• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.333-336
• /
• 2006

High Pressure Annealing System was developed to improve the characteristics of low-temperature poly-silicon thin film transistors.. (TFTs). The high-pressure steam annealing was applied to the poly-silicon film made by rapid thermal annealing method. The carrier lifetime was investigated by Microwave detection of the Photo-Conductive Decay and the increase of carrier lifetime which indicates the reduction of the defect was observed by high-pressure steam annealing of 1MPa 600C 1hour.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권6호
• /
• pp.235-240
• /
• 2003

In this paper, we present the fabrication and the characteristic analysis of sequential lateral solidification(SLS) poly-Si thin film transistors(TFT's) with molybdenum gate for active matrix liquid displays (AMLCD's) pixel controlling devices. The molybdenum gate is applied for the purpose of low temperature processing. The maximum processing temperature is 55$0^{\circ}C$ at the dopant thermal annealing step. The SLS processed poly-Si film which is reduced grain and grain boundary effect, is applied for the purpose of electrical characteristics improvements of poly-Si TFT's. The fabricated low temperature SLS poly-Si TFT's had a varying the channel length and width from 10${\mu}{\textrm}{m}$ to 2${\mu}{\textrm}{m}$. And to analyze these devices, extract electrical characteristic parameters (field effect mobility, threshold voltage, subthreshold slope, on off current etc) from current-voltage transfer characteristics curve. The extract electrical characteristic of fabricated low temperature SLS poly-Si TFT's showed the mobility of 100~400cm$^2$/Vs, the off current of about 100pA, and the on/off current ratio of about $10^7$. Also, we observed that the change of grain boundary according to varying channel length is dominant for the change of electrical characteristics more than the change of grain boundary according to varying channel width. Hereby, we comprehend well the characteristics of SLS processed poly-Si TFT's witch is recrystallized to channel length direction.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.785-789
• /
• 2005

Low temperature deposition of silicon and silicon nitride films by catalytic CVD technique was studied for application to thin film transistors on plastic substrates for flexible AMOLEDs. The substrate temperature initially held at room temperature, and was controlled successfully below $150^{\circ}C$ during the entire deposition process. Amorphous silicon films having good adhesion, good surface morphology and sufficiently low content of atomic hydrogen were obtained and could be successfully crystallized using excimer laser without a prior dehydrogenation step. $SiN_x$ films showed a good refractive index, a high deposition rate, a moderate breakdown field and a dielectric constant. The Cat-CVD silicon and silicon nitride films can be good candidates for fabricating thin films transistors on plastic substrates to drive active-matrix organic light emitting display.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.305-308
• /
• 2004

We present a novel process for the ultra low temperature (<150$^{\circ}C$) polycrystalline silicon (ULTPS) TFT for the flexible display applications on the plastic substrate. The sequential lateral solidification (SLS) was used for the crystallization of the amorphous silicon film deposited by rf magnetron sputtering, resulting in high mobility polycrystalline silicon (poly-Si) film. The gate dielectric was composed of thin $SiO_2$ formed by plasma oxidation and $Al_2O_3$ deposited by plasma enhanced atomic layer deposition. The breakdown field of gate dielectric on poly-Si film showed above 6.3 MV/cm. Laser activation reduced the source/drain resistance below 200 ${\Omega}$/ㅁ for n layer and 400 ${\Omega}$/ㅁ for p layer. The fabricated ULTPS TFT shows excellent performance with mobilities of 114 $cm^2$/Vs (nMOS) and 42 $cm^2$/Vs (pMOS), on/off current ratios of 4.20${\times}10^6$ (nMOS) and 5.7${\times}10^5$ (PMOS).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1427-1429
• /
• 2001

