• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.20 no.1
• /
• pp.113-124
• /
• 1990

For the study of the influence of kilovoltage and exposure time on radiographic density and contrast, we measured radiographic density of aluminum step wedge which composed of contiguous 8 steps wedges of 2-16㎜ thickness with densitometer. Aluminum step wedge was radiographed on Kodak ultraspeed DF-58 and Ektaspeed EP-21 film with range of 60-90 kVp and 5-60 impulse and subject contrast of aluminum step wedge with constant radiographic density and image contrast percentage without radiographic density was evaluated. Then we evaluated the film quality of teeth and their surrounding structure according to the change of kVp and exposure time by score rating method. The obtained results were as follows: 1. Radiographic density was related to the change of kilovoltage, especially in increased exposure time. 2. With constant radiographic density, subject contrast of thin aluminum step wedges was greater in low kilovolt age than high kilovoltage, but kilovolt age had not great influence on subject contrast of thick aluminum step wedge. On the other hand, radiographic density difference between 2mm and 16mm aluminum step wedge was decreased according to in- creasing kilovoltage. 3. Without constant radiographic density, image contrast percentage was decreased with increasing kilovoltage, but was not related with the change of exposure time. 4. Radiographic contrast of teeth and their surrounding structure which was taken with the range of 60-90 kVp and 6-30 impulse had not great influence on film quality.

• Journal of the Korean Ceramic Society
• /
• v.27 no.5
• /
• pp.661-667
• /
• 1990

Spinel powders were synthesized at the comparatively low-temperature range(800~90$0^{\circ}C$) by the emulsion-hot kerosene drying method and the effects of kerosene-evaporative conditions on powder characteristics were investigated. In emulsion drying, more unagglomerated and sinterable powders could be synthesized through rapid evaporation of emulsion at the higher kerosene temperature. The completion of formation reaction of spinel observed at the low-temperature range confirmed the high reactivity of powders. The relative theoretical density and the fracture toughness of spinel pellets sintered at 1$650^{\circ}C$ for 4hrs. were 98% and 2.1MN/m3/2, respectively.

• Journal of the Korean Ceramic Society
• /
• v.50 no.3
• /
• pp.226-230
• /
• 2013

We performed high pressure high temperature (HPHT) sintering for the 20 nm MgO powders at the temperatures from $600^{\circ}C$ to $1200^{\circ}C$ for only 5 min under 7 GPa pressure condition. To investigate the microstructure evolution and physical property change of the HPHT sintered MgO samples, we employed a scanning electron microscopy (SEM), density and Vickers hardness measurements. The SEM results showed that the grain size of the sintered MgO increased from 200 nm to $1.9{\mu}m$ as the sintering temperature increased. The density results showed that the sintered MgO achieved a more than 95% of the theoretical density in overall sintering temperature range. Based on Vickers hardness test, we confirmed that hardness increased as temperature increased. Our results implied that we might obtain the dense sintered MgO samples with an extremely short time and low temperature HPHT process compared to conventional electrical furnace sintering process.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.6
• /
• pp.67-76
• /
• 2007

Raining method has been widely used for preparing sand specimen because of its ability to reconstitute the homogeneous specimen with desired relative density and its reliability established by the numerous experiments on diverse influential factors. In conventional raining methods, adjustment of relative density is achieved by controlling the shutter porosity and the whole system is required to be re-adjusted to achieve the target relative density when the granular characteristics are changed. It is also observed from conventional methods that certain degrees of spatial variation in density exist and the limited range of relative density is reproduced. In this paper, raining system with porous plate is proposed. It is shown that the wide range of relative density can be achieved by controlling failing height only. This enhanced system is able to obviate the subtle control of shutter porosity and minimize the effect of falling distance, which in turn ensures the homogeneity of the specimen, especially for low relative density.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.38-39
• /
• 2017

This paper proposes a new control method for an AC-DC Buck converter which is utilized as a front-end converter of a 2-stage high power density adapter. In the conventional adapter applications, 2-stage configuration shows higher power transfer efficiency and higher power density than those of the single stage flyback converter. In the 2-stage AC-DC converter, the boost converter is widely used as a front-end converter. However, an efficiency variation between high AC line and low AC line is large. On the other hand, the proposed conduction band control method for a buck front-end converter has an advantage of small efficiency variation. In the proposed control method, switching operation is determined by a band control voltage which represents output load condition, and an AC line voltage. If the output load increasesin low AC line, the switching operation range is expanded in half of line cycle. On the contrary, in light load and high line condition, the switching operation is narrowed. Thus, the proposed control method reduces switching loss under high AC line and light load condition. A 60W prototype which is configured the buck and LLC converter with the proposed control method is experimented on to verify the validity of the proposed system. The prototype shows 92.16% of AC-DC overall efficiency and 20.19 W/in 3 of power density.

