• Proceedings of the KSRS Conference
• /
• 2009.03a
• /
• pp.254-259
• /
• 2009

In this study, Simplified Method for the Atmospheric Correction (SMAC) radiative transfer model (RTM) used to retrieve surface reflectance from MODIS Top Of Atmosphere (TOA) reflectance (MOD02). SMAC code provides coefficients which were previously yielded by Second Simulation of the Satellite Signal in the Solar Spectrum (6S) for each satellite sensor. We conducted error analysis of SMAC RTM using MOD02 over comparison with MODIS surface reflectance (MOD09) which was provided from 6S. It showed that low accuracy values such as, $R^2$ : 0.6196, Root Means Square Error (RMSE) : 0.00031, bias : - 0.0859. Thus sensitivity analysis of input parameters and coefficients was conducted to searching error sources. Coefficients about $\tau_p$ (average AOD) are more influence than any other coefficients of $\tau_{a550}$ (Aerosol Optical Depth at 550nm) from sensitivity test. Calibrated coefficients of $\tau_p$ from regression analysis were used to surface reflectance which showed that improve accuracy of surface reflectance ($R^2$ : 0.827, RMSE : 0.00672, bias : - 0.000762).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.7
• /
• pp.599-603
• /
• 2003

Ferroelectric B $i_4$$_{-x}$N $d_{x}$ $Ti_3$ $O_{12}$ (BNdT) thin films with the composition(x=0.75) were prepared on Pt/Ti/ $SiO_2$(100) substrate by metal-organic deposition. The films were annealed by various temperatures from 550 to $650^{\circ}C$ and then the electrical and structural characteristics of BNdT films were investigated for the application of FRAM. Electrical properties such as dielectric constant, 2Pr and capacitance were quite dependent on the thermal heat treatment. The measured 2Pr value on the BNdT capacitor annealed at $650^{\circ}C$ was 56$\mu$C/$\textrm{cm}^2$ at an applied voltage of 5V. In fatigue characteristics value remained constant up to 8$\times$10$^{10}$ read/write switching cycles at a frequency of 1Mhz regardless of annealing temperatures.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2001-2003
• /
• 2005

Various organic acid were used in order to prepare new metalorganic deposition solution for high quality $REBa_2Cu_3O_{7-{\delta}}$ (RE=Y, Eu, Gd) films. Prepared fluorine free MO precursor solution was coated on single crystal (001) $LaAlO_3$ (LAO) by dip coating method. Processing parameters such as oxygen partial pressure, water vapor, ramping rate and pyrolysis temperature etc havebeen controlled in order to make high $J_c$ films with a good epitaxial relationship with substrate. 0.5 micron-thick film was obtained by single coating and no crack appeared after calcination. Oxygen partial pressure was varied in the range of $100{\sim}1,000 ppm$ and conversion heat treatment was carried out at the temperature of $725{\sim}765^{\circ}C$. A critical transition temperature $(T_{c0})$ of 90K and a critical transport current density $(J_c)$ of $>0.5MA/cm^2$ (77K and self-field) were demonstrated for the YBCO film on (001) oriented LAO substrates with a thickness of 0.5 micron. $I_c$ was determined by utilizing a transport measurement. SEM and XRD investigations confirmed that films were grown epitaxially onto the LAO single crystal substrate. It is thought that fluorine free new MOD solutionis promising for high quality REBCO films.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.1
• /
• pp.1-4
• /
• 2007

The total Fluorine content in the precursor solution for MOD processing of YBCO coated conductors can be significantly reduced by synthesizing precursor solution with F-free Y & Cu precursor and Barium trifluoroacetate(TFA). It was shown that crack-free and uniform precursor films were formed after calcinations in humidified oxygen atmosphere. Less than 2 hours are required to finish the calcinations process and XRD measurement shows that $BaF_2,\;CuO,\;Y_2O_3$ are major constituent of calcined precursor films. Film thickness after calcinations was improved to be 2.8um by applying slot-die coating method. In particular, addition of Samarium shows critical current of $I_c=273A/cm-w(J_c=3.8MA/cm^2)$. It is shown that uniform and fast processing route to YBCO coated conductor with high Ic can be provided by employing F-free Y & Cu precursor solution in MOD process.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.1
• /
• pp.14-17
• /
• 2007

The slot-die coating & calcination process was adopted to fabricate the long YBCO precursor films on the buffered metal tape for the $2^{nd}$ generation coated conductors. To obtain the smooth and crack-free surface of long YBCO precursor films, the parameters of slot-die coating and the process variables of calcination step must be optimized simultaneously in reel-to-reel method. Among the parameter of slot-die coating process, the viscosities of the precursor solution was controlled from 60cP to 200cP to obtain the thicker films from on single coating. The slot-die gap, the injection rate of precursor solution, the moving speed of buffered metal tape etc. are controlled lot the full coverage and smooth surface of YBCO precursor films. The slot-die coated films are moved through the tube furnace with predetermined heating profiles in humid oxygen ambient The YBCO precursor films was identifed with $Y_2O_3,\;BaF_2$, and CuO phase by XRD and consisted of fine grains of about 20nm size observed by FE-SEM. The YBCO films show the critical current density over $MA/cm^2$ using the precursor films formed by the continuous slot-die coating & calcination process.

