• Journal of Environmental Health Sciences
• /
• v.13 no.2
• /
• pp.51-63
• /
• 1987

We identified pyrolysis condition, effect of catalyzer and pyrolysis mechanism through contact decomposed method by adding Bentonite in waste plastic of hospital solid waste. The result from this study were summarized as the followings: 1. The optimum fuel oil were obtained when hospital wasted plastic (P.P) and Bentonite were mixed in the ratio of 30:1. 2. Maximum absorption wave of hospital wasted plastic (P.P) appeared at 2900cm$^{-1}$, 1480cm$^{-1}$, 1360cm$^{-1}$ and 1180 cm$^{-1}$ by FT-IR and the plastics were identified and confirmed. 3. Reaction temperature of hospital wasted plastic started at 360$\circ$C, proceed rapidly at 437.5$\circ$C and finished at 481$\circ$C. The residue was 0.729%. When bentonire was added started at 318$\circ$C, proceed rapidly at 399.5$\circ$C and finished at 449.3$\circ$C, the residue being 4.23%. 4. Pyrolysis products of hospital wasted plastic were about 90 kinds. The Main components were 2-Heptene-3-ethyl-4-trimethyl (27.4%), 1-Heptene-2-isobutyl-6-methyl (8.6%) and 1-Heptene decene (7.7%). There was little component difference at different temperature. This is the result from stability of decomposition product. 5. Pyrolysis efficiency increased by the addition Bentonire. 6. Some of the Environmental and Sanitary problems could be solved by the pyrolysis of hospital wasted plastic and the decomposed products were to be used as fuel oil.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.2
• /
• pp.81.3-81.3
• /
• 2017

In this paper, we report a small-scale emerging island and double arc loops, which are associated with a M6.5 flare, in Active Region 12371. We investigate the spatial and temporal changes of both photospheric magnetic fields using SDO/HMI data and coronal magnetic structures obtained from nonliner force-free field (NLFFF) extrapolation. From the vector magnetograms, we find a small-scale emerging island near the main polarityy inversion line about three hours before the flare. The island has a strong shear angle, which is determined by difference between transverse component of observed field and potential field, of around 90 degrees. Furthermore, the NLFFF well reproduces a sigmoidal structure seen in SDO/AIA 94, which is consistent with the double arc loops configuration suggested by Ishiguro and Kusano (2017) who introduced a magnetic configuration showing the double arc instability. The observed emerging island is located among the double arc loops, which is also supproted by their model. Finally, there was an eruption (M6.5 flare) associated with the loops. We discuss a possible role of the double arc instability for the eruption.

• The Korean Journal of Community Living Science
• /
• v.27 no.3
• /
• pp.387-403
• /
• 2016

This study explored the relationships between unmarried adult children and their coresident parents with a focus on the role of intergenerational exchanges and family values affecting parent-child relations. A total of 767 unmarried adult children who lived with their parents were selected from the data of the third National Korean Family Survey in 2015. The main findings were that coresident adult children exchange diverse resources with their parents and that exchange patterns whether receiving more or giving more differed depending on the helping dimensions. 'Receiving' type was more prominent in the dimension of practical help, while, 'receiving and giving' type was more noticeable in the dimension of emotional help. Findings also suggest that intergenerational exchange and family values contribute to parent-child relationship quality. While being an active provider of practical help is positively associated with relationship quality, being a recipient of emotional help is related to a higher level of relationship quality compared to being indifferent. In addition, a stronger value of family responsibility was associated with a higher level of relationship quality. These findings indicate that the importance of the practical and emotional component in the relationships between unmarried adult children and their co-resident parents and reciprocal intergenerational exchange and strong family values may be contributory factors to better parent-child relationships.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.3
• /
• pp.9-15
• /
• 2017

This study represents basic research for the development of submerged pump technology applicable to transfer and storage of a cryogenic liquids. Its purpose is to secure baseline design data by applying reverse engineering to the process of developing a submerged cryogenic pump. The two-stage model included in the ARTICK Series LNG Submerged Pump produced by Vanzetti of Italy was selected for analysis for development of a localized product, and was disassembled for reverse engineering. The pump was disassembled after analyzing its processing/assembly characteristics such as shrinkage of fittings. In addition, the materials used in manufacturing of the main components were analyzed, and the ingredients were confirmed. As a result, a design drawing for each component required for product development was secured via foundational design, and a test product was manufactured by maximizing the application of appropriate domestic technologies.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.2
• /
• pp.170-177
• /
• 1998

