• Journal of Practical Agriculture & Fisheries Research
• /
• v.11 no.1
• /
• pp.35-51
• /
• 2009

Three different Cordyceps militaris(Paecilomyces tenuipes and Cordyceps militaris from grain or pupae) were analysed for their chemical composition, fatty acids composition and the concentration of amino acids, cordycepin and heavy metal to obtain basic information on them as feed supplements for livestock. The crude protein content of C. militaris from grain and pupae was 76.16 and 75.45%, respectively, being higher than that of P. tenuipes(57.21%). The concentration of linoleic acid was much higher but that of linolenic acid was much lower for C. militaris from grain than for the others. The cordycepin content was significantly higher for C. militaris from grain than for that from pupae (1.64% vs 0.68% on a DM basis). But cordycepin was not detected in P. tenuipes. Heavy metal contents(Cr, Pb, Cd, Hg) for all C. militaris were below the allowance levels recommended by Ministry of Agriculture and Forestry in Republic of Korea.

• Korean journal of applied entomology
• /
• v.47 no.3
• /
• pp.273-286
• /
• 2008

Road-map for the environmental friendly integrated pest management(IPM) of insect pests was drawn up on the strawberry vinyl-houses of farmer's field. Major insect pests were occurred Tetranychus urticae and Aphis gossypii during the strawberry plant seeding in the vinyl house and open field. Also, same insect pests were occurred in the vinyl house during harvesting season of strawberry. For the control of T. urticae and A. gossypii, Phytoseiulus persimilis and Aphidius colemani as natural enemies were input to the vinyl house, respectively. However, because these natural enemies could not control insect pest populations, acaricide and insecticide were sprayed. Then natural enemies were input again in the vinyl house. Natural enemies could not endure the intense cold and differences of temperature and relative humidity between day and night during strawberry harvesting season. So, their behavior and control activity of pests were more decrease than pests. Firstly, natural enemies are input in the vinyl house during the early breeding season of strawberry, secondly, acaricides and insecticide are sprayed for the control of mites and aphids, respectively, during the middle breeding season in the hard winter. Finally, natural enemies are re-input in the vinyl house during the middle and late breeding season.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.6
• /
• pp.407-410
• /
• 2018

As the operating frequency of an electromagnetic wave increases, the maximum output and wavelength of the wave decreases, so that the size of the circuit cannot be reduced. As a result, the fabrication of a circuit with high power (of the order of or greater than kW range) and terahertz wave frequency band is limited, due to the problem of circuit size, to the order of ${\mu}m$ to mm. In order to overcome these limitations, we propose a source design technique for 0.1 THz~0.3 GW level with cylindrical shape (diameter ~2.4 cm). Modeling and computational simulations were performed to optimize the design of the high-power electromagnetic sources based on Cherenkov radiation generation technology using the principle of plasma wakefield acceleration with ponderomotive force and artificial dielectrics. An effective design guideline has been proposed to facilitate the fabrication of high-power terahertz wave vacuum devices of large diameter that are less restricted in circuit size through objective verification.

• Pediatric Infection and Vaccine
• /
• v.4 no.1
• /
• pp.116-125
• /
• 1997

Purpose : Studies on the duration of immune response against Japanese encephalitis virus from recipients with JE vaccine (Nakayama-NIH strain) in Korea. Methods : To determinate the immune response and the duration of antibody against JE vaccine, 213 students were examined since 1994 using hemmaglutination inhibition test and plaque reduction neutralization test (PRNT). Results : 24 months after the first vaccination, haemmaglutination inhibition and neutralizing antibody maintained from the recipients 63.4% (>1:20) and 100% (>1:20), respectively. In April 1996, one dose booster to the same recipients those who were vaccinated in 1994, the GMT antibody for HI and PRNT titer were both increased from 1:11.6 to 1:13.2 and 1:275.7 to 1:348.1, respectively, after 6 months booster (after 30 months from the initial vaccination). This results showed that the antibody from the active immunity could be maintained more than 12 months after the initial vaccination. On the basis of these results, inactivated killed JE vaccine (Nakayama-NIH strain) using for preventing against JE purpose seems to produce antibody enough to protect against JE at present. Conclusions : Along with the results of this study demonstrating duration of antibody, the active immunization could be maintained as long as by initial vaccination of 2 doses, a single dose of booster vaccination made during a period of 1 month to 12 months and the successive booster vaccination by 2 or 3 year intervals. However, the immunization schedule should be concerned with both epidemiology of disease and the immune response of vaccinated individuals.

