• 한국안전학회지
• /
• 제36권5호
• /
• pp.27-35
• /
• 2021

This study investigated the change in stiffness and deflection of a scaffold working plate caused by damage to a cross-beam in the plate. Experiments were conducted considering various load and damage conditions of cross-beams. A cross-beam falling off from the working plate was considered damaged. The load-displacement curves of specimens at the center of the uniform load showed that the working plate stiffness decreased by 14.66%-1.89%, depending on the load interval due to the damage of one cross-beam. A reduction in the stiffness of 33.94%-40.76% resulted from the damage of two cross-beams. Moreover, the displacement increased by an average of 25% when one cross-beam was damaged and an average of 65% when two cross-beams were damaged. Therefore, damage to the cross-beam in the working plate can potentially cause accidents and harm workers. As the load increases, the risk of an accident due to the aforementioned damage also increases because the stiffness remarkably decreases with the load increase. Further, the damage to the cross-beam mainly reduces the stiffness but increases the displacement rather than the strength of the working scaffold plate.

• 한국안전학회지
• /
• 제12권4호
• /
• pp.230-240
• /
• 1997

본 연구에서는 폴리프로필렌 섬유보강 콘크리트의 파괴특성을 알아보기 위해 Monofilament 섬유와 Fibrillated 섬유의 두 종류 폴리프로필렌 섬유를 선택하여 10$\times$10$\times$50 cm 보 시편을 만들었는데, 이때 사용된 두 종류의 섬유 길이는 19 mm이고, 섬유 혼입량은 0%, 1%, 2%, 3%로 하였으며, 초기균열 깊이의 영향을 알아보기 위해 초기 균열길이를 각 섬유 혼입량에 따라 1.5cm, 3.0cm, 4.5cm로 하여 실험을 수행하였다. 또한, 본 연구에서는 폴리프로필렌 섬유보강 콘크리트의 파괴특성을 규명하기 위해 보 시편에 대한 4 점 하중 휨시험을 통해 하중-하중점 변위 곡선을 각 시편에 대해 측정하였고, 이때 COD 게이지를 이용하여 하중-CMOD 곡선도 측정할 수 있었다. 이러한 실험결과를 통해, 섬유혼입량과 초기 균열 깊이에 따른 압축강도, 휨강도 및 휨인성, 응력확대계수, 파괴에너지 등이 규명되었다. 이러한 결과에 대한 분석으로부터 Fibrillated 폴리프로필렌 섬유가 Monofilament 섬유보다 연성 효과가 큰 것을 알 수 있었으며, 특히 하중-CMOD 곡선으로부터 계산되는 파괴에너지인 Jc가 믿을만한 파괴특성 인자임을 알 수 있었다.

• 한국전산구조공학회논문집
• /
• 제23권2호
• /
• pp.227-234
• /
• 2010

탄소섬유시트로 보강된 철근콘크리트 보의 휨 거동을 조사하기 위해 하나의 기준보와 8개의 보강보(4개의 NU-보강보, 4개의 U-보강보)에 대한 휨 실험을 수행하였다. NU-보강보는 단부에 U 밴드를 적용하지 않은 보를, U-보강보는 U 밴드를 가진 보를 의미한다. 보강보 실험에서의 실험변수들은 탄소섬유시트의 보강겹수, U 밴드의 적용유무등이 있다. U 밴드를 가진 보강 시스템은 섬유시트의 계면박리 파괴를 지연시키고, U 밴드가 없는 보강시스템보다 나은 연성거동을 나타내 보였다. NU 보강보와 U 보강보 모두에서 섬유시트 겹수의 증가에 따라 최대하중과 휨 강성은 증가하였다. 실험결과들을 이론적인 비선형 휨 해석결과와 비교하였으며, 하중-처짐 선도 및 항복이전단계와 항복이후단계에서의 항복하중, 최대하중, 휨 강성 등이 잘 일치함을 확인하였다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2004년도 봄 학술발표회 논문집
• /
• pp.365-372
• /
• 2004

A new finite element model will be presented to analyze the nonlinear behavior of not only RC beams and slabs, but also RC beams strengthened by a patch repair. The numerical approach is based on the p-version degenerate shell element including theory of anisotropic laminated composites, theory of materially and geometrically nonlinear plates. In the nonlinear formulation of this model, the total Lagrangian formulation is adopted with large deflections and moderate rotations being accounted for in the sense of von Karman hypothesis. The material model is based on hardening rule, crushing condition, plate-end debonding strength model and so on. The Gauss-Lobatto numerical quadrature is applied to calculate the stresses at the nodal points instead of Gauss points. The validity of the proposed p-version finite element model is demonstrated through several numerical examples for the load-deflection curves, the ultimate loads, and the failure modes of reinforced connote slabs and RC beams bonded with steel plates or FRP plates compared with available experimental and numerical results.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1991년도 봄 학술발표회 논문집
• /
• pp.54-59
• /
• 1991

This experimental investigation was aimed at gathering information on the flexural properties, including ductility, of high-strength lightweight concrete members(concrete with a dry unit weight of approximately 1.85t/$\textrm{m}^3$ and with compressive strength approaching 630kg/$\textrm{cm}^2$ at 56days) under reversed cyclic loading. Two sets of six specimens each were manufactured using lightweght aggregate concrete having compressive strength of 350kg/$\textrm{cm}^2$ at 28days and 630kg/$\textrm{cm}^2$ at 56days. The test variables were the concrete strength, the amount of longitudinal reinforcement, and the spacing of ties. The test results, including hysteretic load-deflection curves, for the specimens representing columns under zero axial load are reported in this paper.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2003년도 학술발표논문집
• /
• pp.367-370
• /
• 2003

