• 대한기계학회논문집A
• /
• 제27권2호
• /
• pp.223-230
• /
• 2003

Stress patterns are created in the plastic spur gear tooth body by introducing a hole or a steel pin to improve stress distribution. Static analysis using finite element method is carried out to show the effect. The result shows that maximum stress as well as tooth tip displacement is dependent on the size and location of a hole or a steel pin. When a hole located on the tooth center line, the maximum static stress level and the tooth tip deflection is always higher than that of a solid gear. But, a considerable reduction in the maximum stress and tooth tip displacement is achieved by insertion of steel pin.

• 대한방사선치료학회지
• /
• 제23권2호
• /
• pp.97-102
• /
• 2011

목 적: 2차원 배열 검출기를 이용하여 세기변조 방사선 치료 품질관리를 시행할 때 정량적 분석을 위한 감마(${\gamma}$) 함수의 적용은 일반적으로 연속적인 선량 분포에 대해 정의되어 있으나 임상적으로 불연속적인 지점에 대해 측정된 값이 이용되고 있으며 이는 감마(${\gamma}$) 지수법을 이용한 평가의 불확실성과 관련이 있을 것으로 사료된다. 본 논문은 두경부암 세기변조 방사선 치료 품질관리의 감마(${\gamma}$) 함수 적용에서 표본 추출 간격에 따른 감마(${\gamma}$) 지수 변화정도를 확인하고 불확실성을 평가하여 유효한 범위를 제시하고자 한다. 대상 및 방법: 본원에서 시행한 두경부 세기변조 방사선 치료 환자 10명을 대상으로 IBA Dosimetry사의 OmniPro I'mRT system software version 1.7b를 이용하여 동일한 두 선량 평가면(Plane)에 대해 분석을 시행하였다. 원점에 위치한 표본 추출 간격 0.1 cm의 선량 평가면을 기준으로 다른 하나의 선량 평가면 위치를 Y축 방향으로 0.0 cm, 0.2 cm, 0.5 cm, 1.0 cm씩 이동 시키면서 Gamma pass rate, Average signal, 측정값에 대한 표준편차의 변화를 관찰하였다. 이때 표본 추출 간격을 0.1 cm, 0.5 cm, 1.0 cm, 2.0 cm, 4.0 cm으로 변화시키면서 Y축 방향으로 동일한 거리를 이동했을 때 Gamma index의 변화를 실험하였다. 결 과: 각 표본추출 간격에 대해 Average signal의 차이는 0, -0.0019, -0.0004, -0.0460, -0.832로 나타났고 측정값에 대한 표준편차의 차이는 0, -0.0030, 0.0124, 0.0070, -0.0799로 나타났으며 Gamma pass rate의 차이는 0, 0.0027, -0.0143, 0.0532, 0.0560의 결과를 보였다. 표본추출 간격 0.1~1.0 cm 범위 내에서는 Average signal과 Gamma pass rate의 차이가 1.5% 이내로 나타났으며 2.0 cm 이상 범위에서는 5% 이상 차이를 보였다. 결 론: 감마(${\gamma}$) 함수의 적용에서 표본추출 간격이 1.0 cm 이하인 경우 실제 분석 값에 대해 1.5% 이내의 차이를 나타냈지만 2.0 cm 이상인 경우 Gamma pass rate이 실제 분석 값보다 5%이상 높게 나타났고 감마(${\gamma}$) 지수의 불확실성과 신뢰수준에 영향을 주었다. 세기변조 방사선 치료의 품질관리를 시행할 경우 표본추출 간격에 따른 감마(${\gamma}$) 지수의 불확실성을 고려하여 임상적으로 2.0 cm 미만의 표본 추출 간격이 적용되어야 할 것으로 사료된다.

• 한국농촌건축학회논문집
• /
• 제15권4호
• /
• pp.35-42
• /
• 2013

The study aims to investigate general characteristics of Jae-sil from an architectural perspective by grasping location, deployment, structure, and plan composition based on existing inhabited conditions in Jeollabukdo. Results derived from the study are as follows. First, the location of Jae-sil is classified into mountainous and village types, and the two types showed a similar distribution. The village type showed the most distribution in the foot of a mountain in the rear of village, while the mountainous type is close to graveyard. The Jae-sil were mostly exposed to south, southeast, and southeast, which was not significantly different from residence. For deployment of the Jae-sil, a "二" shaped house, where main quarter and gated building are parallel located, can be common, indicating that additional attached building is less required. Second, for the platform out of structural components, coursed masonry was conducted by using natural rocks, and placed were a prop on the platform, first line on processed foot stone, and others on natural foot stone. For pillar, front line round columns, while others square columns. The binding type of the upper part of pillar is dominated by jangyeosujang and sorosujang. For wooden frame structure, 5ryangs were the most distributed, and out of these, 1goju 5ryang was the most generally used. For a roof part, it was composed with gambrel roof with single eave, and the roof was constructed by placing traditional Korean tile roof on the top. Third, for a size of Jae-sil out of plan composition, although the facade and the side of it were presented in a diverse manner, 4 facade rooms and 1.5 side rooms were the most frequently presented, and all Jae-sil were equipped with front ceremonial space. For spatial composition of Jae-sil, main floored hall is placed at the center, and each room is placed on the left and right side to secure space for ancestral rite for participants of it, and for a house with 5 rooms or more, it shows that main floored hall and rooms are weighted from side to side.

