• Clean Technology
• /
• v.21 no.4
• /
• pp.229-234
• /
• 2015

Recently, there are increasing numbers of study regarding hydrogen fuels but researches on desulfurization of diesel are rare. In this study, we performed diesel desulfurization reactor design by computation fluid dynamics simulation. By analyzing the change in flow and sulfur concentration at the outlet according to the changes in flow rate, reactor length, and reactor diameter, we have found the minimum catalyst performance for the given flow rate condition and the relation between the reactor performance and the reactor size and shape. We also studied the effects of permeability of the packed bed on the flow and sulfur concentration distribution. The present work can be utilized to design a diesel desulfurization reactor for a fuel cell used in ships. Furthermore, the present work also can be used to design low sulfur diesel supply in oil refineries and therefore contribute to the development of clean petrochemical technology.

• Fire Science and Engineering
• /
• v.30 no.1
• /
• pp.37-42
• /
• 2016

The dimensionless extinction constants of smoke particles produced from burning of soy methyl ester (B100) biodiesel and ultra low sulfur diesel (ULSD) fuels were measured. To this end, optical measurements of smoke volume fraction with the aid of a He-Ne laser at 633 nm were compared to the simultaneous gravimetric measurements. The average value of measured dimensionless extinction constants at 633 nm was 11.8 for biodiesel smoke particles and 11.1 for diesel smoke particles, respectively whose values are very comparable withing the range of measurement uncertainty (${\pm}10.1%$). The analysis of Raman spectroscopy revealed that overall characteristics of light extinction between particles produced from each fuel may differ from each other.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.1
• /
• pp.21-27
• /
• 2015

Hydrogen production from commercial diesel fuels is an attactive option for energy generation purpose due to the low cost and good availability of diesel fuels. However, in order to utilize commercial diesel fuels, the sulfur contents must be removed down to approximately 0.1 ppm level to protect the fuel cell catalysts from poisoning. Commercial catalysts $CoMo/Al_2O_3$ and $NiMo/Al_2O_3$ were tested for HDS (Hydrodesulfurization) of model diesel and commercial diesel. The experimental conditions were $250-400^{\circ}C$ and LHSV (Liquid Hourly Space Velocity) $0.27-2.12hr^{-1}$. $NiMo/Al_2O_3$ was found to be more effective than $CoMo/Al_2O_3$ in removing sulfur from model diesel. Based on the experimental results of model diesel, commercial diesel fuel purchased from a local petrol station was tested for HDS using $NiMo/Al_2O_3$. The GC-SCD (Gas Chromatography Sulfur Chemiluminescence Detector) results showed that the DMDBT (Dimethyldibenzothiophene) derivatives were fully removed from the commercial diesel fuel proving that HDS with $NiMo/Al_2O_3$ is technically feasible for industrial applications.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.3
• /
• pp.450-458
• /
• 2012

In order to reduce the effects of greenhouse gas (GHG) emissions, the South Korean government has announced a special platform of technologies as part of an effort to minimize global climate change. To further this effort, the Korean government has pledged to increase low-carbon and carbon neutral resources for biofuel derived from biomass to replace fossil and to decrease levels of carbon dioxide. In general, second generation biofuel produced form woody biomass is expected to be an effective avenue for reducing fossil fuel consumption and greenhouse gas (GHG) emissions in road transport. It is important that under the new Korean initiative, pilot scale studies evolve practices to produce biomass-to-liquid (BTL) fuel. This study reports the quality characteristics of F-T(Fischer-Tropsch) diesel for production of BTL fuel. Synthetic F-Tdiesel fuel can be used in automotive diesel engines, pure or blended with automotive diesel, due to its similar physical properties to diesel. F-T diesel fuel was synthesized by Fischer-Tropsch (F-T) process with syngas($H_2$/CO), Fe basedcatalyst in low temperature condition($240^{\circ}C$). Synthetic F-T diesel with diesel compositions after distillation process is consisted of $C_{12}{\sim}C_{23+}$ mixture as a kerosine, diesel compositions of n-paraffin and iso-paraffin compounds. Synthetic F-T diesel investigated a very high cetane number, low aromatic composition and sulfur free level compared to automotive diesel. Synthetic F-T diesel also show The wear scar of synthetic F-T diesel show poor lubricity due to low content of sulfur and aromatic compounds compared to automotive diesel.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.5
• /
• pp.85-90
• /
• 2006