Lightweight polymer concrete with steel fiber can be used for thin panel, high building and large span structures due to its may advantages such as its durability, low weight, control of crack propagation, high strength and toughness. This study experimented about steel fiber reinforcement of lightweight polymer concrete using synthetic lightweight aggregate. The test result shows that the maximum strain and elastic modulus are in the range of $0.012{\sim}0.014\;and\;50.2{\times}10^3{\sim}51.0{\times}10^3kgf/cm^2$, respectively. The flexural load-deflection curves after maximum load are shown in smoothly with increase of steel fiber content

• 대한기계학회논문집A
• /
• 제33권12호
• /
• pp.1357-1365
• /
• 2009

In this study, we enhance the numerical approach of Lee et al.$^{(1)}$ to spherical indentation technique for property evaluation of hyper-elastic rubber. We first determine the friction coefficient between rubber and indenter in a practical viewpoint. We perform finite element numerical simulations for deeper indentation depth. An optimal data acquisition spot is selected, which features sufficiently large strain energy density and negligible frictional effect. We then improve two normalized functions mapping an indentation load vs. deflection curve into a strain energy density vs. first invariant curve, the latter of which in turn gives the Yeoh-model constants. The enhanced spherical indentation approach produces the rubber material properties with an average error of less than 3%.

• 한국지반공학회논문집
• /
• 제25권6호
• /
• pp.59-72
• /
• 2009

대구경 해상 말묵의 수평 하중전이 거동 및 변형 해석을 위해 p-y 하중전이 해석법이 널리 사용되고 있다. 그러나, 본 연구에서는, 기존의 p-y 해석법의 단점을 극복하여, 지반의 연속성을 고려한 수평방향 하중전이 해석을 고찰하였으며, 3D wedge failure mode의 이론적인 해법과 재하시험을 통해 말뚝의 실제 거동에 보다 부합되도록 연약지반의 p-y 곡선을 제안하였다. 제안된 하중전이함수법의 타당성을 검증하기 위하여 현장재하시험 사례와의 비교분석을 수행하였고, 그 결과 제안된 해석방법은 기존 p-y 곡선에 비해 대구경 해상말뚝의 거동 및 변형 특성을 적절히 예측함을 알 수 있었다.

• 대한기계학회논문집A
• /
• 제20권3호
• /
• pp.882-890
• /
• 1996

Mechanical properties, including Young's modulus, residual stress and rupture strength, of a thermally evaporated gold film have been measured form a blister test. In a theoretical study, the priniple of minimum potential energy and that of virtual work have been applied to the pressurized circular membrane problem, and load-deflection relations have been derived for typical membrane deflection mode of spheroidal shape. In an experimental study, circular gold membranes of 4800 A-thickness and 3.5mm diameter were fabricated by the silicon electropolishing technique. Mecahnical properties of the thin gold films were deduced from the load-deflection curves obtained by the blister test, Young's moduli, obtianed from blister test, have been in the range of 45-70 GPa, while those of bulk gold have been in the range of 78-80 GPa. Residual stresses in the evaporated gold films have been measured as 28-110MPa in tension, The rupture strength of the gold film has turned out to be almost equal to that of dental gold alloy (310-380MPa). It has been demonstrated that the present specimen fabrication method and blister test apparatus have been effective for simultaneous measurement of Young's modulus, residual stress and repture strength of thin solid films. Especially, the electropolishing technique employed here has provided a simple and practical way to fabricate thin membranes in a circular or an arbitrary shape, which could not be obtained by the conventional anisotropic silicon mecromachining technique.

• Steel and Composite Structures
• /
• 제13권3호
• /
• pp.239-258
• /
• 2012

In this paper, experimental investigations on high strength steel (HSS) stud connected steel-concrete composite (SCC) girders to understand the effect of shear connector density on their flexural behaviour is presented. SCC girder specimens were designed for three different shear capacities (100%, 85%, and 70%), by varying the number of stud connectors in the shear span. Three SCC girder specimens were tested under monotonic/quasi-static loading, while three similar girder specimens were subjected to non-reversal cyclic loading under simply supported end conditions. Details of casting the specimens, experimental set-up, and method of testing, instrumentation for the measurement of deflection, interface-slip and strain are discussed. It is found that SCC girder specimen designed for full shear capacity exhibits interface slip for loads beyond 25% of the ultimate load capacity. Specimens with lesser degree of shear connection show lower values of load at initiation of slip. Very good ductility is exhibited by all the HSS stud connected SCC girder specimens. It is observed that the ultimate moment of resistance as well as ductility gets reduced for HSS stud connected SCC girder with reduction in stud shear connector density. Efficiency factor indicating the effectiveness of high strength stud connectors in resisting interface forces is estimated to be 0.8 from the analysis. Failure mode is primarily flexure with fracturing of stud connectors and characterised by flexural cracking and crushing of concrete at top in the pure bending region. Local buckling in the top flange of steel beam was also observed at the loads near to failure, which is influenced by spacing of studs and top flange thickness of rolled steel section. One of the recommendations is that the ultimate load capacity can be limited to 1.5 times the plastic moment capacity of the section such that the post peak load reduction is kept within limits. Load-deflection behaviour for monotonic tests compared well with the envelope of load-deflection curves for cyclic tests. It is concluded from the experimental investigations that use of HSS studs will reduce their numbers for given loading, which is advantageous in case of long spans. Buckling of top flange of rolled section is observed at failure stage. Provision of lips in the top flange is suggested to avoid this buckling. This is possible in case of longer spans, where normally built-up sections are used.