A key point of a soldering process for photovoltaic (PV) modules is to increase an adhesive strength leading a low resistivity between ribbon and cell. In this study, we intended to optimize a heating condition for the soldering process and characterize the soldered joint via physical and chemical analysis methods. For the purpose, the heating conditions were adjusted by IR lamp power, heating time and hot plate temperature for preheating a cell. Since then the peel test for the ribbon and cell was conducted, consequently the peel strength data shows that there is some optimum soldering condition. In here, we observed that the peel strength was modified by increasing the heating condition. Such a soldering property is affected by a various factors of which the soldered joint, flux and bus bar of the cell are changed on the heating condition. Therefore, we tried to reveal causes determining the soldering property through analyzing the soldered interface.
COMS (Communication, Ocean and Meteorological Satellite) is a geostationary satellite and has been developing by KARI for communication and ocean and meteorological observations. It will be launched by ARIANE 5. Ka-band components are installed on South panel, where single solar array wing is mounted. Radiators, embedded heat pipes, external heat pipe, insulation blankets and heaters are utilized for the thermal control of the satellite. The Ka-band payload section is divided several areas based on unit operating temperature in order to optimize radiator area and maximize heat rejection capability. Other equipment for sensors and bus are installed on North panel. The ocean and meteorological sensors are installed on optical benches on the top floor to decouple thermally from the satellite. During the transfer orbit operation, satellite will be under severe thermal environments due to low dissipation of components, satellite attitudes and LAE(Liquid Apogee Engine) firing. This paper presents temperature and heater power prediction and validation of thermal control design during transfer orbit operation.
본 논문은 MBOA UWB SoC의 MAC 시스템 설계에 관한 것이다. 구현된 MBOA MAC 알고리즘은 일반적으로 널리 사용되고 있는 중앙의 마스터가 네트워크를 관리하는 방식이 아니라, 모든 디바이스가 네트워크를 구성하고 관리할 수 있는 분산 방식을 사용하고 있다. 따라서 MAC이 분산 네트워크를 구성하고 관리를 하기 때문에 메쉬 네트워크 구성이 용이하다. 시스템은 데이터 처리 속도를 최대화하기 위해서 캐쉬가 내장된 ARM926EJ를 내장하였고, 재사용 및 시스템 설계가 용이한 AMBA 버스를 사용하였다. 또한, 칩의 소모 전력을 최소화하기 위해 시스템 클럭 제어 알고리즘을 구현하였다. 그리고, 시스템 메모리 버퍼와 MAC 하드웨어간의 데이터 이동을 위하여 MAC 전용 DMA를 설계하였으며, Host와 시스템 메모리 버퍼간의 고속의 데이터 이동을 위하여 USB 2.0 블록의 전용 DMA를 사용하였다.
CNUSAIL-1은 태양돛을 탑재한 3U크기의 큐브위성이다. 주 임무는 저궤도에서 태양돛을 전개하는 것이며, 추가적으로 태양돛 전개와 태양돛 운용에 따른 위성의 자세/궤도변화를 확인하는 임무를 수행한다. 이를 위해, 위성의 각 시스템은 위성의 동적 데이터와 태양돛 작동 사진을 수집하고 지상국으로 전송한다. 본 논문에서는 이와 같은 임무를 수행하는 CNUSAIL-1의 태양돛 임무를 소개하고 시스템 개념설계 결과를 나타낸다. 탑재체인 태양돛의 구동 및 운용 원리를 구현하고, 버스시스템을 자세제어계, 통신계, 전력계, 명령 및 데이터 처리계, 구조 및 열 제어계로 나누어 개념 설계를 수행한다.
본 논문에서는 USB(Universal Serial Bus) 케이블 전원선에서의 방사성 EMI(Electro-Magnetci Interference) 개선 방안을 제시한다. 케이블 전원선에서의 EMI 방사현상을 확인하기 위해 무선 비디오 액세스 시스템을 이용하여, 방사성 EMI 결과를 분석하고 초기 측정 결과 규제치 대비 약 3 [dBuV/m]~15 [dBuV/m]를 초과함을 확인한다. 방사성 EMI 원인 분석을 위해, 먼저 USB 케이블 전원선에서의 S-파라미터 측정을 수행하여 케이블의 고주파수 대역에서의 규칙적인 공진현상과 방사성 EMI 주파수의 연관성을 분석한다. 그리고, 전원 회로 임피던스 관리 기법을 응용하여 캐패시터의 개수 선정, 비드를 이용한 저역통과 대역 필터를 구성을 통해 케이블 전원선의 공진현상을 저감하는 개선방법을 적용한다. 결론적으로 개선된 회로를 시스템에 적용하여 케이블의 규칙적 공진의 저감방법을 제시하여, 방사성 EMI 테스트 결과 규제치 대비 약 3 [dBuV/m]~20 [dBuV/m] 마진의 마진을 확보하여 제시한 방법의 적합성 확인한다.
The Terra-Scope system is an affordable 4-D down-hole seismic monitoring system based on independent, microprocessor-controlled sensor Pods. The Pods are nominally 50 mm in diameter, and about 120 mm long. They are expected to cost approximately $6000 each. An internal 16-bit, extremely low power MCU controls all aspects of instrumentation, eight programmable gain amplifiers, and local signal storage. Each Pod measures 3-D acceleration, tilt, azimuth, temperature, and other parametric variables such as pore water pressure and pH. Each Pod communicates over a standard digital bus (RS-485) through a completely web-based GUI interface, and has a power consumption of less than 400 mW. Three-dimensional acceleration is measured by pure digital force-balance MEMS-based accelerometers. These accelerometers have a dynamic range of more than 115 dB and a frequency response from DC to 1000 Hz with a noise floor of less than $30ng_{rms}/{\surd}Hz$. Accelerations above 0.2 g are measured by a second set of MEMS-based accelerometers, giving a full 160 dB dynamic range. This paper describes the system design and the cooperative shared-time scheduler implemented for this project. Restraints accounted for include multiple data streams, integration of multiple free agents, interaction with the asynchronous world, and hardened time stamping of accelerometer data. The prototype of the device is currently undergoing evaluation. The first array will be installed in the spring of 2006.
