• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.10
• /
• pp.1009-1015
• /
• 2006

The elcetrodewatering filter press(EDFP) which had anode and cathod plates to be set between filter plates was built for reducing the waterworks sludge and improving performance of dewatering equipment. Several tests to compare the dewaterability with conventional mechanical filter press dewatering(MDEP) and EDFP was conducted through this equipment. As test results, filtration amount discharged from EDFP measured 43.2 kg which increased against MDFP, and cake weight measured 4 kg which was two times against MDFP. The water content of dewatered cake from EDFP was 55wt% and dewatering velocity was 2.3 $kg/m^2{\cdot}cycle$. This water content decrease 20% and dewatering velocity increased 30% with compare to the MDFP. That is to say, EDFP constructed from electrodewatering mechanism increase filtrate discharging amount, which make dewatering velocity increase and produce the low water content dewatered cake against MDFP. Energy consumption of EDFP is analysed to 400 kwh/DS ton. The results to analysis the economical aspect considering the power consumption and the handling cost decline as sludge volume reduction due to producing the low water content cake showed that expenses to handle sludge of 1 ton by dry solid base cut down on 20,000 won. If considering several test aspects, it was analysed that EDFP was excellent in the side of performance as well as economical suitability.

• Economic and Environmental Geology
• /
• v.51 no.5
• /
• pp.429-438
• /
• 2018

Since concrete is a hardened aggregates of various materials, it needs to be crushed for chemical analyses. However, the effect of sample crushing on the analytical results has not been precisely assessed till today. In this study, we prepared concrete test pieces using Portand cements and fly ashes as binding materials, and ponded ashes and sands as aggregates and analyzed the heavy metals of the test pieces using Standards for Fair Testing of Soil Contamination (SFTSC) and Wastes (SFTW). For this, each test piece was partially crushed at first and sieved for separation of grains of <0.15 mm, 0.15-0.5 mm, and 0.5-5 mm from the same crushed samples (Crushing Method I). Results of those samples using SFTSC showed a clear trend that analyzed heavy metal concentrations are higher in the finer fractions. Particularly, fractions with <0.15 mm indicated much higher concentrations than the theoretical ones, which were calculated based on the concentrations of individual materials and their mixing fractions. In contrast, the analytical results were generally comparable with the theoretical ones when the test pieces were totally pulverized such that all the crushed grains were <0.15 mm in size (Crushing Method II). These results are associated with the fact that cement materials and fly ashes, which are high in heavy metals relative to other materials, are enriched in the fine fractions. The analytical results using the SFTW derived very low concentrations in most of parameters and did not indicate the dependence of concentrations on the crushing methods due to using distilled water as leaching agent.

• Journal of Digital Convergence
• /
• v.15 no.6
• /
• pp.315-327
• /
• 2017

This study was carried out to examine the converging factors related to academic burnout in students from health-related majors who are involved in studying for the Test of English for International Communication (TOEIC). Research subjects included 291 randomly selected students from the J-region, who were enrolled in TOEIC classes. Data collection took place from April 3, 2017 to April 14, 2017, using anonymous self-administered questionnaires. The results of a multiple regression analysis in female students showed higher academic burnout pertaining to studying for the TOEIC when sleeping hours, self-worth, self-efficacy, school adaptation resilience, and study immersion were low, and job-seeking stress and test anxiety were high. The explanatory power of this model was 65%. Based on these results, to reduce academic burnout pertaining to studying for the TOEIC in health majors, it is first necessary to increase sleeping hours, self-worth, self-efficacy, school adaptation resilience, and study immersion, and to make efforts to manage self-competence, job-seeking stress, and test anxiety. The results of this study may be used to decrease the academic burnout caused by studying for the TOEIC in health major students and to increase their aptitude for studying English, to cultivate globalized capabilities. Future studies need to conduct an effect analysis on the control and mediation effect that these factors have on academic burnout.

