• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.50-56
• /
• 2006

Since most of small form-factor drives have a load/unload mechanism and the flying height of the head is getting lower as the capacity of disk drives increases, the load/unload velocity becomes one of the important factors to ensure the reliability of the load/unload mechanism. To control the load/unload velocity accurately, velocity sensing is essential. In this paper, we introduce a very practical method that acquires the load/unload velocity from the back electromotive force (BEMF) of a voice coil motor (VCM) and propose a calibration method for measuring the BEMF from a given circuit. Moreover, the effect of calibration error and temperature variation on the measurement of BEMF is shown by simulation. Then, this present method is applied to the load/unload velocity controller and is verified from the experimental result.

• 전기전자학회논문지
• /
• 제24권1호
• /
• pp.33-39
• /
• 2020

본 논문에서는 타이어의 물리적인 요소 중 하나인 압력정보를 이용해서 자동차의 하중 표출이 가능한 타이어 공기압 측정 기술을 사용한 차량의 적재중량 측정시스템 설계 기법을 제안한다. 제안된 기법은 하중 및 진동에 의한 노이즈 보정, 기체유량 보정, 데이터 믹서, 중량 환산 등의 4가지 과정으로 구성된다. 하중 및 진동에 의한 노이즈 보정에서는 외부충격 및 차량이 주행 중 발생하는 진동 등에 의해 타이어의 내부 압력이 상승하는 노이즈를 제거한다. 기체유량 보정 과정에서는 하중 및 진동에 의한 노이즈 보정 과정을 거친 데이터에 대하여 지면의 온도상승에 의해 타이어의 내부 압력이 상승하는 노이즈를 제거한다. 데이터 믹서 과정에서는 화물적재 시 타이어에 수직으로 전달이 되어 타이어의 압력변화에 따른 공차, 중차, 만차에 대한 하중과 압력 등을 분류하게 된다. 중량 환산 과정에서는 하중 및 진동에 의한 노이즈 보정 및 기체유량 보정을 거친 데이터를 사용하여 중량 환산 알고리즘을 통해 중량으로 표출된다. 중량 환산 알고리즘은 하중과 압력변화에 대한 선형 함수의 기울기인 중량 환산 Factor를 구하여 중량을 환산한다. 본 논문에서 제안된 타이어 공기압 측정 기술을 사용한 차량의 적재중량 측정 시스템의 정밀도를 평가하기 위해 자체적으로 테스트 베드를 구축하여 평가하였다. 하중 및 진동에 의한 노이즈 보정 결과와 기체 유량 데이터 보정 결과는 신뢰성 있는 결과를 나타내었다. 또한 중량 정밀도 반복 실험도 국내 업체 기준치인 90% 보다 우수한 중량 정밀도를 나타내었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 제17회 워크샵 및 추계학술대회
• /
• pp.706-710
• /
• 2005

포항공과대학교의 포항풍력에너지연구센터(PoWER Center)가 개발에 참여했던 750 kW급 직접구동형 국산화 풍력발전 시스템(KBP-750D)은 그 개발이 완료 단계에 이르러 설치를 준비하고 있으며 현재 KBP-750D의 상용화를 추진하기 위한 출력성능 및 하중 측정을 통한 실증연구가 진행되고 있다. IEC 61400-13의 규격을 기준으로 수행되는 하중 측정은 수개월간 지속되는 측정을 통한 방대한 하중 데이터 수집 과정과 데이터 검증, 데이터 분류, 시계열 해석, 하중 통계 해석, 주파수 분석, 하중 스펙트럼 해석과 등가하중 해석의 측정 데이터 처리 과정으로 구성된다. 본 연구에서는 하중 측정 데이터를 처리 해석함에 있어서 성력화를 도모하고 정확하면서도 객관적인 성능평가 자료를 확보하기 위하여, 하중 측정에 대한 전용 해석 프로그램의 개발을 추진하였다. 본 논문에서는 하중 측정 데이터에 대한 처리 및 해석 과정을 소개하고 해석 프로그램의 개발 과정 및 수행 결과를 보고한다.

• 한국농공학회지
• /
• 제38권1호
• /
• pp.90-97
• /
• 1996

In Korea, total sediment discharge of a river has been estimated simply by using certain sediment transport formulas including, among others, Einstein's formula. Those formular, however, are known not to be reliable enough for the result calculated by them to be used directly to river planning and management. Therefore, the study used the Modified Einstein Procedure to the estimation of total sediment discharge, because this method is reliable estimated by measurement. Here, measurement of sediment discharge used depth integrating method. The major results obtained from the study for estimation by depth integrating method of sediment discharge in Naeseong stream are as follow; 1 The sedeiment characteristics of Naeseong stream are; The distribution of sediment grain size shows that silt and clay are 55% and sand is 45%. and the bed load sediment grain size is constituted that sand contained with the grain size from O.062mm to 2.0mm is 80% 2. The sediment rating formulas derived from the regression analysis between the sediment discharge and flow discharge are; Seogpo-Gyo : Qs=$0.017 \times 10^{-4} Q^{2.352}$, where discharge is l0cms $0.074 \times 10^{-4} Q^{2.066}$, where discharge is l0cms

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.267-268
• /
• 2006

The cylinder cover stud of low-speed marine diesel engine is more than just a stud. It is a large structural element occasionally weighing over 200 kg used for assembling the combustion chamber components. Therefore, to understand the structural behavior of the stud and design it safely is quite important considering a catastrophic failure which can be arisen from an inadequate use of it. In this paper, the analysis results of the structural behavior of the stud is introduced. Strain measurement results compared with FE analysis results are summarized. The results showed that 1) the stud stress increased with engine operating load, 2) the maximum stress amplitude was about 10 MPa which is far smaller than the stud's fatigue strength of 61 MPa, 3) the stress ratio is higher than 0.9 and the stud's load factor is about 20 %, and 4) about 7 % of initial pressure tightening load was reduced while changing to a nut tightened condition.