• Journal of Bio-Environment Control
• /
• v.25 no.4
• /
• pp.225-231
• /
• 2016

Glasshouse heating package technologies to improve energy usage efficiency in winter were developed. Heating package was composed of the ground water source heat pump with heating capacity of 105kW, the aluminum multi-layer thermal curtain with six layers of different materials and the root zone local heater with XL pipes of ${\phi}20mm$. Venlo type glasshouse($461m^2$) with the heating package was compared with the same type and area control glasshouse with the light oil boiler, the usual non-woven fabric thermal curtain with respect to the glasshouse inside temperature, relative humidity, crop growth, and heating energy consumption. The results of test in paprika cultivation glasshouses showed that the air temperature inside glasshouse with aluminum multi-layer thermal curtain was maintained $2.2^{\circ}C$ higher than that of control glasshouse in un-heating night time and the temperature in bed with root zone local heating was $4.7^{\circ}C$ higher than that in bed without local heating. Average heating coefficient of performance(COP) of the ground water source heat pump used in paprika cultivation was 3.7 and the glasshouse inside temperature was maintained at $21^{\circ}C$ of heating set up temperature. The heating energy consumptions per 10a were measured at 14,071L of light oil and 364kWh of electric power for the control glasshouse and 35,082kWh for the glasshouse applied heating package. As results, the heating cost of the glasshouse applied heating package was 87 percent lower than that of control glasshouse. The growths of paprika in glasshouses of control and applied heating package did not show any significant difference.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.1
• /
• pp.3293-3301
• /
• 1974

An experimental work was conducted by using a laboratory-made model dryer to investigate the effect of the rate of natural forced-air on the drying rate of rough rice which was deposited in the deep-bed. The dryer consisted of 8 cylinderical containers with grain holding screen at their bottoms, each of which having 30cm in diameter and 15cm in height. The containers were sacked vertically with keeping them air-tight by using paper tape during dryer operation. Two separate layers of containers were operated in the same time to have two replications. The moisture contents of grains within each bins after predetermined period of dryer operation were determined indirectly by measuring the weight of the individual containers. The air-rates were maintained at 6 levels, or 5, 8, 10, 15, 18 and 20 millimenters of static head of water. The roomair conditions during dryer operation were maintained in the range of 10-l5$^{\circ}C$ in temperature and 40-60% in relative humidity. The results of the study are summarized as follows: 1. Drying characteristics of the grains in the bottom layers were approximately the same regardless of airdelivery rates, giving the average drying rate as about 0.35 percent per hour after 40-hour drying period, during which moisture content (w. b.) reduced from 24 percent to about 10 percent. 2. After about 40-hour drying period, the mean drying rates increased from 0.163 percent per hour to 0.263 percent per hour as air-flow rates increased from 5mm to 87.16mm of static head of water. In the same time, the moisture differences of grains between lower and upper layers varied from 12.7 percent at the air rate of 5mm of water head to 7.5 percent at the air-flow rate of 20mn of water head. Thus, the greater the air-flow rate was, the more overall improvement in drying performance was. Additionally, from the result of ineffectiveness of drying grain positioned at 70cm depth or above by the air rate of 5mm of static head of water it may be suggested in practical application that the height of grain deposit would be maintained adequately within the limits of air-rates that may be actually delivered. 3. Drying after layer-turning operation was continued for about 30 hours to test the effectiveness of reducing moisture differences in the thick layers. As a result of this layer-turning operation, moisture distribution through layers approached to narrow ranges, giving the moisture range as about 7 percent at air-flow rate of 5mm head of water, about 3 percent at 10mm head about 2 percent at 15mm head, and less than 1 percent at 20mm head. In addition, from the desirable results that drying rate was rapid in the lower layers and dully in the upper layers, layer-turning operation may be very effective in natural air drying with deep-layer grain deposit, especially when the forced air was kept in low rate. 4. Even though the high rate of air delivery is very desirable for deep-layer natural-air drying of rough rice, it can be happened that the required air delivery rate could not be attained because of limitation of power source available on farms. To give a guide line for the practical application, the power required to perform the drying with the specified air rate was analyzed for different sizes of drying bin and is given in Table (5). If a farmer selects a motor of which size is 1 or {{{{1 { 1} over {2 } }}}} H.P. and air-delivery rate which ranges from 8~10mm of head, the diameter of grain bin may be suggested to choose about 2.4m, also power tiller or other moderate size of prime motor may be recommended when the diameter of grain bin is about 5.0m or more for about 120cm grain deposit.

