• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.3A
• /
• pp.282-290
• /
• 2006

In this paper, we propose an enhanced Timing Estimator algorithm for 2.45GHz LR-WPAN receiver. Because an expensive and highly efficient oscillator can't be used for low-cost implementation, a Timing Estimator algorithm having stable operation in the channel environment with center frequency tolerance of 80 ppm is required. To enhance the robustness to frequency offset and the stability of receiver performance, multiple delay differential filter is adopted. By utilizing the characteristic that the correlation result between the output signal of Multiple delay differential filter and reference signal is restricted on the In-phase part of the correlator output, a coherent detection scheme instead of the typical noncoherent one is adopted for Timing Estimator. The application of the coherent detection scheme is suitable for LR-WPAN receiver aimed at low-cost, low-power, and low-complexity, since it can remove performance degradation due to squaring loss of I/Q squaring operation and decrease implementation complexity. Computer simulation results show that the proposed algorithm achieved performance improvement compared with the differential detection-based noncoherent scheme by 2dB in average.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.585-593
• /
• 2017

In this paper, we propose a deblocking filter hardware architecture for low-power HEVC (High-Efficiency Video Coding) in-loop for mobile systems. HEVC performs image compression on a block-by-block basis, resulting in blockage of the image due to quantization error. The deblocking filter is used to remove the blocking phenomenon in the image. Currently, UHD video service is supported in various mobile systems, but power consumption is high. The proposed low-power deblocking filter hardware structure minimizes the power consumption by blocking the clock to the internal module when the filter is not applied. It also has four parallel filter structures for high throughput at low operating frequencies and each filter is implemented in a four-stage pipeline. The proposed deblocking filter hardware structure is designed with Verilog HDL and synthesized using TSMC 65nm CMOS standard cell library, resulting in about 52.13K gates. In addition, real-time processing of 8K@84fps video is possible at 110MHz operating frequency, and operation power is 6.7mW.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.12
• /
• pp.1227-1236
• /
• 2012

The low speed machinery faults are usually caused by the bearing failure of the rolling elements. As the life time of the bearing is limited, the condition monitoring of bearing is very important to maintain the continuous operation without failures. A few monitoring techniques using time domain, frequency domain and fuzzy neural network vibration analysis are introduced to detect and diagnose the faults of the low speed machinery. This paper presents a method of fault detection for the rolling element bearing in the low speed machinery using the Wiener filtering and shock pulse counting techniques. Wiener filter is used for noise cancellation and it clearly makes the shock pulse emerge from the time signal with the high level of noise. The shock pulse counting is used to determine the various faults obviously from the shock signal with transient pulses not related with the bearing fault. Machine fault simulator is used for the experimental measurement in order to verify this technique is the powerful tool for the low speed machine compared with the frequency analysis. The test results show that the method proposed is very effective parameter even for the signal with high contaminated noise, speed variation and very low energy. The presented method shows the optimal tool for the condition monitoring purpose to detect the various bearing fault with high accuracy.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.109-112
• /
• 2007

Definition-Enhancement of the digitalized image has been being made researches continuously due to application a camera to a mobile-apparatus and the advent of a digital camera. In particular, the inputted image from a sensor goes through the process of ISP(Image Signal Process) prior to output as a visual image. The high-frequency components are offset by LPF(Low Pass Filter) that eliminates the noise of high spatial-frequency at the moment. In this paper, we propose an algorithm that outputs more vivid image by using adaptive-HPF(High Pass Filter) that has apt coefficients for diverse conditions of an image edge, nevertheless we do not employ any Edge-Detection algorithm to enhance a blurred image.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.37-44
• /
• 2007

A low-voltage high-linear bipolar OTA and its application to IF bandpass filter for GSM cellular telephone are presented. The OTA consists of a low-voltage linear transconductor, a translinear current gain cell, and three current mirrors. The bandpass filter is composed of two cascaded identical second-order bandpass filters, which consist of a resistor, a capacitor, and a grounded simulated inductor realized with two OTA's and a grounded capacitor. SPICE simulations using an 8 GHz bipolar transistor-array parameter show that the OTA with a transconductance of 1 mS exhibits a linearity error of less than ${\pm}2%$ over an input voltage range of ${\pm}0.65\;V$ at supply voltages of ${\pm}2.0\;V$. Temperature coefficient of the transconductance is less than $-90ppm/^{\circ}C$. The bandpass filter has a center frequency of 85 MHz and Q-factor of 80. Temperature coefficient of the center frequency is less than $-182ppm/^{\circ}C$. The power dissipation of the filter is 128 mW.