• 한국소음진동공학회논문집
• /
• 제22권11호
• /
• pp.1089-1098
• /
• 2012

A faulting could be occurred at the end of deck by unexpected loads to bridge bearing after a bridge completion. Serviceability of bridges could be impaired by the faulting which is caused structural damage. Therefore, smart bridge bearing which can continuously observe the supporting points is needed. Some of bridge bearings have been developed for measuring vertical load and vertical displacement by installing sensors in the bearing. In those systems, however it is not easy to be replaced with new sensors when repairs are needed. In this study, the smart bridge bearing of which sensors can be replaced has been developed to overcome such a problem. In this study, strain signals were used for measuring both of vertical displacements and loads. FBG sensors(fiber optic Bragg-grating sensors) have been used for measurement of the strain signals since it is prevented from electronic noise by mediating light, enables the simplification of the measuring cable by multiple measurement, and is easy to place by lightweight and small size. The possibility of use was reviewed for smart bridge bearing based on FBG sensors through tests.

• 한국안전학회지
• /
• 제22권6호
• /
• pp.13-19
• /
• 2007

Diesel car's smoke measurement equipment and method were investigated based on the exhaust gas regulations. Reflection photo method and light extinction method for measuring smoke were compared under conditions of both no load mode and Lug-down 3 mode. Free acceleration mode at no load condition was used for regular inspection of diesel car, and Lug-down 3 mode was used for fine inspection of the diesel car. A correlation between no load mode and Lug-down 3 mode was investigated in this research. The smoke measured with reflection photo method was 1.5${\sim}$2 times higher than that of light extinction method The correlation coefficient between reflection photo method and light extinction method for measuring smoke was 0.83, which shows comparatively high correlation between the two methods for measuring smoke in diesel engines.

• 한국표면공학회지
• /
• 제54권4호
• /
• pp.171-177
• /
• 2021

This paper is concerned with the surface hardness measurement of NiP-coated AA7050 using different loads from 10 to 100 g. The surface hardness was observed to increase from 180 to 600 H_v with increasing NiP layer thickness, depending on the load applied for indentation. When NiP coating thickness is thinner than 2 ㎛, the surface hardness of NiP-coated AA7050 was mainly determined by AA7050 substrate, while it was significantly increased by NiP coating layer when NiP coating thickness is thicker than 2 ㎛. Hardness of AA7050 substrate itself was not dependent on the applied load but the hardness of NiP-coated AA7050 was largely influenced by the load applied for indentation. The largest difference of hardness between 10 g and 100g of applied loads, was obtained at the NiP thickness of about 8 ㎛ above which the measured hardness at 10 g reached a maximum value of about 600 H_v. It was also observed that indentation-induced plastic deformation next to the indented zone occurs when NiP layer is 5.64 times thicker than the depth of impression formed by indentation.

• 비파괴검사학회지
• /
• 제36권2호
• /
• pp.138-148
• /
• 2016

Measurement of elastic constants is crucial for engineering aspects of predicting the behavior of materials under load as well as structural health monitoring of material degradation. Ultrasonic velocity measurement for material properties has been broadly used as a nondestructive evaluation method for material characterization. In particular, pulse-echo method has been extensively utilized as it is not only simple but also effective when only one side of the inspected objects is accessible. However, the conventional technique in this approach measures longitudinal and shear waves individually to obtain their velocities. This produces a set of two data for each measurement. This paper proposes a simultaneous sensing system of longitudinal waves and shear waves for elastic constant measurement. The proposed system senses both these waves simultaneously as a single overlapped signal, which is then analyzed to calculate both the ultrasonic velocities for obtaining elastic constants. Therefore, this system requires just half the number of data to obtain elastic constants compared to the conventional individual measurement. The results of the proposed simultaneous measurement had smaller standard deviations than those in the individual measurement. These results validate that the proposed approach improves the efficiency and reliability of ultrasonic elastic constant measurement by reducing the complexity of the measurement system, its operating procedures, and the number of data.

• Journal of Electrical Engineering and Technology
• /
• 제10권1호
• /
• pp.83-91
• /
• 2015

This paper presents preventive and emergency control measures for on line transient stability (security) enhancement. For insecure operating state, generation rescheduling based on a real power generation shift factor (RPGSF) is proposed as a preventive control measure to bring the system back to secure operating state. For emergency operating state, two emergency control strategies namely generator shedding and load shedding have been developed. The proposed emergency control strategies are based on voltage magnitudes and rotor trajectories data available through Phasor Measurement Units (PMUs) installed in the systems. The effectiveness of the proposed approach has been investigated on IEEE-39 bus test system under different contingency and fault conditions and application results are presented.