• Nuclear Engineering and Technology
• /
• v.52 no.9
• /
• pp.2078-2084
• /
• 2020

Magnesium oxide (MgO) and Zinc oxide (ZnO) nanoparticles (NPs) have been successfully synthesized by solid-solid reaction method. The structural properties of ZnO and MgO NPs were studied using X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD results indicated a formation of pure MgO and ZnO NPs. The mean diameter values of the agglomerated particles were around to be 70 and 50 nm for MgO and ZnO NPs, respectively using SEM analysis. Further, a wide-range of nuclear radiation shielding investigation for gamma-ray and fast neutrons have been studied for Magnesium oxide (MgO) and Zinc oxide (ZnO) samples. FLUKA and Microshield codes have been employed for the determination of mass attenuation coefficients (μ_m) and transmission factors (TF) of Magnesium oxide (MgO) and Zinc oxide (ZnO) samples. The calculated values for mass attenuation coefficients (μ_m) were utilized to determine other vital shielding properties against gamma-ray radiation. Moreover, the results showed that Zinc oxide (ZnO) nanoparticles with the lowest diameter value as 50 nm had a satisfactory capacity in nuclear radiation shielding.

• Korean Journal of Community Nutrition
• /
• v.7 no.1
• /
• pp.111-120
• /
• 2002

Postmenopausal women lose more bone mass than men as a result of estrogen deprivation. The resultant low bone mineral density (BMD) is a major risk factor in the development of osteoporosis. Calcium, phosphorus and magnesium are main components of bone. The purpose of this study is to investigate nutrient intake and serum osteocalcin, Ca, P and Mg and their correlation to bone mineral density in Korean postmenopausal women residing in rural areas. We conducted 24 hour dietary recalls, anthropometric measurements and blood analysis on 60 postmenopausal women. The BMD of the lumbar spine (L2$\rightarrow$L4) and the femoral neck were measured by dual energy X-ray absorptiometry (DEXA). Subjects were assigned to one of three groups:normal (T-score> -1, n=20), osteopenia (-2.5> T-score $\leq$ -1, n=23), and osteoporosis ( T-score $\leq$ -2.5, n=17). The mean age, height, weight and BMI were 62.37 yr, 154.36 cm, 55.28 kg and 23.18 $kg/m^2$ respectively. The mean daily energy and protein intakes were 76.35% and 87.41% of RDA for Koreans. The mean intakes of calcium, phosphorus, and magnesium were 463.62 mg (66.23% of RDA), 955.32 mg (136.47% of RDA), 345.87 mg respectively. The mean serum levels of calcium, phosphorus and magnesium were 8.76 mg/dl, 3.80 mg/dl, and 2.10 mg/dl, respectively, and there were no significant differences among the three groups. However, the BMD of the femoral neck showed a significantly negative correlation with serum magnesium (p<0.05). To summarize the results, most nutrient intakes (especially calcium) in postmenopausal women did not reach the RDA values for Koreans. Also, increase of serum magnesium levels may be related to bone loss.

• Journal of Powder Materials
• /
• v.18 no.3
• /
• pp.283-289
• /
• 2011

Magnesium hydroxide sulfate hydrate whiskers ($5Mg(OH)_2{\cdot}MgSO_4{\cdot}3H_2O$, abbreviated 513 MHSH) were prepared using hydrothermal reaction with magnesium oxide (MgO) and magnesium sulfate ($MgSO_4{\cdot}7H_2O$) as the starting materials. The effects of the molar ratio of $MgSO_4$/MgO and amount of $NH_4OH$ were studied. As a result, 513 MHSH whiskers co-existed with hexagonal plate $Mg(OH)_2$ at low concentration of $SO_4^{2-}$. The molar ratio of $MgSO_4{\cdot}7H_2O$/MgO was 7:1, uniform 513 MHSH whiskers were formed without impurity such as $Mg(OH)_2$. Appropriate amount of $NH_4OH$ has affected to formation of high quality MHSH. Their morphologies and structures were determined by powder X-ray diffraction (XRD) scanning electron microscopy (SEM) and thermo-gravimetric analyzer (TGA).

• Journal of the Korean institute of surface engineering
• /
• v.46 no.3
• /
• pp.116-119
• /
• 2013

To improve the corrosion resistance of an electrogalvanized steel sheet, we deposited magnesium film on it using a vacuum evaporation method and annealed the films at $250-330^{\circ}C$. The zinc-magnesium alloy is consequently formed by diffusion of magnesium into the zinc coating. From the anodic polarization test in 3% NaCl solution, the films annealed at $270-310^{\circ}C$ showed better corrosion resistance than others. In X-ray diffraction analysis, $ZnMg_2$ was detected through out the temperature range, whereas $Mg_2Zn_{11}$ and $FeZn_{13}$ were detected only in the film annealed at $310^{\circ}C$. The depth composition profile showed that the compositions of Mg at $270-290^{\circ}C$ are evenly and deeply distributed in the film surface layer. These results demonstrate that $270-290^{\circ}C$ is a proper temperature range to produce a layer of $MgZn_2$ intermetallic compound to act as a homogeneous passive layer.