The purpose of superconducting magnetic bearing flywheel energy storage system(SMB-FESS) is to store unused nighttime electricity as kinetic energy and convert it to electricity during daytime. The SMB-FESS is proposed as an efficient energy storage system because there is no mechanical problems, such as friction and wear The flywheel over SMB is rotated at a high speed, 50,000rpm. The major source of energy loss in the SMB-FESS is vibration of flywheel. Therefore, the vibration characteristics of SMB-FESS should be identified. In this study, the axial/radial stiffness and damping coefficient of SMB are measured by a vibration test. Natural frequencies and natural modes of flywheel and magnet are analyzed by a finite element method. The modal analysis of system is performed using the modal parameters of each component and the measured stiffness/damping coefficient. So, natural at frequencies and mode shapes of the joined system can be obtained. According to critical speed analysis, the system has two rigid conical modes in the low speed range. Nevertheless, the system has not been affected by the critical speed in the main operating range.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.265-266
• /
• 2006

The chemical conversion coating formed on magnesium alloy investigated for low cost and harmless in environment by using the colloidal silica as the main component. The film formed in 298 K is thick, the film, which was thought combination of Si-O, was formed. The film formed in 313 K is thinner than that in 298 K. The quantity of film formed at high temperature such as 333 K and 353 K is smaller than dissolved quantity. At the anodic polarization experiment, corrosion resistance in sealing by hot water after chemical conversion treatment in basic solution condition get worse than that in comparison with basic solution condition. In salt spray test, the ratio of black rust on specimen that did not conducted chemical conversion treatment was five times or more compared with those of chemical conversion treated specimen. The film thickness of chemical conversion coating produced by alkali treatment process is thinner than in comparison with that of specimen produced in basic chemical conversion treatment solution condition. It is thought, however, that it showed good corrosion resistance during salt spray test because the area of microcracks is small.

• Proceedings of the KSPS conference
• /
• 2007.05a
• /
• pp.207-210
• /
• 2007

As the Internet is prevalent in our life, harmful contents have been increasing on the Internet, which has become a very serious problem. Among them, pornographic video is harmful as poison to our children. To prevent such an event, there are many filtering systems which are based on the keyword based methods or image based methods. The main purpose of this paper is to devise a system that classifies the pornographic videos based on the audio information. We use Mel-Cepstrum Modulation Energy (MCME) which is modulation energy calculated on the time trajectory of the Mel-Frequency cepstral coefficients (MFCC) and MFCC as the feature vector and Gaussian Mixture Model (GMM) as the classifier. With the experiments, the proposed system classified the 97.5% of pornographic data and 99.5% of non-pornographic data. We expect the proposed method can be used as a component of the more accurate classification system which uses video information and audio information simultaneously.

• International Journal of Quality Innovation
• /
• v.6 no.3
• /
• pp.204-215
• /
• 2005

This paper explores innovative manufacturing processes, which can be used to manufacture the national musical instrument of Trinidad and Tobago, the Musical Steel Drum or Steel Pan. The main manufacturing process used today is the manual hand-forming technique. In order to achieve more consistent and deeper formed components while maintaining the high quality of the instrument, it is proposed that the Marforming process and the Flow-forming process, an adaptation of the Spinforming process, be used more frequently in the future to replace the traditional Hand-forming method. In the traditional Spinforming technique material is pushed from the outer circumference of the metal disc to the center in progressive passes of the former. This results in a thinning of the outer region of the formed component with thickening of the center, however the opposite is required for the musical steel drum and by adapting the process the required strain distributions were achieved. Evaluation took the form of strain analyses of pre-formed steel drums and visual inspection of the quality of the surface finish. It was found that the Marformed components had the smallest range of strain values while the Spinformed components had the largest range.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.4
• /
• pp.403-407
• /
• 2014

To use vibration energy to generate electricity, a resonance vertical linear electric generator was applied to the suspension of a vehicle in a previous paper. However, the working conditions, including mass change in the vehicle body related to the cargo on board, number of passengers and the temperature difference caused by the operating environment, can influence the permanent magnet, which is the main component of the electric generator. Therefore, a robust optimum design is required to minimize the influences from the diverse operation conditions and maximize the electromotive force of the electric generator. In this paper, a resonance linear electric generator is introduced. Vibration response analysis to find the input velocity of the electric generator and an electromagnetic transient analysis to apply changes in the performance of the permanent magnet are performed. Finally, the optimum value of each design variable is derived using a Taguchi method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.35-44
• /
• 2011

Mathematical modelling for liquid rocket engine(LRE) main components were conducted to predict the dynamic characteristics when the LRE operates at the transient condition, which include engine start up, shut down, or thrust control. Propellant feeding system is composed of fuel and oxidizer feeding components except for regenerative cooling channel for the fuel circuit. Components modeling of pump, pipe, orifice, control valve, regenerative cooling channel and injector was serially made. Hydraulic tests of scale down component were made in order to validate modelling components. The mathematical models of engine components were integrated into LRE transient simulation program in concomitant with experimental validation.