• Korean journal of applied entomology
• /
• v.16 no.3 s.32
• /
• pp.163-170
• /
• 1977

Potato diseases, especially mosaics and leaf roll, appear to reduce potato yield in Korea more than any other factor. A seed potato certification program was established at the Alpine Experiment Station (AES) in 1961 to produce high quality seed potatoes for distribution to Korean farmers. The present program for production of certified seed of Namjak (Irish Cobbler), the only variety recommended for spring plantings, is outlined. In 1976, approximately 10,000 MT of certified grade Namjak seed was produced by members of two Seed Producers Cooperatives in the Daekwanryeong area for distribution by the Office of Seed Production and Distribution (OSPD). The seed was inspected and certified by officers of the National Agricultural Products Inspection Office (NAPIO). Although the quality of the certified seed is far superior to that used by many farmers, the supply planted less than 1/5 of the 1977 potato crop. Certified seed of Shimabara, the variety recommended for autumn plantings, is not produced in Korea. The yield response of virus infected seed to improved cultural practices is poor. Therefore, an increase in potato acreage and yields appears to be possible only if more good quality seed is used by Korean farmers. A two or three fold increase in seed supply would be desirable. The volume of seed could be increased by expanding the production area and by improving yield in seed fields. More land is available in the alpine area and good seed potatoes could be grown in other parts of Korea. Planting better quality seeds and using better cultural pracitces would improve seed yields. Several techniques could be used to improve the quality of elite seed produced at AES. Changes in seed potato certification program should be made so that healthy seed stocks of new varieties can be released rapidly.

• The korean journal of orthodontics
• /
• v.26 no.2 s.55
• /
• pp.233-244
• /
• 1996

The purpose of this study was to compare the shear bond strength obtained from ceramic and plastic brackets bonded with various light-cured adhesives and to evaluate their debonded failure sites. Plastic brackets, Transcend 6000, Signature and Starflre TMB brackets were bonded with Orthobond, Light Bond and Transbond on one hundred forty extracted human premolar teeth as manufacturer's descriptions. After thermocycling the brackets were debonded with an Instron universal testing machine and the debonded bracket base surfaces were inspected under stereoscope to evaluate the failure sites. Also the shear bond strength and failure patterns with different curing time and with two different source of light were compared. The results were as follows. 1. There were no statistically significant differences among the mean shear bond strength of Orthobond, Light Bond and Transbond in a same bracket group except Plastic bracket group(p<0.05). 2. The mean shear bond strength of each adhesive with different bracket groups showed statistically significant differences. Stafire TMB showed the highest shear bond strenght among the brackets in this study, but there was no statistically singnificant difference with Transcend 6000 while there was statistically significant difference with Signature.(p<0.05) 3. The various bonding failure patterns were occurred among different bracket groups but most of failure sites were bracket base -adhesive interfaces. 4. There were no statistically significant differences in shear bond strength between the groups with curing time of 10 second and 20 second, and between the groups with two different sources of light as long as sufficient light intensity(above $400mWcm^2$) were provided(p<0.05). According to the result, it should be considered in clinical use of ceramic bracket with light-cured adhesives that the shear strengths of ceramic brackets were influenced by the retention from of bracket base as well as the composition of bracket and there was no difference in the shear bond strenght among various light-cured adhesives used in this study.

