• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.297-303
• /
• 2018

With the changing trend of the building construction to high rising and large scaling, the underground structure has been increased, and its usage also increased and variety. Hence, to protect the underground structure against underground water, various water proofing methods has been developed. Among the many water proofing methods, the combined water proofing method using both asphalt seal and sheet has been widely used to secure the sufficient performance and decrease the construction failure. However, during the summer period of extremely high temperature conditions, the asphalt sealing materials were separated and leaked into the structure. Therefore, the aim of the research is to provide the quality standard of asphalt sealing material based on the various temperature changes depending on seasons. According to the experimental results, the temperature of the sealing materials applied on the slab was increased up to $54^{\circ}C$ which was $3^{\circ}C$ higher than the structure temperature of $51^{\circ}C$. Based on the melting test for asphalt sealing materials applied on the outside wall of the structure, in the case of water-dispersing typed materials showed significant melting down due to its slow evaporation and low viscosity. Furthermore, from the accelerated test conducted indoor conditions, a solvent-type and water-dispersing typed materials showed significant melting down due to their low viscosity and melting point in ambient conditions. Based on these results, viscosity and melting point are found as the important factors on asphalt sealing materials' quality, and it is necessary to designate the quantitative level of the viscosity and melting point for quality control.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.1
• /
• pp.27-34
• /
• 2017

Recently, a demand in sustainable green technologies is requiring the lead free bonding for high power module packaging due to the environmental pollution. The Transient-liquid phase (TLP) bonding can be a good alternative to a high Pb-bearing soldering. Basically, TLP bonding is known as the combination of soldering and diffusion bonding. Since the low melting temperature material is fully consumed after TLP bonding, the remelting temperature of joint layer becomes higher than the operating temperature of the power module. Also, TLP bonding is cost-effective process than metal nanopaste bonding such as Ag. In this paper, various TLP bonding techniques for power semiconductor were described.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.332-333
• /
• 2013

This research utilizes the modified sulfur having the low melting point which 65℃ is tries to study the strength property of the mortar according to the cure method of the modified sulfur mortar. And we try to use as basic data for investigating the curing condition of the light panel optimum utilizing the modified sulfur. We experimented by five kinds; 20℃ water curing method and 20, 40, 60, 80(℃) air dry curing method. In 3 day curing, the compressive strength was improved caused by high curing temperature. But the compressive strength was degraded caused by enhanced temperature in 7day curing and 28day curing. Therefore, the curing temperature of the modified sulfur mortar is determined that it comes 20 time case curing and the water curing is the most recommendable.

• Journal of Korean Society of societal Security
• /
• v.3 no.1
• /
• pp.43-50
• /
• 2010

Sliding accidents on the road have a high percentage by road freezing, especially, they often have appeared at bridges and Tunnel of freezing areas. Thus, the stability of road operations is enhanced by preventing partial freezing phenomenon. According to the geothermal snow melting system analysis, a pattern of thermal conductivity is found out; pavement materials of concrete and asphalt where the system is buried. The heat transfer simulation is essential when the geothermal snow melting system is applied according to heating exchanger pipe placed in the lower pavements. The model tests are conducted on low temperature in freezer using the manufactured test model which is equal to pavement materials. Many variables are discovered from numerical analyses under the same conditions with model test.

• Resources Recycling
• /
• v.6 no.1
• /
• pp.29-34
• /
• 1997

The feasibility of using the industrial inorganic waste materials such as l~mestone sludge. Soundly sand. coal fly 'ash, and chemical glasses as a raw material for cement clinker by melting treatmeut was iovestigated. The slag wh~ch is obtained from thc melts of the mixtnres of waste materials is composed of P-C,S(ZCaO - SIOJ and C,AS(ZCaO . AI,O, . SiO,) phases. The effect of melting tempcrabre, coaling condition and CIS ratio on the fo~mation of P-C,S phasc was examed. In order to obtain thc P-CiS phase which is useful in thc utilhtion as a clinkcr malcrid, it B found that sudl considerations as low melting temperature as possible of the wastc mixhire, quenching the melts and law CIS ratio of the mlxhlre are necessary.

• Journal of Powder Materials
• /
• v.30 no.5
• /
• pp.431-435
• /
• 2023

An irradiation hardening of Inconel 718 produced by selective laser melting (SLM) was studied based on the microstructural observation and mechanical behavior. Ion irradiation for emulating neutron irradiation has been proposed owing to advantages such as low radiation emission and short experimental periods. To prevent softening caused by the dissolution of γ' and γ" precipitates due to irradiation, only solution annealing (SA) was performed. SLM SA Inconel 718 specimen was ion irradiated to demonstrate the difference in microstructure and mechanical properties between the irradiated and non-irradiated specimens. After exposing specimens to Fe³⁺ ions irradiation up to 100 dpa (displacement per atom) at an ambient temperature, the hardness of irradiated specimens was measured by nano-indentation as a function of depth. The depth distribution profile of Fe³⁺ and dpa were calculated by the Monte Carlo SRIM (Stopping and Range of Ions in Matter)-2013 code under the assumption of the displacement threshold energy of 40 eV. A transmission electron microscope was utilized to observe the formation of irradiation defects such as dislocation loops. This study reveals that the Frank partial dislocation loops induce irradiation hardening of SLM SA Inconel 718 specimens.

