• Transactions of Materials Processing
• /
• v.19 no.3
• /
• pp.179-184
• /
• 2010

The present study is focused on the deep drawability and product qualities of ultra thin beryllium copper sheet metal. The goal of this research is to investigate the limit drawing ratio in deep drawing of ultra thin beryllium copper metal. For the experiment, beryllium copper(C1720, $50{\mu}m$ in thickness) is used. Tensile test are also carried out to find out the material properties. Deep drawing experiments are carried out in Universal Testing Machine(UTM) to obtain limit drawing ratio. Deep drawing tests are carried out for various specimen sizes. Teflon film is used as a lubricant and constant blank holding force is imposed. Sheet thickness and surface hardness are measured along radial direction after deep drawing. Thickness is measured using optical microscope. For beryllium copper(C1720), the maximum LDR of 2.4 is obtained when the die shoulder radius is 20 or 30 times of sheet thickness.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.298-306
• /
• 1993

A portable torque and power measurement system for small farm equipment based on instrumented pulley was developed. The prototype pulley was machined from mild steel, with spokes serving as strain beams. Strain gages mounted to the spokes sense the bending strain due to the torque and convert this into millivolt output. Calibration results showed the torque-millivolt relationship was linear, while hysterisis and error were less than 1% fs. For power measurements, an additional tachmeter with dcvoltage output is necessary. With the tachometer , error in power measurement was +-1.03W or 0.2% fs. Field tests showed that for ease of installation, no machine alteration needed and safety, this system had advantage over other methods for small farm equipment.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 1999.02a
• /
• pp.65-68
• /
• 1999

The major deisng parameters that are considered in this paper are: 1) EMF according to width of field coil. 2) EMF according to magnetic shield length. Because of superconducting generator (SG) is actually and air cored machine with its rotor iron and stator iron teeth having been removed. In this case, the desing of the SG must be based on the 3D analysis of the magnetic field. This study presents an effective armature winding type with 3D FEM(Finite Element Method), and compares analyzed and measured results.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.129-133
• /
• 2007

Focused Ion Beam(FIB) systems is a useful tool for the fabrication of micro-nano scale structures. In this study, the effects of FIB etching on the Au microstructure are systematically investigated. As the fabrication parameters, ion dose, dwell time and beam overlap ratio are studied. First, the increases of Ga ion dose makes the milling yield higher and the sidewall of milling profile steeper. Dwell time is found to have little effects on the milling profile due to the relatively large milling area of $1\times1{\mu}m^2$ used in this study. However, beam overlap significantly affects not only milling rate but also milling profile. As the beam overlap ratio changes from positive to negative, the development of regular cross-stripe patterns at the bottom with low milling rate is observed.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.2
• /
• pp.137-143
• /
• 2009

This paper presents the fabrication of inchworm motor for high precision actuator system of large displacement and high force. The inchworm motor consists of a extend actuator that provides displacement of tool guide and two clamping actuators which provide the holding force. In order to avoid the PZT fracture, design of pre-load housing was conducted by flexure hinge structure, because PZT actuator has low tensile and shear. To design the pre-load housing and optimize the clamping mechanism, the static and dynamic analysis were conducted by finite element method. From these results, a prototype of the inchworm motor was fabricated and dynamic characteristic with respect to the various frequency was tested. The maximum velocity of the inchworm motor was $41.1{\mu}m/s$ at 16Hz.

• Journal of Korean Institute of Industrial Engineers
• /
• v.26 no.2
• /
• pp.183-192
• /
• 2000

This paper considers the problem of scheduling a set of n jobs on m parallel machines to minimize total weighted tardiness. For the problem a genetic algorithm is proposed, in which solutions are encoded using the random key method suggested by Bean and new crossover operators are employed to increase performance of the algorithm. The algorithm is compared with the Modified Due-Date (MDD) algorithm after series of tests to find appropriate values for genetic parameters. Results of computational tests on randomly generated test problems show that the suggested algorithm performs better than the MDD algorithm and gives good solutions in a reasonable amount of computation time.

• Journal of the Korean Society of Safety
• /
• v.18 no.2
• /
• pp.46-49
• /
• 2003

The magnetic polishing is the useful method to finish some machinery fabrications by using magnetic power. This method is one of the precision techniques and has m aim for clean technology in the transportation of the pure gas in the clean pipes. The magnetic abrasive polishing method is not so common in the field of machine that it is not known to widely. There are rarely researcher in this field because of non-effectiveness of magnetic abrasive. Therefore, in this paper we deals with the development of the magnetic abrasive with the use of Ba-Ferrite. In this development, abrasive grain WA has been made by using the min bond fabricated at low temperature. And magnetic abrasive powder was fabricated from the Ba-Ferrite which was crushed into 200 mesh. The XRD analysis result shows that only WA abrasive and Ba-Ferrite crystal peaks were detected, explaining that resin bond was not any more to contribute chemical reaction. From SEM analysis, we found that WA abrasive and Ba-Ferrite were strongly bonding with each other.