Since air pollution has become a globally critical issue and exhaust emissions from automobiles cause a major source of air pollution, many countries including advanced countries have stipulated stringent emission regulations. This test was conducted on the effect of continuous regeneration diesel particulate filter and cooled-EGR, and 15ppm low sulfur diesel was used as a test fuel. Exhaust emissions, PM, NOx, CO, HC and Soots were measured and compared under D-13modes. Through durability test on diesel particulate filter, regeneration characteristics and control technology on PM were investigated in overall.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.181-185
• /
• 2014

This paper describes the effect of canola biodiesel blended fuel on the combustion and emission characteristics in a four cylinder CRDI(Common-rail direct injection) diesel engine. In this study, using the biodiesel fuel(20%,40% of biodiesel-canola oil and 80%, 60% of ULSD(ultra low sulfur diesel) by volume ratio with change of engine speed and injection pressure. The experiment results of increasing biodiesel ratio fuel show that NOx emissions increased. However, soot emission were reduced BC fuels compared to ULSD. Soot emissions largely increased at low injection pressure.

• Journal of Korean Society for Atmospheric Environment
• /
• v.14 no.4
• /
• pp.313-320
• /
• 1998

The most desirable diesel oxidation catalyst (DOC) should have the properties of oxidibing CO and HC effectively at low exhaust gas temperature while minimizing the formation of sulfate at high exhaust gas temperature. Precious metals such as platinum and palladium have been known to be sufficiently active for oxidizing CO and HC and also to have high activity for the oxidation of sulfur dioxide (SO2) to sulfor trioxide (SO3). There is a need to develop a highly selective catalyst which can promote the oxidation of CO and HC efficiently, but, on the other hand, suppress the oxidation of SO2. One approach to solve this problem is to load a base metal such as vanadium in Pt-based catalyst to suppress sulfate formation. In this study, a Pt-V catalyst was prepared by impregnating platinum and vanadium onto a Ti-Si wash coated catalyst in a laboratory reactor by changing the formulations and reaction temperatures.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.417-422
• /
• 2010

Low temperature diesel combustion was achieved via a combination of late injection timing ($8.5^{\circ}$ CA BTDC to $0.5^{\circ}$ CA BTDC) and heavy exhaust gas recirculation (37% to 48%) with ultra low sulfur Swedish diesel fuel in a 1.7L common rail direct injection diesel engine. When injection timing is retarded at a certain exhaust gas recirculation rate, the particulate matter and nitrogen oxides decease simultaneously, while the hydrocarbon and carbon monoxide increase. Hydrocarbon speciation by gas chromatography using a flame ionization detector reveals that the ratio of partially burned hydrocarbon, i.e., mainly alkenes increase as the injection timing is retarded and exhaust gas recirculation is increased. The two most abundant hydrocarbon species are ethene which is a representative species of partially burned hydrocarbons, and n-undecane, which is a representative species of unburned hydrocarbons. They may be used as surrogate hydrocarbon species for performing a bench flow reactor test for catalyst development.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.537-542
• /
• 1999

Removal of sulfur compounds in the petroleum products is essential for the prevention of sulfur oxides. However, conventional methods involving catalytic reactions are found to have some limitations in complete removal of harmful sulfur compounds and to require relatively high cost. Recently, desulfurization process using microorganisms is known to be promising in terms of excellent sulfur removal efficiency and reasonably low treatment cost. For the biodesulfurization process to be effective, the solubilization of sulfur compounds into aqueous solution is a prerequisite. In this study, polyoxyethylene nonionic surfactants were used in order to enhance the solubilization of sulfur spectrophotometer. The solubilization of sulfur compounds was found to increase with temperature and to bo abruptly increased at above 1 wt % surfactant solutions. It was also observed that the longer the hydrophobic chain of the surfactant molecule, the higher solubilizing power of a nonionic surfactant. It was found that the Tergitol series surfactants showed higher solubilizing capacity than Neodol series presumably due to the disruption of the regular packing in the hydrocarbon region of the surfactant aggregates.

• Journal of the Korean Society of Combustion
• /
• v.16 no.4
• /
• pp.1-7
• /
• 2011

The purpose of this study was to analyze the effect of pilot injection strategy on the combustion and emissions characteristics in a four cylinder common-rail direct injection diesel engine fueled with biodiesel(soybean oil) blend. The tested fuel was mixed of 20% biodiesel and 80% ULSD(Ultra low sulfur diesel) by volume ratio. The experiments were performed under two load conditions, and results were compared with those of single injection. The experimental results showed that the ignition delay of BD20 was shorter than compared to that of ULSD in the case of low load condition. Also, the fuel consumption of BD20 was more higher than that of ULSD. Fuel consumption by applied pilot injection strategy were generally decreased compared with that of single injection. In the case of pilot injection, the exhaust emissions such as CO and HC emissions were decreased compared to the single injection.