• Journal of electromagnetic engineering and science
• /
• 제11권4호
• /
• pp.282-289
• /
• 2011

GHz electromagnetic interference (EMI) characteristics are analyzed for a 3dimensional (3D) stacked chip power distribution network (PDN) with through silicon via (TSV) connections. The EMI problem is mostly raised by P/G (power/ground) noise due to high switching current magnitudes and high PDN impedances. The 3D stacked chip PDN is decomposed into P/G TSVs and vertically stacked capacitive chip PDNs. The TSV inductances combine with the chip PDN capacitances produce resonances and increase the PDN impedance level in the GHz frequency range. These effects depend on stacking configurations and P/G TSV designs and are analyzed using the P/G TSV model and chip PDN model. When a small size chip PDN and a large size chip PDN are stacked, the small one's impedance is more seriously affected by TSV effects and shows higher levels. As a P/G TSV location is moved to a corner of the chip PDNs, larger PDN impedances appear. When P/G TSV numbers are enlarged, the TSV effects push the resonances to a higher frequency range. As a small size chip PDN is located closer to the center of a large size chip PDN, the TSV effects are enhanced.

• 한국방사선학회논문지
• /
• 제9권1호
• /
• pp.17-21
• /
• 2015

최근 고령화 사회에 접어들고 있는 의료현장에서 치아건강에 대한 관심이 커지면서 진단을 위한 치아 방사선 검사의 횟수가 증가하고 있다. 이는 국민 전체의 방사선피폭량 또한 증가하고 있다고 볼 수 있다. 또한 치과방사선에 대한 국민들의 방사선 피폭에 대한 관심도 증가하고 있어 치과 파노라마 촬영장치에 대한 기본 데이터 확보와 이에 대한 조사 및 선량의 측정이 필요하다. 본 연구에서는 ALOKA PDM-117 선량계를 이용하여 치과파노라마장치(VATEC Pax-400)에서 발생되는 2차원적인 선량분포도를 측정하고 그 분포에 대한 평가를 환자의 방사선피폭 차원에서 확인하였다. 치과파노라마장치의 선량분포는 치아부분 이외에도 턱과 안면부위에서 높았으며 산란선의 영향까지 고려한다면 방사선에 민감한 수정체에까지 불필요한 방사선의 피폭됨을 알 수 있었다. 본 연구 결과는 다양한 크기의 검사체와 선량 측정위치에서 보다 정확한 선량평가를 하는데 매우 유용하게 이용될 것으로 사료된다.

• Ocean and Polar Research
• /
• 제41권4호
• /
• pp.275-288
• /
• 2019

We investigated flux, grain size distribution, Nd-Sr isotope composition, mineral composition, and trace metal composition (REEs and Sc) of inorganic silicate fraction (ISF, mainly Asian dust with an unrestricted amount of volcanic materials) deposited during 600~1000 ka across the Mid-Pleistocene Transition at core NPGP 1401-2A (32°01'N, 178°59'E, 5205m) taken from the central part of the North Pacific. Our results reveal about a 2-fold increase in ISF flux after 800 ka, which is associated with an increase in La/Sc and a decrease in mean grain size. Asian dusts are finer than volcanic materials and La/Sc increases with the enhanced contribution of Asian dusts. Thus, increased flux after 800 ka can be explained by the increased contribution of Asian dusts relative to volcanic materials, likely due to an intensified Westerly Jet (WJ) and the drying of the Asian continent after the MPT. Mean grain size of ISF varies systematically in relation to glacial-interglacial cycles with a decrease during glacial stages, which is consistent with the previous results in the study area. Such a cyclical pattern is also attributed to the increase in the relative contribution of Asian dusts over volcanic components in glacial stages due to intensified WJ and drying of the Asian continent. Thus, it can be concluded that climate changes that had occurred across the MPT were similar to those of interglacial to glacial transitions at least in terms of the dust budget. Different from the Shatsky Rise, however, compositional changes associated with glacial-interglacial mean grain size fluctuations are not observed in Nd-Sr isotope ratios and trace element composition in our study of the Hess Rise. This may be attributed to the location of the study site far (> 4,000 km) from the volcanic sources. The volcanic component at the study site comprises less than 10% and varies within 3% over glacial-interglacial cycles. Such a small variation was not enough to imprint geochemical signals.