• Safety and Health at Work
• /
• v.11 no.1
• /
• pp.118-124
• /
• 2020

Background: The poultry industry in Pakistan has flourished since the 1960s; however, there are scarce data regarding the impact of occupational exposure on the pulmonary health of farm workers in terms of years working in the industry. The objective of the present study was to assess the effect of poultry environment on the health of occupationally exposed poultry farmers in countries of warm climatic regions, such as Pakistan. This study will also show the effect of exposure to poultry facilities on the health of poultry farmers in the context of low-income countries with a relatively inadequate occupational exposure risk management. Materials and methods: The lung function capacity of 79 poultry workers was measured using a spirometer. Along with spirometry, a structured questionnaire was also administrated to obtain information about age, height, weight, smokers/nonsmokers, years of working experience, and pulmonary health of farm workers. The workers who were directly involved in the care and handling of birds in these intensive facilities were considered and divided into four groups based on their years of working experience: Group I (3-10 months), Group II (1-5 years), Group III (6-10 years), and Group IV (more than 11 years). The forced vital capacity (FVC), forced expiratory volume in one second (FEV1) and the FEV1/FVC ratio were considered to identify lung function abnormalities. Statistical analysis was carried out using independent sample t test, Chi-square test, Pearson's correlation, and linear regression. Results: Based on the performed spirometry, 68 (86 %) of workers were found normal and healthy, whereas 11 (14 %) had a mild obstruction. Of the 11 workers with mild obstruction, the highest number with respect to the total was in Group IV (more than 11 years of working experience) followed by Group III and Group II. Most of the workers were found healthy, which seems to be because of the healthy survivor effect. For the independent sample t test, a significant difference was noticed between healthy and nonhealthy farmers, whereas Chi-square test showed a significant association with height, drugs, and working experience. Linear regression that was stratified by respiratory symptoms showed for workers with symptoms, regression models for all spirometric parameters (FVC, FEV1, and FEV1/FVC) have better predictive power or R square value than those of workers without symptoms. Conclusion: These findings suggest that lung function capacity was directly related to years of working experience. With increasing number of working years, symptoms of various respiratory problems enhanced in the poultry workers. It should be noted that most of the poultry workers were healthy and young, the rationale being that there is a high turnover rate in this profession. The mobility in this job and our finding of 86% of the healthy workers in the present study also proposed healthy worker survivor effect.

• Korean Journal of Biological Psychiatry
• /
• v.21 no.4
• /
• pp.168-174
• /
• 2014

Objectives Sensory gating dysfunctions in patients with schizophrenia and bipolar disorder have been investigated through two similar methods ; P50 suppression and prepulse inhibition paradigms. However, recent studies have demonstrated that the two measures are not correlated but rather constitute as distinct neural processes. Recent studies adopting spectral frequency analysis suggest that P50 suppression reflects the interaction between gamma and other frequency bands. The aim of the present study is to investigate which frequency component shows more significant interaction with gamma band. Methods A total of 108 mood disorder patients and 36 normal subjects were included in the study. The P50 responses to conditioning and test stimuli with an intra-pair interval of 500 msec were measured in the study population. According to P50 ratio (amplitude to the test stimulus/amplitude to the conditioning stimulus), the subjects with P50 ratio less than 0.2 were defined as suppressed group (SG) ; non-suppressed group (NSG) consisted of P50 ratio more than 0.8. Thirty-five and 25 subjects were included in SG and NSG, respectively. Point-to-point correlation coefficients (PPCCs) of both groups were calculated between two time-windows : the first window (S1) was defined as the time-window of one hundred millisecond after the conditioning auditory stimulus and the second window (S2) was defined as the time-window of 100 msec after the test auditory stimulus. Spectral frequency analysis was performed to investigate which frequency band results in the difference of PPCC between SG and NSG. Results Significant reduction of PPCC between S1 and S2 was observed in the SG (Pearson's r = 0.24), compared to PPCC of the NSG (r = 0.58, p < 0.05). In spectral frequency analysis, gamma band showed "phase-reset" and similar responses after the two auditory stimuli in suppressed and non-suppressed group. However in the case of alpha band, comparison showed significantly low PPCC in SG (r = -0.14) compared to NSG (r = 0.36, p < 0.05). This may be reflecting "phase-out" of alpha band against gamma band at approximately 50 msecs after the test stimulus in the SG. Conclusions Our study suggests that normal P50 suppression is caused by phase-out of alpha band against gamma band after the second auditory stimulus. Thus it is demonstrated that normal sensory gating process is constituted with attenuated alpha power, superimposed on consistent gamma response. Implications of preserved gamma and decreased alpha band in sensory gating function are discussed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.1
• /
• pp.183-194
• /
• 2004

It's essential process to study non-linear material function related to characteristics of compressibility and permeability when we predict the consolidation behavior of soft clay ground. In this study, laboratory tests were conducted to find out the material function using marine clay. Standard oedometer test and Rowe cell test were performed with conditions, which were classified into vertical drainage only, radial drainage only and vertical-radial drainage case. Modified oedometer test equipment was developed to find out the material function and special extrusion device was originated to minimize the sample disturbance effect. Reliability of the results in modified oedometer test could be confirmed by comparing with the Rowe cell's one. Effective stress - void ratio - permeability relations were analyzed using all testing results. As a result, void ratio with effective stress level could be expressed by the power function and permeability with void ratio could be expressed by exponential function. In soft clay with high initial water content and low shear strength, non-linear characteristics related to compressibility and permeability varied with wide range by the effective stress levels. It's important to note that non-linearity of the material function should be considered at prediction of the consolidation behavior.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.89-94
• /
• 2021