• Journal of Power Electronics
• /
• v.8 no.1
• /
• pp.91-100
• /
• 2008

The d-q harmonic detecting algorithms are dominant methods to generate current references for active power filters (APF). They are often implemented in the synchronous frame and time domain. This paper researches the frequency characteristics of d-q synchronous transformations, which are closely related to the analysis and design issues of control system. Intuitively, the synchronous transformation is explained with amplitude modulation (AM) in this paper. Then, the synchronous filter is proven to be a time-invariant and linear system, and its transfer function matrix is derived in the stationary frames. These frequency-domain models imply that the synchronous transformation has an equivalent effect of frequency transformation. It is because of this feature, the d-q method achieves band-pass characteristics with the low pass filters in the synchronous frame at run time. To simplify these analytical models, an instantaneous positive-negative sequence frame is proposed as expansion of traditional symmetrical components theory. Furthermore, the synchronous filter is compared with the traditional bind-pass filters based on these frequency-domain analytical models. The d-q harmonic detection methods are also improved to eliminate the inherent coupling effect of synchronous transformation. Typical examples are given to verify previous analysis and comparison. Simulation and experimental results are also provided for verification.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.3
• /
• pp.25-31
• /
• 2003

In this paper, we proposed a novel compact microstrip lowpass filter with an ultra-wide stopband and a sharp cutoff frequency response. To improve the cutoff response of the conventional filter, the coupling effect between two open stubs is used. The slot on the ground with conventional shunt open stubs plays an important role of increasing the stopband at a high frequency. The combination of these structures gives the filter the characteristics of an ultra-wide stopband with a prominent cutoff sharpness. The fabricated microstrip lowpass filter with the size of 19.2 mm $\times$ 14.9 mm has -3 dB cutoff frequency at 1.1 GHz and -20 dB stopband from 1.5 GHz to over 30 GHz. The insertion loss is less than -0.15 dB in the passband.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.4
• /
• pp.43-48
• /
• 2015

In this study, a method to enhance the dynamic range of seismic sensor is proposed. The low frequency noise included in the measurement of seismic sensor is modelled as an ARMA(Auto Regressive Moving Average) model and the order and parameters of the model are identified through system identification method. The identified noise model is augmented into Kalmman filter which estimate seismic signal from sensor measurement. The proposed method is applied to a newly developed seismic sensor which is MEMS based 3-axis accelerometer type. The experiment show that the proposed method can enhance the dynamic range compared to the simple low pass filtering.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.10C
• /
• pp.992-1000
• /
• 2009

Available electric wave resources have been limited than frequency demands that increase with the development of radio communication. According to FCC's (Federal Communication Commission) report, 70% of allocated spectrum was unused. This means that the lack phenomenon of electronic wave resources is ineffectively managed compare with the finiteness of frequency resources. According to the recognition of unused frequency within allocated band, this progress has been investigating to identify the unused TV channel and provide radio communication services. This paper proposed the sensing algorithm that efficiently recognizes the frequency resources which does not use and shares with the licensed user through using the multi-band CIC (Cascaded Integrator Comb) filter based on polyphase filter bank. The simulation results verifies that the proposed scheme can obtain the similar performance of variance and relatively low complexity to the existing scheme.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.257-260
• /
• 2000

In this paper, a Gm-C filter for low voltage and low power applications using a fully-differential transconductor is presented. The designed transconductor using the series composite transistors and the low voltage composite transistors has wide input range at low supply voltage. A negative resistor load (NRL) technology for high DC gain of the transconductor is employed with a common mode feedback (CMFB). As a design example, the third-order Elliptic lowpass filter is designed. The designed filter is simulated and examined by HSPICE using 0.25${\mu}{\textrm}{m}$ CMOS n-well parameters. The simulation results show 105MHz cutoff frequency and 2.4㎽ power dissipation with a 2.5V supply voltage.