• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 2005년도 학술대회
• /
• pp.109-112
• /
• 2005

ATSC 지상파 DTV 시스템에서 심볼 타이밍 동기 성능 개선을 위한 알고리즘을 제안한다. 일반적으로 심볼 타이밍 동기를 위해 사용되는 가드너 방법은 다중 경로 페이딩 환경에서 성능이 좋지만 지터에 의해 성능 열화가 발생한다. 지터량는 루프 필터 대역폭이 작을수록 작아지지만, 수렴속도는 느려지게 된다. 수렴속도는 빠르면서 수렴 후 지터량를 감소시키기 위해 일정시간마다 루프필터의 출력 값을 평균하고 이 평균값을 이용하여 옵셋량을 추정한 후 추정된 옵셋의 변화율에 따라 루프 필터의 대역폭을 줄여 지터의 크기를 줄이는 알고리즘을 제안한다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제52권9호
• /
• pp.520-525
• /
• 2003

A robust controller for large space structures(LSS) is studied from passivity point of view. While velocity sensors are commonly used for proportional-derivative (PD) control law to stabilize large space structures, if the structure can be controlled without velocity measurements, it is desirable against the failure of velocity sensors and for the cost reduction of the sensing system. In a recent result a dynamic output feedback control law has been provided using only displacement measurements. This paper presents a passivity-based controller design method and provides an alternative stability analysis tool for the previous displacement feedback robust control law. The closed-loop system can be viewed as a feedback interconnection of a passivated large space structure (LSS) and a strictly positive real (SPR) system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 D
• /
• pp.2637-2639
• /
• 2002

This paper presents the design and implementation of a baseband Modem using DSP that supports a wireless LAN. It is implemented with DSP and D/A and A/D Converters in baseband and tested without using IF and RF modules. In this paper, we have used the matched filler and DLL(delay lock loop) for synchronization. And the matched filter and the carrier recovery are directly connected. Therefore, the proposed architecture is very simple and the operation of DSP becomes fast.

• ETRI Journal
• /
• 제32권1호
• /
• pp.53-61
• /
• 2010

We propose a simple technique to stabilize the optical output intensity of a fiber ring resonator. The electronic feedback circuit system, which consists of two voltage control oscillators, a phase comparator, and a low pass filter, is applied to the fiber ring resonator in order to compensate the optical phase shift in the ring loop. The reference electrical signal determines the operating condition of the fiber ring resonator for the desired optical output signal. The experimental results within the operating range agree well with the analytical results. The simulated performance of the proposed model is also compared with that of other existing models and shows significant improvement over them.

• Journal of electromagnetic engineering and science
• /
• 제10권4호
• /
• pp.237-243
• /
• 2010

A wireless power transfer system based on magnetically coupled two resonators is analysed using the filter theory. Design equations for each lumped parameter circuit components are derived. As a result, change of coupling coefficient between the resonators and/or change of load resistance are easily responded. Effect of circuit loss to the design theory is also addressed. After designing a power transfer system, a real system is constructed using spiral and loop coils. Dependence of circuit elements on their dimensions is measured in advance and used to cope with the designed element values. Simulated response by use of designed element values and measured result are compared, indicating the validity of the theory.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.197-198
• /
• 2007

In this paper, a 10Gbps Clock and Data Recovery circuit is designed in $0.18{\mu}m$ CMOS Technology. The circuit incorporates a multiphase LC oscillator, a quarter-rate Bang-Bang phase detector, a Charge Pump and a second order loop filter. The simulation results show that the designed circuit has a peak-to-peak clock jitter of 4.1ps and a peak-to-peak recovered data jitter of 8ps while consuming about 44mW from a 1.8V supply.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1233-1235
• /
• 2000

A new control method of three phase converter without measuring input phase-voltage and DC-link voltage is proposed. Input phase-voltage of these required voltages is estimated using EKF(Extended Kalman Filter) and DC-link voltage is estimated from the measured line currents and the estimated input phase-voltage. This control method is achieved without PLL(Phase Locked Loop) which senses the angle of input phase-voltage and DC-link voltage sensor. In addition, the proposed method controls high power factor and DC-link voltage utilizing the estimated phase angle. This paper describes the effectiveness of the proposed estimated algorithm through simulations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.200-202
• /
• 2005

In this paper, improved rotor position estimation for position sensorless control system of the SRM (Switched Reluctance Motor) is presented. For more accurate rotor position estimation, the PLL (Phase Locked Loop) based position interpolation is adapted. In the current-flux-rotor position lookup table based rotor position estimation, the inherent current and flux-linkage ripple can cause the position estimation error. Instead of the conventional low-pass filter, the PLL based position interpolation technique is used for the better dynamic performance. The developed rotor position estimation scheme is realized using TMS320F2812 digital signal processor and prototype 1-hp SRM.

• ETRI Journal
• /
• 제37권5호
• /
• pp.906-916
• /
• 2015

High-speed I/O channels require adaptive techniques to optimize the settings for filter tap weights at decision feedback equalization (DFE) read channels to compensate for channel inter-symbol interference (ISI) and crosstalk from multiple adjacent channels. Both ISI and crosstalk tend to vary with channel length, process, and temperature variations. Individually optimizing parameters such as those just mentioned leads to suboptimal solutions. We propose a joint optimization technique for crosstalk cancellation (XTC) at DFE to compensate for both ISI and XTC in high-speed I/O channels. The technique is used to compensate for between 15.7 dB and 19.7 dB of channel loss combined with a variety of crosstalk strengths from $60mV_{p-p}$ to $180mV_{p-p}$ adaptively, where the transmit non-return-to-zero signal amplitude is a constant $500mV_{p-p}$.

• 한국공작기계학회논문집
• /
• 제10권5호
• /
• pp.78-84
• /
• 2001

The translation system is made up of springs, masses and a dashpot. This precise piece of equipment is controlled electro-mechanically by a motor and operating program. The control strategy of the system can be changed by spring stiffness, change of mass, and the damping coefficient of the dashpot. This system proves the necessity and effect of a closed loop control. In this paper, PD control experiments were implemented for the translation system. When the north falter was added on the PD controller, we compared the response characteristics of the two systems. The state feedback controller minimized scalar control gains and the resulting response characteristics of the system were studied using the LQR design. Finally, we improved the response characteristics of the translation system which are rising time, settling time, steady state error, and overshoot LQR was better as compared with PD control.