Polycrystalline silicon(poly-Si) films are deposited on low temperature glass substrate by Hot-Wire CVD(HWCVD). The structural properties of the poly-Si films are strongly dependent on the wire temperature($T_w$). The films deposited at high $T_w$ of 2000$^{\circ}C$ have superior crystalline properties; average lateral grain sizes are larger than $1{\mu}m$ and there at·e no vertical grain boundaries. The surface of the high $T_w$ samples are naturally textured like pyramid shape. These large grain size and textured surface are believed to give high current density when applied to solar cells. However, the poly-si films are structurally porous and contains high defect density, by which high concentration of C and O resulted within the films by air-penetration after removed from chamber.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.495-498
• /
• 2006

The influence of various process parameters for the as-deposited poly silicon was investigated. The polycrystalline silicon films were successfully deposited on glass substrates at a low-temperature $(<200^{\circ}C)$ using the catalytic chemical vapor deposition (Cat-CVD). We achieved a low hydrogen content $({\sim}0.9%)$ and a high deposition rate $({\sim}35{\AA}/sec)$. The film is applicable to thin film transistors on plastic substrates.

• 한국재료학회지
• /
• 제22권4호
• /
• pp.190-194
• /
• 2012

The formation of high-quality polycrystalline silicon (poly-Si) on relatively low cost substrate has been an important issue in the development of thin film solar cells. Poly-Si seed layers were fabricated by an inverse aluminum-induced crystallization (I-AIC) process and the properties of the resulting layer were characterized. The I-AIC process has an advantage of being able to continue the epitaxial growth without an Al layer removing process. An amorphous Si precursor layer was deposited on Corning glass substrates by RF magnetron sputtering system with Ar plasma. Then, Al thin film was deposited by thermal evaporation. An $SiO_2$ diffusion barrier layer was formed between Si and Al layers to control the surface orientation of seed layer. The crystallinity of the poly-Si seed layer was analyzed by Raman spectroscopy and x-ray diffraction (XRD). The grain size and orientation of the poly-Si seed layer were determined by electron back scattering diffraction (EBSD) method. The prepared poly-Si seed layer showed high volume fraction of crystalline Si and <100> orientation. The diffusion barrier layer and processing temperature significantly affected the grain size and orientation of the poly Si seed layer. The shorter oxidation time and lower processing temperature led to a better orientation of the poly-Si seed layer. This study presents the formation mechanism of a poly seed layer by inverse aluminum-induced crystallization.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1997년도 한국재료학회 추계학술발표회
• /
• pp.85-85
• /
• 1997

• 반도체디스플레이기술학회지
• /
• 제6권2호
• /
• pp.15-18
• /
• 2007

Effects of $O_2$ flow during deposition on Si crystallization at low substrate temperature were studied. Silicon thin films were prepared on $SiO_2$ substrates in a low-pressure chemical vapor deposition chamber using a mixture of $SiH_4$ and $H_2$. In some cases $O_2$ was intentionally introduced during deposition. Growth of poly silicon was observed at the substrate temperature as low as $480^{\circ}C$ when $O_2$ was flowed during deposition implying that crystallization of Si was enhanced by $O_2$ flow. On the other hand, $O_2$ flow did not show any significant effects at higher substrate temperature, where deposition rate is relatively fast. Enhancement mechanism of Si crystallization by $O_2$ flow was suggested from these results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 디스플레이 광소자분야
• /
• pp.173-176
• /
• 2004

In this study we investigated post ELA(Excimer Laser Annealing) effect on SMC (Silicide Mediated Crystalization) poly-Si (Polycrystalline Silicon) to improve the characteristics of poly-Si. Combining SMC and XeCl ELA were used to crystallize the a-Si (amorphous Silicon) at various ELA energy density for LTPS (Low Temperature Polycrystalline Silicon). We fabricated the conventional SMC poly-Si with no SPC (Solid Phase Crystallization) phase using UV heating method[1] and irradiated excimer laser on SMC poly-Si, so called SMC-ELA poly-Si. After using post ELA we can get better surface morphology than conventional ELA poly-Si and enhance characteristics of SMC poly-Si. We also observed the threshold energy density regime in SMC-ELA poly-Si like conventional ELA poly-Si.