• 한국전기전자재료학회논문지
• /
• 제15권11호
• /
• pp.953-957
• /
• 2002

Single crystal 3C-SiC (cubic silicon carbide) thin-films were deposited on Si(100) wafer up to the thickness of 4.3 ${\mu}{\textrm}{m}$ by APCVD (atmospheric pressure chemical vapor deposition) method using HMDS (hexamethyildisilane; ｛CH$_{3}$｝$_{6}$ Si$_{2}$) at 135$0^{\circ}C$. The HMDS flow rate was 0.5 sccm and the carrier gas flow rate was 2.5 slm. The HMDS flow rate was important to get a mirror-like crystal surface. The growth rate of the 3C-SiC film was 4.3 ${\mu}{\textrm}{m}$/hr. The 3C-SiC epitaxial film grown on Si(100) wafer was characterized by XRD (X-ray diffraction), AFM (atomic force microscopy), RHEED (reflection high energy electron diffraction), XPS (X-ray photoelecron spectroscopy), and Raman scattering, respectively. Two distinct phonon modes of TO (transverse optical) near 796 $cm^{-1}$ / and LO (longitudinal optical) near 974$\pm$1 $cm^{-1}$ / of 3C-SiC were observed by Raman scattering measurement. The heteroepitaxially grown film was identified as the single crystal 3C-SiC phase by XRD spectra (2$\theta$=41.5。).).

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.13-19
• /
• 2012

In this study, ultrasonic vibration tool designed and made by using FEM analysis. And machining test was carried out in various machining conditions using ultrasonic vibration capable CNC machine. For work material, alumina ceramic ($Al_2O_3$) was used while for tool material diamond electroplated grinding wheel was used. To evaluate ultrasonic vibration effect, grinding test was performed with and without ultrasonic vibration in same machining condition. In ultrasonic mode, ultrasonic vibration of 20kHz was generated by HSK 63 ultrasonic actuator. The two grinding speeds, 1.67m/s and 3.35m/s, were applied. On the other hand, grinding forces were measured by KISTLER dynamometer.

• 대한조선학회논문집
• /
• 제30권4호
• /
• pp.112-126
• /
• 1993

본 논문에서는 선급규칙중 파랑하중 부분의 개정과 관련하여 선체종강도의 국제선급연합 통일규칙(IACS UR)을 검증하기 위하여 단기파랑하에서 비선형 파랑하중 해석을 수행하였고, 선체구조의 직접강도해석시에 사용하여야 할 지침으로 IACS WAVE DATA에 대한 검증을 수행하였다. 컨테이너선등과 같은 대형개구를 가진 선박의 응력을 구하기 위하여 수평전단력, 수평굽힘모멘트 및 비틂모멘트 산식을 일관성 있게 구하여 새로이 제시하였다. 또한 선체 외관에 작용하는 유체동압력을 선박의 길이 및 깊이방향에 대한 분포 산식으로 제시하였고 이를 타 선급 규칙과 비교, 검토하였다. 이상의 제시된 산식들은 각 선종, 크기 별로 17척 선박의 실선계산을 통하여 결정되었다. 이 산식들은 앞으로 선체구조부재 Scantling 산식이 결정되면 실선에 대한 적용계산을 통하여 검증될 것이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1995년도 추계학술대회논문집; 한국종합전시장, 24 Nov. 1995
• /
• pp.62-67
• /
• 1995

A method for determining impulsive responses and acoustic radiation for submerged shells of finite length has been presented. The method is a modal-based method, and uses a surface variational principle to obtain data in the frequency domain. The fast Fourier transform technique is used to convert the data to the time domain. The surface pressure responses of a cylindrical shell with endcaps wer compared with those of an infinite shell. It was shown that the surface pressures coincide exactly before any significant reflections from the endcaps occur. Traces of different types of waves were identified from the dispersion relations of the infinite shell. The contributions of flexural and longitudinal waves and these due to the direct radiation from the driving force to the fluid pressure were demonstrated using near-field plots. The exchange of energy between the shell and fluid was examined for shells with and without bulkheads. It was shown that a significant amount of the energy which enters the fluid returns to the shell and most of the energy is dissipated in the shell. It was also shown that the shell with bulkheads radiate significantly more energy into the far-field than the empty shell.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.359-362
• /
• 2006

This study develops an automatic berthing control algorithm for ships with a bow thruster and a stern thruster as well as a rudder. A nonlinear mathematical model for low speed maneuvering of ships is used to develop a MIMO(multi-input multi-output) nonlinear control algorithm. The algorithm consists of two parts, which are forward velocity control and heading angle control. The control algorithm is designed based on the longitudinal and yaw dynamic models of ships. The desired heading angle is obtained by the so called "Line of Sight" method. An optimal control force allocation method of the rudder and the thrusters is suggested. The nonlinear control algorithms are tested by numerical simulations using MATLAB, and shows good tracking performances.

• 한국전산유체공학회지
• /
• 제21권3호
• /
• pp.48-54
• /
• 2016

In the present work, numerical simulations were conducted on the scaled model of the BWB type UCAV in the subsonic region using ANSYS FLUENT V15. The prediction method was validated through comparison with experimental results and the effect of the twisted wing was investigated. To consider the transitional flow phenomenon, ${\gamma}$ transition model based on SST model was adopted. The coefficients of lift, drag and pitching moment were compared with experimental results and the pressure distribution and streamlines were investigated. The twisted wing decreases the lift force but increases lift-to-drag ratio through delay of stall and leading edge vortex's movement to the front, also the non-linearity of the pitching moment is decreased.