• Elastomers and Composites
• /
• 제51권4호
• /
• pp.263-268
• /
• 2016

In the polymer shaping process that uses molds, the quality of the molded products is determined not only by the flow of the (molten) polymer but also by the air venting in the cavity. Inadequate air venting in the cavity can cause defects in the product, such as voids, short shot, or black streaks. As it is critical to consider the location and size of the vents for proper venting of the air in the cavity, a method that predicts the flow of air and material is required. The venting of air by the flow of rubber inside the cavity was simulated by using a multi-phase computational fluid dynamics method. Through computer simulation, the interface of rubber and air over time was predicted. Then, the velocity and pressure distribution of the venting air were observed. Our research proposes a fundamental method for analyzing the multi-phase flow of polymer materials and air inside the cavity of a mold.

• 한국수산과학회지
• /
• 제56권5호
• /
• pp.676-683
• /
• 2023

The development of the egg, larvae, and juveniles of Acheilognathus macropterus from the Wicheon stream of Nakdonggang River was investigated for early life history characteristics. The fish used in the study were collected from Wicheon stream located in Bian-myeon, Uiseong-gun, Gyeongsangbuk-do. The fertilized egg was 1.88±0.09 mm (n=30) in long diameter and 1.34±0.06 mm (n=30) in short diameter. After fertilization at a water temperature of 20℃, the egg took 31 h and 40 min to hatch. Newly hatched larvae had an average total length of 3.92±0.13 mm (n=30) and possessed a yolk sac the mouth and anus were not developed. Twenty days after hatching, the postflexion larvae had an average total length of 8.08±0.29 mm (n=30), with the tail tip fully bent at 45° and began feeding. Thirty-three days after hatching, the number of fin stems reached an integer with an average total length of 15.0±1.08 mm (n=30). In this study, differences in the egg size, hatching time, melanophore development period, and distribution location were confirmed between A. macropterus and allied species.

• 한국지역지리학회지
• /
• 제2권2호
• /
• pp.159-171
• /
• 1996

본 연구는 심각해지는 토지문제를 해결하기 위해 최근에 시행되고 있는 여러가지 토지제도들이 효과적으로 운용되도록 지가를 정확히 산정하고자 하는 움직임에 대한 기초 연구로서, 다른 토지이용에 비해 월등 높은 지가를 보이고 중은 범위에서도 그 변동폭이 큰 상업지를 택하여, 상업지지가의 지역적 차이가 왜 발생하는지 알아보고자 하였다. $1989{\sim}1996$ 동안의 상업지역의 확산은 시 외곽에 빠르게 조성되고 있는 고밀도 아파트 단지를 배후지로 하여 주요 간선도로변을 따라 활발하게 이루어지고 있는 반면, 도심부는 영세한 부지규모 및 노후화한 건물들로 말미암아 급변하고 있는 상업환경의 변화에 능동적으로 대응하지 못하므로서 지가하락 현상을 보이고 있다. 상업지지가와 관련이 있으리라고 예상되는 6개 변수를 이용하여 중다희귀분석을 적용한 결과 보행자 통행량과 도심으로부터의 거리 등 두 변수가 상업지지가 변화량의 65% 정도를 설명해 주었다. 설명되지 않은 35%의 해명을 위해 잔차분석을 행한 결과 도심부의 과소예측, 시 외곽의 과대 예측을 읽을 수 있었는데 이는 광주시의 단핵구조적 특성의 반영일 뿐만 아니라 이 모델이 갖고 있는 한계이다.

• 설비공학논문집
• /
• 제19권9호
• /
• pp.662-668
• /
• 2007

In this study, jet fans are installed with 4 cases in the straight long tunnel; inlet-side setup, middle-side setup, outlet-side setup, and dispersion setup. A bus is selected as fired car, of which fire size is 20MW. And fired car locates at 100m, 700m, 1500m position from tunnel inlet, respectively. FLUENT, commercial finite-volume code, is used to analyze the performance. The velocity profile, $CO_2$ concentration, temperature distribution are examined for analysis. Performance of smoke control is compared by the backlayering length. Consequently, inlet-side setup of jet fans is a little more efficient than other cases considering the fire occurrence frequency in tunnel.