This paper presents a developing procedure of the CAN-based real-time simulator for car body control, aiming at replacing the actual W/H (Wiring Harness) and J/B(Junction Box) couple eventually. The CAN protocol, as one kind of field-bus communication, defines the lowest 2 layers of the ISO/OSI standard, namely, the physical layer(PL) and the data link layer(DLL), for which the CSMA/NBA protocol is generally adopted. For CPU, two PIC18Fxx8x's are used because of their built-in integration of CAN controller, large internal FLASH memory (48K or 64K), and their costs. To control J/B's and actuators, 2 controller boards are separately implemented, between which CAN lines communicate through CAN transceivers MCP255. A power motor for washing windshield, 1 door lock motor, and 6 blink lamps are chosen for actuators of the simulator for the first stage. For the software architecture, a polling method is used for the fast global response time despite its slow individual response time. To improve the individual response time and to escape from some eventual trapped-function loops, High/Low ports of the CPU are simply used, which increases the stability of the actuator modules. The experimental test shows generally satisfactory results in normal transmitting / receiving function and message trace function. This simulator based on CAN shows a promising usefulness of lighter, more reliable and intelligent distributed body control approach than the conventional W/H and J/B couple. Another advantage of this approach lies in the distributed control itself, which gives better performance in hard real-time computing than centralized one, and in the ability of integrating different modules through CAN.
유도 전동기를 전압 제어하기 위한 최적 PWM 스위칭 방법을 제시하려한다. 전압 인버터의 공간 벡터 변조 방식은 DC-버스 이용을 향상시키고 정류 손실을 감소시키기 때문에 디지털 구현의 경우 특히 선호하는 PWM 방법이다. 유도 전동기 전압 제어를 위한 최적 PWM 스위칭 방법은 제시한 최적 PWM 알고리즘을 사용하여 두 개의 활성 전압 벡터(active voltage vector)와 하나의 영 전압 벡터(zero voltage vector)로 구성하였다. 선택된 스위칭 순차 열은 변조 지수(modulation index)와 운송파(carrier wave) 주기의 함수로 정의 된다. 순차 열은 인버터 스위칭 손실과 전류 리플 값을 기준으로 사용하여 선택된다. 실험 결과 중 저 전력용으로 사용할 경우 스위칭 주파수를 증가시킴에 따라 고조파 왜곡이 감소하고 동특성이 좋아짐을 확인할 수 있었다.
H.264 영상 압축 표준은 높은 압축률과 화질로 널리 이용되고 있다. H.264 복호기는 일반적으로 마크로블록 또는 $4{\times}4$ 하위 블록 단위로 파이프라인을 적용하여 동작한다. 이러한 파이프라인 한 단의 주기는 보통 최악의 상황에서도 동작을 보장하도록 결정되어 높은 전송 대역폭과 고성능 연산기를 요구하고 연산기가 일을 하지 않고 쉬는 사이클이 많아지는 결과를 초래한다. 본 논문에서는 이러한 연산기의 쉬는 사이클을 줄이고 데이터 전송 대역폭과 연산기 성능 요구 조건을 완화시킬 수 있는 적응적 파이프라인 구조를 채택한 효율적인 영상 복호기 구조를 제안한다. 제안한 구조에서는 파라미터와 계수는 핸드셰이킹 방식으로 전용 신호선을 통해 전달되고 복호된 영상 데이터는 AMBA AHB 네트워크를 통해 메모리에 저장하거나 읽어 온다. 각 블록의 복호 처리 시간은 영상의 특성에 따라 가변적으로 변하고 각 연산기는 데이터가 준비되면 언제든지 동작을 할 수 있다. 제안한 구조에 따라 H.264 복호기를 설계하였고 FPGA를 이용하여 동작을 검증하였다.
본 논문에서는 LTE-Advanced, Software defined radio(SRD)등 4G 이동통신 핵심기술에 응용 가능한 10b 500MS/s $0.13{\mu}m$ CMOS A/D 변환기(ADC)를 제안한다. 제안하는 AD는 저전력 특성을 만족하기 위해 특별한 보정기법을 포함하지 않는 단일 채널 형태로 설계되었으며, 500MS/s의 고속 변환속도를 만족하기 위해 폴딩 신호처리 기법을 사용하였다. 또한 하위 7b ADC의 높은 folding rate(FR)을 극복하기 위해 cascaded 형태의 폴딩 인터폴레이팅 기법을 적용하였으며, 폴딩 버스에서 발생하는 기생 커패시턴스에 의한 주파수 제한 및 전압이득 감소를 최소화하기 위해 folded cascode 출력단을 갖는 폴딩 증폭기를 설계하였다. 제안하는 ADC는 $0.13{\mu}m$ lP6M CMOS 공정으로 설계되었으며 유효면적은 $1.5mm^2$이다. 시제품 ADC의 INL, DNL은 10b 해상도에서 각각 2.95LSB, 1.24LSB 수준으로 측정되었으며, 입력주파수 9.27MHz, 500MHz의 변환속도에서 SNDR은 54.8dB, SFDR은 63.4dBc의 특성을 보인다. 1.2V(1.5V)의 전원전압에서 주변회로를 포함한 전체 ADC의 전력소모는 150mW ($300{\mu}W/MS/s$)이다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.