• Journal of Korean Physical Therapy Science
• /
• v.8 no.2
• /
• pp.1033-1038
• /
• 2001

This studies were to investigate the effects of low power Helium-Neon Infra-Red(He-Ne IR) laser on the changes of the chemical components in serum of the peripheral neuropathy in diabetic rats. The twenty one Spraque-Dawley adult male rats were assigned to the 3 groups: the control group(N=7), the diabetic group(n=7) and the laser group(n=7). The diabetic group was induced with a single intravenous injecion of 50mg/kg body weight streptozotocin dissolved to 0.01mol/L citrate buffer, pH 4.5. The experimental1asser group was irradiated low power He-Ne IR laser for 5 minutes every day during 21 days to the diabetic group. The results were as follows: 1. ALT was increased the laser treatment group than the diabetic group. but that was not significant. 2. AST was significantly increased the laser treatment group than the control group and the diabetic group. 3. LDH was significantly decreased the diabetic group and laser treatment group. 4. ALP was significantly increased the diabetic group and laser treatment group. 5. CHOL was significantly decreased the laser treatment group than the diabetic group. 6. TRIG was significantly increased the laser treatment group than the diabetic group. 7. CPK was significantly increased the laser treatment group than the control group and the diabetic group.

• Journal of Welding and Joining
• /
• v.24 no.4
• /
• pp.32-38
• /
• 2006

The objective of present research works is to investigate the effects of process parameters, including the power of laser, cutting speed, material thickness, and the edge angle, on the melted area in the sharp edge of the cut material fur the case of cutting of a low carbon steel sheet using high-power CW Nd:YAG laser. In order to investigate the influence of edge angle and size of loop on the melted area in the sharp edge, angular cutting tests and loop cutting tests have been carried out. From the results of angular cutting tests, the relationship between the edge angle and the melted area has been obtained. The results of the experiments have been shown that the melted area is rapidly reduced from $120^{\circ}$ of the edge angle and the melted area is nearly zero at $150^{\circ}$ of the edge angle. Through the results of loop cutting experiments, the relationship between the cutting angle on the melted area in the edge according to the size of loop have been obtained. In addition, it has been shown that a proper size of loop is nearly 3 mm as the corner angle is greater than $90^{\circ}$ and 5 mm as the comer angle is less than $90^{\circ}$. The results of above experiments will be reflected on the knowledge base to generate optimal cutting path of the laser.

• The korean journal of orthodontics
• /
• v.18 no.2
• /
• pp.435-447
• /
• 1988

This study was performed to evaluate the effect of low-power laser irradiation on the periodontium of the orthodontically moved tooth of rat. The experimental materials were 30 male rats. Orthodontic appliances were placed bilaterally between maxillary first molar and incisor teeth and the force was 1 Oz. Experimental animals were divided into eight groups as follows: no movement, 1st, 2nd, 3rd, 5th, 7th, 14th, and 28th day groups. In all experimental animals except no movement group, low-power laser was irradiated on the unilateral maxillary first molar (experimental side), but on the contralateral side, only orthodontic force was applied (control side). The histologic effects of laser on the periodontium of the orthodontically moved tooth on the consecutive experimental days were as follows: In the experimental side, by the biostimulating effect of laser, 1. Hyalinized tissue was formed later and eliminated earlier than in the control side. 2. Undermining bone resorption was occurred earlier than in the control side. 3. More osteoid tissue was deposited and calcified earlier than in the control side. 4. The most prominent changes were formation of new blood vessels and dilatation of old blood vessels.

• Journal of Oral Medicine and Pain
• /
• v.10 no.1
• /
• pp.91-104
• /
• 1985

In order to study the effects of the low power density laser (AsGa) on the wound healing of tongue and skin, thirty two healthy rats were anesthetized with pentothal. The tongue wound, approximately 1 mm in depth and 2mm in diameter, was created on the anterior of the tongue and the skin wound, approximately, 2mm in depth and 6-8mm in diameter, was created on the back of rat with the tip of small rongeur forcep. Wounds of experimental groups were irradiated with AsGa laser (Stomalaser, SEDATELEC Co., France) every other day by ninth day. The areas of wounds were measured at 1, 3, 5, 7, 9 days after wounding and the specimens were sectioned, stained, and observed with light microscope. The results were as follows : 1. In the AsGa laser irradiated wound of tongue, the epithelial and fibroblastic regeneration were accelerated when compared with controls. 2. In the AsGa laser irradiated wound of skin, the epithelial and fibroblastic regeneration were accelerated when compared with controls. 3. When the wound areas were compared, there was a significant difference between control group and experimental group (P < 0.01: 2-Way NOVA).