• Atmosphere
• /
• v.25 no.1
• /
• pp.31-49
• /
• 2015

From the hourly data of 75 Korean weather stations over a 12-year period (2001~2012), this study has chosen three cases (January 12, 2006; January 11, 2008; and February 22, 2009) of multiple freezing rains and investigated the atmospheric circulations that seemed to cause the events. As a result, the receding high pressure type (2006), prevailing high pressure type (2008), and warm front type (2009) are confirmed as synoptic patterns. In all three cases, freezing rain was found in regions with a strong ascending current near the end point of a low-level jet that carried the warm humid air from low latitudes. The strong ascending current resulted from lower-level convergence and upper-level divergence. In 2006 and 2009, the melting process was confirmed. In 2008, the supercooled warm rain process (SWRP) was confirmed. In contrast to existing SWRP theory, it was found that the cool air produced at the middle atmosphere and near the earth's surface led to the formation of freezing rain. The sources of this cool air were supposed to be the evaporative latent heat and the cold advection coming from the northeast. On the other hand, a special case was detected, in which the freezing rain occurred when both the soil surface temperature and surface air temperature were above $0^{\circ}C$. The thickness distributions related to freezing rain in Korea were found to be similar to those in North America. A P-type nomogram was considered for freezing rain forecasting; however, it was not relevant enough to Korea, and few modifications were needed.

• Korean Journal of Materials Research
• /
• v.26 no.12
• /
• pp.681-687
• /
• 2016

Zirconium(Zr) nuclear fuel cladding tubes are made using a three-time pilgering and annealing process. In order to remove the oxidized layer and impurities on the surface of the tube, a pickling process is required. Zr is dissolved in HF and $HNO_3$ mixed acid during the process and pickling waste acid, including dissolved Zr, is totally discarded after being neutralized. In this study, the waste acid was recycled by adding $BaF_2$, which reacted with the Zr ion involved in the waste acid; $Ba_2ZrF_8$ was subsequently precipitated due to its low solubility in water. It is very difficult to extract zirconium from the as-recovered $Ba_2ZrF_8$ because its melting temperature is $1031^{\circ}C$. Hence, we tried to recover Zr using an electrowinning process with a low temperature molten salt compound that was fabricated by adding $ZrF_4$ to $Ba_2ZrF_8$ to decrease the melting point. Change of the Zr redox potential was observed using cyclic voltammetry; the voltage change of the cell was observed by polarization and chronopotentiometry. The structure of the electrodeposited Zr was analyzed and the electrodeposition characteristics were also evaluated.

• Resources Recycling
• /
• v.23 no.5
• /
• pp.3-11
• /
• 2014

Calcium ferrite is more effective binder for making sintered ore and flux for steel making because of it's low melting temperature. In this Study, calcium ferrite was made by calcinating method in the cement manufacturing process in order to reduce manufacturing costs and increase productivity. Limestone and calcination sludge were used as CaO source, steelmaking sludge, blast furnace dust and iron ore were used as Fe-bearing raw materials. The sintering temperature of specimens is in the range of $950{\sim}1170^{\circ}C$. For Calcium ferrite can be used 'binder for making sintered ore' or 'flux for converter/electric furnace' with a low melting point properties, the raw material characteristics and sintering properties were investigated.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.76-76
• /
• 2009

눈부신 전자산업의 발달로 대부분의 전자제품이 다기능/경박단소화 되고 있어, 고밀도 실장 기술인 양면 표면실장과 고집적 패키징 기술인 패키지 적층 공정의 적용이 점차 확대되고 있다. 따라서 양면 표면실장 및 패키지 적층 공정에 사용되는 저온 접합용 무연 솔더 즉, $183^{\circ}C$(Sn-37Pb 공정 솔더 융점) 이하의 융점을 가지는 저온 무연 솔더에 대한 관심이 높아지고 있다. 한편, 미세피치 적용 분야에 있어 ACF/P를 이용한 COG 접속 분야 외에도 최근 저온 접합용 무연 솔더를 이용한 접속 분야가 각광을 받고 있다. 따라서, 접속피치 미세화에 대응하기 위해 스크린 인쇄성을 향상시킬 수 있는 저온 무연 솔더 paste 제조 및 공정 기술의 개발이 필요한 실정이다. 현재 대표적인 저온 무연 솔더 조성은 Sn-Bi계($138^{\circ}C$ 융점)와 Sn-In계($120^{\circ}C$ 융점)이다. 하지만, 이들 조성의 신뢰성 등에 있어 개선의 여지가 있으므로 이를 해결하기 위한 무연솔더 조성의 개발이 필요하다. 이와 같은 관점에서, 본 연구는 $137^{\circ}C$의 융점을 갖는 Sn-57.6Ag-0.4Ag 저온 무연 솔더 paste를 $217^{\circ}C$의 융점을 갖는 Sn-3.0Ag-0.5Cu 솔더 paste와 비교하여 인쇄성, reflow 특성, void inspection, 미세조직 관찰 및 underfill 적용 등의 실험을 실시하였다.