to evaluate an AE source characterization of SM45C steel by using k-nearest neighbor classifier, k-NNC. For this, we used K-means clustering as an unsupervised learning method for obtained multi -variate AE main data sets, and we applied k-NNC as a supervised learning pattern recognition algorithm for obtained multi-variate AE working data sets. As a result, the criteria of Wilk's $\lambda$, D&B(Rij) & Tou are discussed.