The mechanical reliability of flexible devices has become a major concern on their commercialization, where the importance of reliable bonding is highlighted. In terms of component materials' properties, it is important to consider thermal damage of polymer substrates that occupy large area of the flexible device. Therefore, room temperature bonding process is highly advantageous for implementing flexible device assemblies with mechanical reliability. Conventional epoxy resins for the bonding still require curing at high temperatures. Even after the curing procedure, the bonding joint loses flexibility and exhibits poor fatigue durability. To solve this problems, low-temperature and adhesive-free bonding are required. In this work, we develop a room temperature bonding process for polymer substrates using carbon nanotube heated by microwave irradiations. After depositing multiple-wall carbon nanotubes (MWNTs) on PET polymer substrates, they are heated locally with by microwave while the entire bonding specimen maintains room temperature and the heating induces mechanical entanglement of CNT-PET. The room temperature bonding was conducted for a PET/CNT/PET specimen at 600 watt of microwave power for 10 seconds. Thickness of the CNT bonding joint was very thin that it obtains flexibility as well. In order to evaluate the mechanical reliability of the joint specimen, we performed lap shear test, three-point bending test, and dynamic bending test, and confirmed excellent joint strength, flexibility, and bending durability from each test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.5
• /
• pp.443-452
• /
• 2021

College students face serious difficulties while seeking jobs, leading to a high degree of stress, which is thought to affect their attitude towards smoking. The purpose of this study was to identify the relationship between hardiness, job-seeking stress, and the attitude towards smoking among students, and to further identify the factors influencing smoking attitude. Data were collected using a structured questionnaire administered to 145 students. Data analysis was performed using the SPSS program, t-test, ANOVA, Kruskal Wallis test, Pearson's Correlation Coefficients, and hierarchical multiple regression analysis. Smokers constituted 22.1% of the sample. The study showed that smoking attitudes varied according to the smoking status (H=28.26, p<.001). The smoking attitude was seen to be desirable in the high group (t=-3.27, p=.001) and low job-seeking stress group (t=4.40, p<.001). There was a positive correlation between hardiness and smoking attitude (r=.18, p=.028). There was a negative correlation between job-seeking stress and smoking attitude (r=-.28, p=.001). Also, the factors affecting the smoking attitude were non-smoker respondent (β=.50, p<.001), job-seeking stress (β=-.23, p=.015), former smoker respondent (β=.22, p=.016) and the explanatory power was 24.3%. Therefore, school and health public center counseling and employment support programs need to help students manage and cope with stressful situations to change their attitude towards smoking in a desirable direction.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5877-5884
• /
• 2014

Recently, abnormally cold weather has been reported more frequently in winter due to the climate change and abnormal weather changes. On the other hand, the heating capacity of a railcar may be not enough to warm the cabin under severe cold climatic conditions, which is one of the reasons for the passengers' complaints about heating. In this study, the effects of ambient temperature and heater power on the cabin temperature was investigated to obtain the minimum ambient temperature for the tested railcar. The test railcar was placed in a large-climatic chamber, and various ambient temperature conditions were simulated. The effects of the heater output were investigated by monitoring the cabin temperature under a range of heater output conditions. The mean cabin temperature was $14.0^{\circ}C$, which was far lower than the required minimum temperature of $18^{\circ}C$, under a $-10^{\circ}C$ ambient temperature condition with the maximum heat power. When the ambient temperature was set to $0^{\circ}C$ and $10^{\circ}C$, the maximum achievable cabin temperature was $26.1^{\circ}C$ and $34.0^{\circ}C$. Through calculations using the interpolation method, the minimum ambient temperature to maintain an $18^{\circ}C$ cabin temperature was $-6.7^{\circ}C$ for this car. The vertical temperature difference was higher with a higher power output and higher ambient temperature. The maximum vertical temperature difference was higher than $10^{\circ}C$ in some cases. However, the horizontal temperature difference vs. low temperature (< $2^{\circ}C$) was independent of the power output and ambient temperature. As a result, it is very important to reduce the vertical temperature difference to achieve good heating performance.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.5
• /
• pp.62-70
• /
• 2007

In this paper, the boost Power Factor Correction(PFC) technique for Direct Torque Control(DTC) of brushless DC motor drive in the constant torque region is implemented on a TMS320F2812DSP. Unlike conventional six-step PWM current control, by properly selecting the inverter voltage space vectors of the two-phase conduction mode from a simple look-up table at a predefined sampling time, the desired quasi-square wave current is obtained, therefore a much faster torque response is achieved compared to conventional current control. Furthermore, to eliminate the low-frequency torque oscillations caused by the non-ideal trapezoidal shape of the actual back-EMF waveform of the BLDC motor, a pre-stored back-EMF versus position look-up table is designed. The duty cycle of the boost converter is determined by a control algorithm based on the input voltage, output voltage which is the dc-link of the BLDC motor drive, and inductor current using average current control method with input voltage feed-forward compensation during each sampling period of the drive system. With the emergence of high-speed digital signal processors(DSPs), both PFC and simple DTC algorithms can be executed during a single sampling period of the BLDC motor drive. In the proposed method, since no PWM algorithm is required for DTC or BLDC motor drive, only one PWM output for the boost converter with 80 kHz switching frequency is used in a TMS320F2812 DSP. The validity and effectiveness of the proposed DTC of BLDC motor drive scheme with PFC are verified through the experimental results. The test results verify that the proposed PFC for DTC of BLDC motor drive improves power factor considerably from 0.77 to as close as 0.9997 with and without load conditions.