• Journal of Korea Foundry Society
• /
• v.13 no.5
• /
• pp.441-449
• /
• 1993

SiC particulate reinforced magnesium matrix composites were fabricated by melt stirring method. The effet of several factors on mechanical properties and the efficiency of melt stirring method from the viewpoint of these properties were investigated. The tensile strength increased and the elongation decreased with decrease of the particle size or the increase of the paticulate volume fraction for pure magnesium matrix and Mg-5%Zn alloy matrix composites. A longer stirring time improved the tensile strength of these composites. The tensile strength of Mg-5%Ca alloy matrix composites which shows no uniform paticulate distribution was a little lower than that of matrix alloy. Rapid solidification rate is preferred for the improved tensile strength of these composites. The pure magnesium matrix and Mg-5%Zn alloy matrix composites have tensile strength of about 400MPa. This value agrees with the tensile strength of some magnesium matrix composites fabricated by liquid infiltration method or powder metallurgy method at the same volume fraction of reinforcements of whisker or particle. Therefore, the melt stirring method which has the advantages of simple process is considered to be efficient in fabricating magnesium matrix composites.

• Korean Journal of Metals and Materials
• /
• v.50 no.10
• /
• pp.745-751
• /
• 2012

The Kroll process for magnesium reduction of titanium tetrachloride is used for mass production of titanium sponge. The present study was conducted in a lab scale reactor to develop a better understanding of the mechanism of titanium sponge formation in the Kroll reactor with respect to reaction degrees and the feeding rate of $TiCl_4$. The $MgCl_2$ produced during the initial stage of the reaction was not sunk into the molten magnesium, but covered the surface of the molten magnesium. As a result, subsequently fed $TiCl_4$ reacted with Mg exposed on the edge of molten $MgCl_2$ in the crucible. Therefore, titanium sponge grew toward the center of the crucible from the edge. The temperature of the molten magnesium increased remarkably with the increasing feeding rate of $TiCl_4$. Consequently, fed $TiCl_4$ reacted at the upper side of the crucible with evaporated Mg, and produced titanium on the upper surface of the crucible wall, which increased considerably with the feeding rate of $TiCl_4$.

• Journal of Electrochemical Science and Technology
• /
• v.3 no.4
• /
• pp.159-164
• /
• 2012

Magnesium (Mg) deposition and dissolution behaviors of 0.2 M $MgBu_2-(AlCl_2Et)_2$, 0.5 M $Mg(ClO_4)_2$, and 0.4M $(PhMgCl)_2-AlCl_3$-based electrolytes with and without tris(pentafluorophenyl) borane (TPFPB) are investigated by ex situ scanning electron microscopy (SEM) and galvanostatic cycling of Mg/copper (Cu) cells. To ascertain the factors responsible for the anodic stability of the electrolytes, linear sweep voltammogrametry (LSV) experiments for various electrolytes and solvents are conducted. The effects of TPFPB as an additive on the anodic stability of 0.4M ($(PhMgCl)_2-AlCl_3$/THF electrolyte are also discussed.

• Corrosion Science and Technology
• /
• v.7 no.3
• /
• pp.152-157
• /
• 2008

New wrought magnesium alloys have increasingly been developed in recent years for the automotive industry due to their high potential as structural materials for low density and high strength/weight ratio demands. However, their poor mechanical properties and low corrosion resistance have led to a search for new kinds of magnesium alloys with better strength, ductility, and high corrosion resistance. The main objective of this research is to investigate the corrosion behaviour of new magnesium alloys: Mg-Zn-Ag (ZQ), Mg-Zn-Mn-Si (ZSM) and Mg-Zn-Mn-Si-Ca (ZSMX). These ZQ6X, ZSM6X1, and ZSM651+YCa alloys were prepared using hot extrusion. AC, DC polarization and immersion tests were carried out on the extruded rods. Microstructure was examined using optical and electron microscopy (SEM) and EDS. The addition of silver decreased the corrosion resistance. The additions of silicon and calcium also affected the corrosion behaviour. These results can be explained by the effects of alloying elements on the microstructure of Mg-Zn alloys such as grain size and precipitates caused by the change in precipitation and recrystallisation behaviour.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.4
• /
• pp.385-393
• /
• 2009

Different types magnesium hydroxide groups have been obtained using the hydrothermal precipitation technique from magnesium sulfate and calcium carbonate solution. The Mg atom coordinated around O atom of ${SO_4}^{2-}$ in another layer to form a multi-layer structure crystal. The influence of synthesis parameters on the morphological characteristics and size of magnesium hydroxide groups precipitated in aqueous were investigated such as different of additive and pH. Magnesium hydroxide groups were decomposed gradually and converted finally to MgO particles after heated in air temperature up to $1050^{\circ}C$. The particle size and it's distribution morphology, crystal phase and thermal behavior of the samples were characterized through XRD, SEM, EDS, and TG/DTA.

• Corrosion Science and Technology
• /
• v.16 no.3
• /
• pp.151-159
• /
• 2017

The MA8 alloy (formula Mg-Mn-Се) has been shown to have greater corrosion stability than the VMD10 magnesium alloy (formula Mg-Zn-Zr-Y) in chloride-containing solutions by Scanning Vibrating Electrode Technique (SVET) and by optical microscopy, gravimetry, and volumetry. It has been established that the crucial factor for the corrosion activity of these samples is the occurrence of microgalvanic coupling at the sample surface. The peculiarities of the kinetics and mechanism of the corrosion in the local heterogeneous regions of the magnesium alloy surface were investigated by localized electrochemical techniques. The stages of the corrosion process in artificial defects in the coating obtained by plasma electrolytic oxidation (PEO) at the surface of the MA8 magnesium alloy were also studied. The analysis of the experimental data enabled us to determine that the corrosion process in the defect zone develops predominantly at the magnesium/coating interface. Based on the measurements of the corrosion rate of the samples with PEO and composite polymer-containing coatings, the best anticorrosion properties were displayed by the composite polymer-containing coatings.