• Journal of the Korean Institute of Gas
• /
• v.25 no.5
• /
• pp.30-36
• /
• 2021

Residual life assessment of reformer tubes of mod HP steel used in the refinery and petrochemical industry were investigated by quantitative metallographic evaluation method. Area fractions of precipitated carbides were measured by using surface replication and its relationship with the remaining life of the tube was investigated. The microstructures of the virgin and other tubes were examined using optical microscopy (OM) for service periods of 1.8, 6.0, 7.2, 8.5, 9.7, and 16.2 years at 950 ℃ and the area fractions of the precipitates were measured by image analysis using ImageJ software. As the area fraction of the precipitates increased, the residual life was decreased accordingly. The results showed that the LMP was the highest in the virgin and the LMP decreased as the service time increased and the residual life decreased. A regressional equation showing the relation between the area fraction of carbides and LMP was experimentally derived. The obtained relationship can be used with the surface replication method for on-site residual life assessment.

• Journal of information and communication convergence engineering
• /
• v.9 no.4
• /
• pp.435-440
• /
• 2011

This paper propose the method of constructing the highly efficiency adder and multiplier systems over finite fields. The addition arithmetic operation over finite field is simple comparatively because that addition arithmetic operation is analyzed by each digit modP summation independently. But in case of multiplication arithmetic operation, we generate maximum k=2m-2 degree of ${\alpha}^k$ terms, therefore we decrease k into m-1 degree using irreducible primitive polynomial. We propose two method of control signal generation for the purpose of performing above decrease process. One method is the combinational logic expression and the other method is universal signal generation. The proposed method of constructing the highly adder/multiplier systems is as following. First of all, we obtain algorithms for addition and multiplication arithmetic operation based on the mathematical properties over finite fields, next we construct basic cell of A-cell and M-cell using T-gate and modP cyclic gate. Finally we construct adder module and multiplier module over finite fields after synthesizing ${\alpha}^k$ generation module and control signal CSt generation module with A-cell and M-cell. Next, we constructing the arithmetic operation unit over finite fields. Then, we propose the future research and prospects.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.05a
• /
• pp.116-116
• /
• 1999

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.96-101
• /
• 2007

[ $YBa_2Cu_3O_{7-{\delta}}$ ] films have been prepared on $LaAlO_3$ (100) single-crystal substrates by a metalorganic deposition using dichloroacetate precursors (DCA-MOD). Calcination conditions were varied in order to optimize the microstructure and the superconducting properties of YBCO film. Coated films were calcined at various temperatures ranging from $400{\sim}700^{\circ}C$ in flowing humid oxygen atmosphere. Ramping rate to calcination tempertures was $2.22^{\circ}C/min$. Conversion heat treatment was performed at $800^{\circ}C$ for 2 h in flowing Ar gas containing 1000 ppm oxygen with a humidity of 9.45%. Observations of surface and cross sectional SEM microstructure showed that the particle size in the calcined film increased in the range of 100-200 nm with heating rate and the calcination temperature. SEM EDS analysis showed that 13 a/o of chlorine was contained in the calcined film. It was also observed that the porosity increased with the heating rate and temperature. Porous microstructure was developed when YBCO films were prepared using porous calcined film. Dense microstructure and high $J_c$ over $1\;MA/cm^2$ was obtained when calcination was carried out at the temperature of $500^{\circ}C$ with a heating rate of $2.22^{\circ}C/min$.

• Nuclear Engineering and Technology
• /
• v.26 no.3
• /
• pp.355-366
• /
• 1994

The USNRC issued a revised ECCS rule that allows the use of best estimate computer codes for safety analysis. The rule also requires an estimation of uncertainty in calculated system response when applying the best estimate computer codes. A practical realistic evaluation methodology to evaluate the ECCS performance that satisfies the requirements of the ECCS rule has been developed and this paper describes the application of new realistic evaluation methodology to large break LOCA for, the demonstration of the new methodology. The computer code RELAP5/MOD3/KAERI, which was improved from RELAP5/MOD3.1, was used as the best estimate code in the application. The uncertainty of the code was evaluated by assessing several separate and integral effect tests, and for the application to actual plant Kori 3 & 4 was selected as the reference plant. Response surfaces for blowdown and reflood PCTs were generated from the results of the sensitivity analyses and probability distribution functions were established by random sampling or Monte-Carlo method for each response surface. Final uncertainties were quantified at 95% probability level and safety margins for large break LOCA were discussed.