• Korean Journal of Weed Science
• /
• v.13 no.2
• /
• pp.159-163
• /
• 1993

This research was conducted at the Crop Experiment Station to determine the changes of weed flora under direct seeded rice cultivation in dry paddy field from 1989 to 1992 and to establish an effective weed control strategy in direct seeded rice cultivation. With the continuous rice growing under direct seeded rice cultivation in dry paddy field, there were more occurrence in grasses and annual weeds while broadleaf and perennial weeds were diminished. The predominant weeds were aquatic weeds such as Eleocharis kuroguwai, Echinochloa crusgalli, and Monochoria vaginalis in machine transplanted rice paddy field while there were predominant of semi aquatic weed species such as E. crusgalli, Digitaria sanguinalis, Bidens tripartita, Aeschynomene indica, and Arthraxon hispidus in continuous direct seeded rice cultivation in dry paddy condition. Based on the vegetative analysis of weeds in terms of simpson index and community dominance, there was more distribution of weed species in direct seeded rice cultivation on dry paddy condition while only distributed with 1-2 weed species in machine transplanted rice paddy field. In similarity coefficient, there was a gradual increase up to 67% of weeds with the continuous direct seeded rice cultivation in dry paddy condition for 4 years starting from 41% of similarity coefficient.

• Geophysics and Geophysical Exploration
• /
• v.7 no.1
• /
• pp.62-69
• /
• 2004

The objective of this study is to estimate the distribution of a zone disturbed by excavation (EDZ) around tunnels that have been excavated at about 500 m depth in pre-Tertiary hard sedimentary rock. One of the most important tasks is to evaluate changes in the dynamic stability and permeability of the rock around the tunnels, by investigating the properties of the rock after the excavation. We performed resistivity and acoustic tomography using two boreholes, 5 m in length, drilled horizontally from the wall of a tunnel in pre-Tertiary hard conglomerate. By these methods, we detected a low-resistivity and low-velocity zone 1 m in thickness around the wall of the tunnel. The resulting profiles were verified by permeability and evaporation tests performed at the same boreholes. This anomalous zone matched a high-permeability zone caused by open fractures. Next, we performed resistivity monitoring along annular survey lines in a tunnel excavated in pre-Tertiary hard shale by a tunnel-boring machine (TBM). We detected anomalous zones in 2D resistivity profiles surrounding the tunnel. A low-resistivity zone 1 m in thickness was detected around the tunnel when one year had passed after the excavation. However, two years later, the resistivity around the tunnel had increased in a portion, about 30 cm in thickness, of this zone. To investigate this change, we studied the relationship between groundwater flow from the surroundings and evaporation from the wall around the tunnel. These features were verified by the relationship between the resistivity and porosity of rocks obtained by laboratory tests on core samples. Furthermore, the profiles matched well with highly permeable zones detected by permeability and evaporation tests at a horizontal borehole drilled near the survey line. We conclude that the anomalous zones in these profiles indicate the EDZ around the tunnel.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.13 no.5
• /
• pp.81-89
• /
• 2010

This study was conducted to evaluate the effects of early revegetation by analyzing the characteristics of germination and growth of Chrysanthemum zawadskii using vegetation-plant in rock slopes. After making up a growing basis of approximately 20-cm depth and 10-cm diameter by using a boring machine, the surface of rock slopes was planted with vegetation-plant. The number of germinating populations by soil media was 41 in H.s, 4 in T.s, 3 in M.s, and 0 in M.g.s. The germination rate (%) by soil media was 20.0% in H.s, 3.3% in T.s, 2.5% in M.s and 0% in M.g.s. In monthly changes of growth rate, the aspect was northwest direction, the soil media was H.s, and the treatment was microorganism plot. The main factors affecting survivorship and growth of population were soil media and treatment plot. The interaction between each factor had a good effects in bearing x treatment plot, soil media x treatment plot. but, it is recommended that the mulching of vegetation plant is highly needed to help the germination of seed and growth of vegetation because of loss of seed and soil media occurred due to rainfall. Therefore, The result suggests that the revegetation technique using boring in rock slope was very efficient in respect of the early revegetation and the landscape.