• Journal of the Optical Society of Korea
• /
• v.14 no.3
• /
• pp.277-281
• /
• 2010

We propose a design and optimization method for a dielectric-loaded surface plasmon polariton waveguide using a genetic algorithm. This structure consists of a polymer ridge on top of two layers of substrate and gold film. The thickness, width and refractive index of the ridge are designed to optimize the figures of merit including mode confinement and propagation length. The modal analysis combined with the effective index method shows that the designed waveguide exhibits a fundamental propagation mode with high mode confinement while ensuring that the propagation loss remains relatively low.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.3
• /
• pp.676-682
• /
• 2018

In order to study electrical properties of epoxy composites with various frequency. To measure of dielectric characteristics have been performed over a frequency range from 30[Hz] to 3[MHz] and a temperature range of $20[^{\circ}C]$, $100[^{\circ}C]$, $140[^{\circ}C]$. We observed values of dielectric constant and dissipation of the epoxy composites with various frequency. We were observed dielectric loss and dispersion in low frequency region. Also, we observed to decrease of the dielectric constant due to the effects of filler in high temperature region.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.10
• /
• pp.1780-1785
• /
• 2016

This paper presents few case studies of state diagnosis of XLPE cables using very low frequency techniques. The power cables of 22.9kV which have installation fault were assessed using VLF technique in addition to other techniques like insulation resistance and DC voltage withstand test. From the experimental results, The dielectric loss($tan{\delta}$) values of degradation of the cable(joint, knife, needle) at $U_0$ were 5.839, 5.526 and 6.251, respectively and all values were "further study advised". VLF PD measurement was also found defective portion. These method was effective in defect to fault in the degradation of the cable. However, the breakdown did not occur in the degradation of the cable because of properties of XLPE insulation. Few case studies of using VLF $tan{\delta}$ diagnosis for fault are measured and analyzed. The $tan{\delta}$ values at $U_0$ were "further study advised" or "action required".

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.766-770
• /
• 2007

In this study, in order to develop low temperature sintering ceramics for multilayer piezoelectric actuator, $0.07Pb(Mn_{1/3}Nb_{2/3})O_3-xPb(Ni_{1/3}Nb_{2/3})O_3-(0.93-x)Pb(Zr,Ti)O_3$ ceramics system were fabricated using $Li_2CO_3-Bi_2O_3-CuO$ sintering aids and the specimens were sintered at $930^{\circ}C$. Thereafter, their piezoelectric and dielectric characteristics were investigated according to the amount of PNN substitution. At 9 mol% PNN substitution, density, electromechanical coupling factor ($k_p$), dielectric constant, mechanical quality factor ($Q_m$) and piezoelectric constant ($d_{33}$) showed the optimum value of $7.86g/cm^3$, 0.60, 1640, 1323 and 387 pC/N, respectively. It is considered that these values are suitable for piezoelectric divece application such ad multilayer piezoelectric actuator and ultrasonic vibrator with pure Ag internal electrode.

• Journal of Magnetics
• /
• v.11 no.4
• /
• pp.164-166
• /
• 2006

We have investigated the dielectric and magnetic properties of ferroelectric-antiferromagnetic $BaTiO_{3}-LaMnO_{3}$ composite with changing relative mole percents. Due to high sintering temperature, i.e. $1150^{\circ}C$, the Ba ion in $BaTiO_{3}$ seems to diffuse into $LaMnO_{3}$; resulting in $BaTiO_{3}-(La,Ba)MnO_{3}$ ferroelectric-ferromagnetic composite. At room temperature, $0.9BaTiO_{3}-0.1LaMnO_{3}$ composite exhibits considerable magnetization (${\sim}0.7\;emu/g\;at\;2000\;Oe$) and low coercive field (${\sim}5\;Oe$). Also it exhibits high dielectric constant (${\sim}560$) and low loss (${\sim}0.08$) at 10 kHz. This result may imply that $BaTiO_{3}-LaMnO_{3}$ could be suitable for a low leakage multiferroic composite.

• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.123-130
• /
• 1997

In this study, (Sr.Pb.Ca)TiO3-Bi2O3.3TiO2(SPCT) systems were investigated to develop a new material which has a high dielectric constant, a low dielectric loss and a small TCC(Temperature Coefficient of Capa-citance), and are suitable for high voltage applications as a function of the additions of Bi2O3.3TiO2 from 5 mol.% to 9 mol.%. The result obtained from our investigation showed that up to 6 mol.% Bi2O3.3TiO ad-dition the dielectric constant increased and it deteriorated at higher concentrations with increasing amount of the acicular grains. As a result of some dopants (SiO2, Nb2O3, MnO2) addition to SPCT, the specimens with MnO2 showed good dielectric properties. The dielectric constant decreased, but the TCC was improved with the addition of MnO2 from 0.15 wt.% to 0.45 wt. %.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.35-40
• /
• 2010

The variations of dielectric properties of $Ta_2O_5-SiO_2$ continuous composition spread thin films prepared by off-axis radio-frequency magnetron sputtering were investigated. The dielectric maps of dielectric constant and loss were plotted via 1500 micron-step measuring. The specific points showing superior dielectric properties of high dielectric constant (k~19.5) and loss (tan${\delta}$<0.05) at 1 MHz were found in area of the distance of 16 mm and 22 mm apart from $SiO_2$ side in $75{\times}25mm^2$ sized Pt/Ti/$SiO_2$/Si(100) substrates.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.570-572
• /
• 2012

In this paper, a three-dimensional (3-D) low-loss and wide-band BPF based on low-temperature co-fired ceramic (LTCC) has been presented for mm-wave wireless communication applications. The proposed BPF is designed in a 6-layer LTCC substrate. The double patch resonators are fully integrated into the LTCC dielectrics and vertical via and planar CPW transitions are designed for interconnection between embedded resonators and in/output ports and MMICs, respectively. The designed BPF was fabricated in a 6-layer LTCC dielectric. The fabricated BPF shows a centre frequency (fc) of 53.23 GHz and a 3dB bandwidth of 14.01 % from 49.5 to 56.9 GHz (7.46 GHz). An insertion loss of -1.56 dB at fc and return losses below -10 dB are achieved. Its whole size is $4.7{\times}1.7{\times}0.684mm^3$.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1487-1489
• /
• 1994

$(Zr_{0.65}Sn_{0.35})Ti_{1.04}O_4$ system which has a dielectric constant, low dielectric loss and temperature coefficient was investigated. Temperature coefficient varied from positive to negative with increasing of NiO. For the NiO content 1.0wt%. i.e $(Zr_{0.65}Sn_{0.35})Ti_{1.04}O_4$, the ceramic showed very good dielectric properties such as ${\epsilon}$=37.8, $Q{\times}f_o=49.000$ and ${\tau}_r= 4{\pm}1ppm/^{\circ}C$.

• The Korean Journal of Ceramics
• /
• v.2 no.2
• /
• pp.111-113
• /
• 1996

Dielectric properties at microwave frequency region of the five-layered compound $Ba_5Nb_4O_{15}$ prepared by the conventional solid state reaction method were investigated. $Ba_5Nb_4O_{15}$ has excellent microwave dielectric characteristics; ${\varepsilon}_r$=38, Q=7500 at 10 GHz, and ${\tau}_l$=+50 ppm/K. Since this compound has a high dielectric constant, high Q and sufficiently stable characteristics, it is useful for the applications at microwave frequencies.