• Smart Structures and Systems
• /
• v.19 no.5
• /
• pp.499-512
• /
• 2017

Traditional structural dynamic analysis and Structural Health Monitoring (SHM) of large scale concrete civil structures rely on manufactured embedding transducers to obtain structural dynamic properties. However, the embedding of manufactured transducers is very expensive and low efficiency for signal acquisition. In dynamic structural analysis and SHM areas, piezoelectric transducers are more and more popular due to the advantages like quick response, low cost and adaptability to different sizes. In this paper, the applicable feasibility assessment of the designed "artificial" piezoelectric transducers called Concrete Piezoelectric Smart Module (CPSM) in dynamic structural analysis is performed via three major experiments. Experimental Modal Analysis (EMA) based on Ibrahim Time Domain (ITD) Method is applied to experimentally extract modal parameters. Numerical modal analysis by finite element method (FEM) modeling is also performed for comparison. First ten order modal parameters are identified by EMA using CPSMs, PCBs and FEM modeling. Comparisons are made between CPSMs and PCBs, between FEM and CPSMs extracted modal parameters. Results show that Power Spectral Density by CPSMs and PCBs are similar, CPSMs acquired signal amplitudes can be used to predict concrete compressive strength. Modal parameter (natural frequencies) identified from CPSMs acquired signal and PCBs acquired signal are different in a very small range (~3%), and extracted natural frequencies from CPSMs acquired signal and FEM results are in an allowable small range (~5%) as well. Therefore, CPSMs are applicable for signal acquisition of dynamic responses and can be used in dynamic modal analysis, structural health monitoring and related areas.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.12
• /
• pp.3579-3582
• /
• 2010

We studied the reaction of tri-methylaluminum (TMA) on hydroxyl (OH)-terminated Si (001) surfaces for the initial growth of aluminum oxide thin-films using density functional theory. TMA was adsorbed on the oxygen atom of OH due to the oxygen atom’s lone pair electrons. The adsorbed TMA reacted with the hydrogen atom of OH to produce a di-methylaluminum group (DMA) and methane with an energy barrier of 0.50 eV. Low energy barriers in the range of 0 - 0.11 eV were required for DMA migration to the inter-dimer, intra-dimer, and inter-row sites on the surface. A unimethylaluminum group (UMA) was generated at each site with low energy barriers in the range of 0.21 - 0.25 eV. Among the three sites, the inter-dimer site was the most probable for UMA formation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.218.1-218.1
• /
• 2014

In order to measure the absolute plasma density, various probes are proposed and investigated and microwave probes are widely used for its advantages (Insensitivity to thin non-conducting material deposited by processing plasmas, High reliability, Simple process for determination of plasma density, no complicate assumptions and so forth). There are representative microwave probes such as the cutoff probe, the hairpin probe, the impedance probe, the absorption probe and the plasma transmission probe. These probes utilize the microwave interactions with the plasma-sheath and inserted structure (probe), but frequency range used by each probe and specific mechanisms for determining the plasma density for each probe are different. In the recent studies, behaviors of each microwave probe with respect to the plasma parameters of the plasma density, the pressure (the collision frequency), and the sheath width is abundant and reasonably investigated, whereas relative diagnostic characteristics of the probes by a comparative study is insufficient in spite of importance for comprehensive applications of the probes. However, experimental comparative study suffers from spatially different plasma characteristics in the same discharge chamber, a low-reproducibility of ignited plasma for an uncertainty in external discharge parameters (the power, the pressure, the flow rate and so forth), impossibility of independently control of the density, the pressure, and the sheath width as well as expensive and complicate experimental setup. In this paper, various microwave probes are simulated by finite-different time-domain simulation and the error between the input plasma density in FDTD simulations and the measured that by the unique microwave spectrums of each probe is obtained under possible conditions of plasma density, pressure, and sheath width for general low-temperature plasmas. This result shows that the each probe has an optimum applicable plasma condition and reliability of plasma density measurement using the microwave probes can be improved by the complementary use of each probe.

• Progress in Superconductivity
• /
• v.2 no.1
• /
• pp.11-14
• /
• 2000

The notion of the finite pairing interaction energy range Td is shown to result in a linear temperature dependence of the London magnetic penetration depth length, ${\Delta}{\lambda}{/\lambda}(0)=(T/Td)2/\pi)ln2$ at low T in the case of the s-wave pairing state, accounting for data of high Tc superconductor by Hardy et al.

• KIEAE Journal
• /
• v.9 no.2
• /
• pp.17-26
• /
• 2009

High-rise and high-density apartment complexes have been built and supplied on a large scale in the 1st period New Town of metropolitan areas since the late 1980s. Recently it has become necessary to improve those apartment complexes which have blight problems for aging more than about 20 years accompanying simultaneity and a large scale. The purpose of this study is to analyze actual conditions of high-rise and high-density apartments in a view of sustainable regeneration. The contents and methods of this study are as follows. First, the concept of high-rise and high-density in domestic apartment developments were identified through review of literature and the law. Second, development conditions of Bundang new town and 1st period new town were studied. Third, the evelopment conditions of high-rise and high-density apartments in cases of 6 apartment complexes were analyzed from points of view of sustainable development by literature review and a field study. The results of this study are as follows. First, high-density range in domestic apartments can be conceptualized as 600 persons/ha. High-rise range in domestic apartments can be onceptualized as more than 11 stories under 30 stories. Second, characteristics and subjects based on actual conditions analysis could suggest on physio-environmental aspect and socio-economic aspect. Major characteristics and subjects of the physio-environmental aspect were 1.satisfaction of convenient facilities and public transportation service, 2.shortage of parking space, 3.uniform & blight of community facilities, 4.uniformed building layout, and 5.uniform pattern of unit plan and low flexibility by the bearing wall structure. And those of the socio-economical aspect were 1.satisfaction of current community, 2.increase and diversity of needs of the elderly by socio-demography change, 3.improvement of size and method of apartment complex development and 4.raising of economic-sufficiency.