• Korean Journal of Cleft Lip And Palate
• /
• v.7 no.1
• /
• pp.25-34
• /
• 2004

The present study was carried out to investigate the change of the palatal length after palatoplasty in congenital cleft palate. With the data from one hundred and twelve patients with cleft palate who had been treated at the Department of Oral and Maxillofacial Surgery of Chonnam University Hospital over a period of 10 years(April 1995 to April 2004). The epidemiological characteristics, the method of palate repair, the postoperative complications and the extent of palatal lengthening were investigated and analyzed statistically. Incomplete cleft palate occurs more frequently than complete cleft palate. Male were affected 2.1 times more than female in complete cleft palate, and female were affected 1.2 times more than male in incomplete cleft palate. Dorrance method and Wardill V-Y method were frequently used in repair of incomplete cleft palate. Wardill V-Y method, Furlow double opposing Z-plasty, two flap method, and Perko method were widely used in repair of complete cleft palate. The extent of palatal lengthening was greater in the incomplete cleft palate group(5.84 mm) than in the complete cleft palate group(4.71 mm), and in the Furlow double opposing Z-plasty group(5.70 mm) than in the push back palatoplasty group(5.33 mm). But no significant difference was noted. Palatal fistula and wound dehiscence were popular postoperative complications in cleft palate. These results indicate that the extent of palatal lengthening, which contributing to speech function, is a range of 3.5% to 24.0%(average 10.8%) after palatoplasty in cleft palate patients.

• Journal of the Korean Vacuum Society
• /
• v.19 no.3
• /
• pp.211-216
• /
• 2010

The luminescence properties of $In_{0.5}Ga_{0.5}As/In_{0.5}Al_{0.5}As$ multiple quantum wells (MQWs) grown on $In_{0.5}Al_{0.5}As$ buffer layers have been studied by using photoluminescence (PL) and time-resolved PL measurements. A$1-{\mu}m$ thick $In_{0.5}Al_{0.5}As$ buffer layers were deposited on a 500 nm thick GaAs layer, followed by the deposition of the InGaAs/InAlAs MQWs. In order to investigate the effects of InAlAs buffer layer on the optical properties of the MQWs, four different temperature sequences are used for the growth of InAlAs buffer layer. The growth temperature for InAlAs buffer layer was varied from 320^{\circ}C to $580^{\circ}C$. The MQWs consist of three $In_{0.5}Ga_{0.5}$As wells with different well thicknesses (2.5 nm, 4.0 nm, and 6.0 nm thick) and 10 nm thick $In_{0.5}Al_{0.5}$As barriers. The PL spectra from the MQWs with InAlAs layer grown at lower temperature range ($320-580^{\circ}C$) showed strong peaks from 4 nm QW and 6 nm QW. However, for the MQWs with InAlAs buffer grown at higher temperature range ($320-480^{\circ}C$), the PL spectra only showed a strong peak from 6 nm QW. The strongest PL intensity was obtained from the MQWs with InAlAs layer grown at the fixed temperature of $480^{\circ}C$, while the MQWs with buffer layer grown at higher temperature from $530^{\circ}C$ to $580^{\circ}C$ showed the weakest PL intensity. From the emission wavelength dependence of PL decay times, the fast and slow decay times may be related to the recombination of carriers in the 4 nm QW and 6 nm QW, respectively. These results indicated that the growth temperatures of InAlAs layer affect the structural and optical properties of the MQWs.