• Journal of Welding and Joining
• /
• v.29 no.4
• /
• pp.80-84
• /
• 2011

In the 5xxx series Al-Mg alloy, magnesium addition can increase the strength of aluminum alloy by solid solution strengthening but it has a relatively low melting and boiling temperature. During full -penetration laser welding of the Al-Mg alloys, its low boiling point and high vapor pressure brings about the spiky humping bead on the bottom side. Under back-side shielding, the spiking of back bead can be reduced but it restraints the process flexibility. In this study, a square pulse waveform modulation was employed to stabilize keyhole and back bead surface without back-side shielding. By using an experimental design, the bead shapes were evaluated for various process parameters such as the focal position, welding velocity and waveform parameters and the smooth back bead shape could be achieved.

• Journal of Oral Medicine and Pain
• /
• v.12 no.1
• /
• pp.17-26
• /
• 1987

In order to investigate the biostimulatory effect of low power density laser radiation in vitro, human gingival fibroblasts were cultured in MEM in which experiment groups respectively were made to 30 sec, 60 sec and 90 sec group. The experiments were performed by cell count, DNA and protein content measurements after experimental groups were irradiated with GaAlAs laser every day by forth day and then control group and experimental groups were compared. The results were as follows: 1. Cell counts of experimental groups were increased with exposure time, but showed no significance (P>0.05). 2. When the protein contents were compared, there was a very significant increase in 90 sec. experimental group (P<0.01). 3. When the DNA contents were compared, there was a significant difference only between control and 70 sec. group (P<0.05).

• ETRI Journal
• /
• v.25 no.4
• /
• pp.247-252
• /
• 2003

This paper presents results from experiments on laser-annealed SiGe-selective epitaxial growth (LA-SiGe-SEG). The SiGe-SEG technology is attractive for devices that require a low band gap and high mobility. However, it is difficult to make such devices because the SiGe and the highly doped region in the SiGe layer limit the thermal budget. This results in leakage and transient enhanced diffusion. To solve these problems, we grew in situ doped SiGe SEG film and annealed it on an XMR5121 high power XeCl excimer laser system. We successfully demonstrated this LA-SiGe-SEG technique with highly doped Ge and an ultra shallow junction on p-type Si (100). Analyzing the doping profiles of phosphorus, Ge compositions, surface morphology, and electric characteristics, we confirmed that the LA-SiGe-SEG technology is suitable for fabricating high-speed, low-power devices.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.8 s.173
• /
• pp.17-26
• /
• 2005

Dissimilar-metal welds(DHWs) are used widely in various industrial applications due to the pratical importance from the technical and economic aspect. However, DMWs have several fabricative and metallurgical drawbacks that can often lead to in-service failures. For example, the most pronounced fabrication faults are hot cracks. Recently, DMWs have used the various of heat source to decrease such as faults. In this paper, the weldability on dissimilar metal welds of Austenite stainless steel and Low carbon steel using a continuous wave Nd:YAG laser was experimentally investigated. Experiments were conducted to determine effects of welding parameters, on eliminating or reducing the extent welding zone formation at dissimilar metal welds and to optimize those parameters that have the most influence parameters such as focus length, power, beam speed, shielding gas, and wave length of laser.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1060-1062
• /
• 1999

Pulsed Nd:YAG laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. And the parallel mesh is added to increase laser output power. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition, we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the parallel mesh and the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 10pps to 110pps by the step of 20pps at 1000V and 1200V, it is found that the laser efficiency decreases but the laser output power increases about 5W at each step.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.12
• /
• pp.1055-1060
• /
• 2016

Laser welding is a high-density energy welding method. Hence, deep penetration and high welding speed can be realized with lower heat input as compared with conventional welding. The heat input of a CW laser welding is determined by laser power and welding speed. In this study, bead and lap welding of $0.5mm^t$ pure titanium was performed using a fiber laser. Its weldability with laser power and welding speed was evaluated. Penetration, bead width, joining length, and bead shape were investigated, and the mechanical properties were examined through tensile-shear strength tests. Welds with sound joining length were obtained when the laser power and welding speed were respectively 0.5 kW and 2.5 m/min, and 1.5 kW and 6 m/min, and the weld obtained at low output presented better ductility than that obtained at high output.