• 대한기계학회논문집B
• /
• 제27권9호
• /
• pp.1248-1255
• /
• 2003

Pressure coefficient in a rotating discharge hole was measured to gain insight into the influence of rotation on the discharge characteristics of rotating discharge holes. Pressures inside the hole were measured by a telemetry system that had been developed by the authors. The telemetry system is characterized by the diversity of applicable sensor type. In the present study, the telemetry system was modified to measure static pressure using piezoresistive pressure sensors. The pressure sensor is affected by centrifugal force and change of orientation relative to the gravity. The orientation of sensor installation for minimum rotating effect and zero gravity effect was found out from the test. Pressure coefficients in a rotating discharge hole were measured in longitudinal direction as well as circumferential direction at various rotating speeds and three different pressure ratios. From the results, the behaviors of pressure coefficient that cannot be observed by a non-rotating setup were presented. It was also shown that the discharge characteristics of rotating discharge hole is much more influenced by the Rotation number irrespective of pressure ratio.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.564-564
• /
• 2012

Graphene has been emerged as a fascinating material for future nanoelectronic applications due to its extraordinally electronic properties. However, their zero-bandgap semimetallic nature is a major problem for applications in high performance field-effect transistors (FETs). Graphene nanoribbons (GNRs) with narrow widths (${\geq}10nm$) exhibit semiconducting behavior, which can be used to overcome this problem. In previous reports, GNRs were produced by several approaches, such as electron beam lithography patterning, chemically derived GNRs, longitudinal unzipping of carbon nanotubes, and inorganic nanowire template. Using these methods, however, the width distribution of GNRs was a quiet broad and substantial defects were inevitably occurred. Here, we report a novel approach for fabricating width-tailored GNRs by focused ion beam-assisted chemical vapor deposition (FIB-CVD). Width-tailored phenanthrene ($C_{14}H_{10}$) templates for direct growth of GNRs were prepared on $SiO_2$/Si substrate by FIB-CVD. The GNRs on the templates were synthesized at $900-1,050^{\circ}C$ with introducing $CH_4$ $(20sccm)/H_2$ (10 sccm) mixture gas for 10-300 min. Structural characterizations of the GNRs were carried out using Raman spectroscopy, scanning electron microscopy, and atomic force microscopy.

• 한국결정학회:학술대회논문집
• /
• 한국결정학회 2002년도 정기총회 및 추계학술연구발표회
• /
• pp.3-3
• /
• 2002

Many studies on crystal growth mechanisms of the hen egg-white lysozyme protein crystals have mainly performed by optical microscopy and atomic force microscopy (AFM). As results, two types of growth mechanisms, which are a two-dimensional nucleation mechanism and a spiral growth mechanism, were identified. However, there was no direct evidence of grown-in screw dislocations at the spiral sites. We first observed the screw dislocations in tetragonal lysozyme crystals using synchrotron X-ray topography. In addition, to confirm the characteristics of dislocations, we have observed some elastic constants in lysozyme crystals in terms of the sound velocity measurement by pulse echo methods. Tetragonal hen egg-white lysozyme crystals were grown by the concentration gradient method. The crystals were grown in test tubes, with an inner diameter of 8 ㎜ and 80 ㎜ in length, held vertically. The test tubes were kept at 23C for 2 weeks. The maximum size of crystals were 3×3×4 ㎟. The high quality crystals were examined by Laue topography with a water filter using synchrotron radiation. Figure is a X-ray topograph. Several straight screw dislocations were observed. We also determined Burgers vector to be a [110] direction. The measurement of sound velocity was performed by the digital signal processing method. the crystals were placed in stainless steel vessel, which was filled with lysozyme solution used for crystal growth. We observed the longitudinal sound velocity along the [110] direction in the tetragonal is obtained to be 1817 ㎧. Therefore, Young modulus and shear modulus were evaluated to be 2.70 Gpa and 1.02 Gpa, respectively, if we assumed Poisson ratio is 0.33. These results will be discussed at the meeting.

• Journal of Welding and Joining
• /
• 제32권2호
• /
• pp.54-62
• /
• 2014

Manhole cover, which is usually made of grey cast iron and consists of frame and cover, should have enough strength to support the heavy traffic load. The manhole cover made of cast iron has heavy weight to handle manually and is vulnerable to impact force with its brittle characteristics. Moreover, its production process of casting has been regulated in terms of environmental pollution. In this study, steel manhole cover is proposed to substitute the cast cover with a series of structural analyses to confirm its strength to support the test load for manhole cover. The cover of the proposed steel manhole cover is made of thin circular pate and stiffeners below the plate. Rectangular columns and hollow circular plate were selected for the shape of the stiffener. In order to give enough strength for the cover to behave within elastic range in the loading, strengthening structures of the cover were varied with increasing the number and the size of the stiffeners. The results of the analyses revealed that when both the hollow circular stiffener and cross stiffeners were additionally applied at the same time to the steel cover with longitudinal stiffeners, the maximum stress level in the cover could be reduced to that level presented in the cast cover.