• 한국분무공학회지
• /
• 제23권4호
• /
• pp.192-204
• /
• 2018

In this study, a 3D CFD analysis method for the combustion process was established for a low calorific value syngas-diesel dual-fuel engine operating under very lean fuel-air mixture condition. Also, the accuracy of computational analysis was evaluated by comparing the experimental results with the computed ones. To simulate the combustion for the dual-fuel engine, a new dual-fuel chemical kinetics set was used that was constituted by merging two verified chemical kinetic sets: n-heptane (173 species) for diesel and Gri-mech 3.0 (53 species) for syngas. For dual-fuel mode operations, the early stage of combustion was dominated by the fuel burning inside or near the spray plume. After which, the flame propagated into the syngas in the piston bowl and then proceeded toward the syngas in the squish zone. With the baseline injection system and piston shape, a significant amount of unburned syngas was discharged. To solve this problem, effects of the injection parameters and piston shape on combustion characteristics were analyzed by calculation. The change in injection variables toward increasing the spray plume volume or the penetration length were effective to cause fast burning in the vicinity of TDC by widening the spatial distribution of diesel acting as a seed of auto-ignition. As a result, the unburned syngas fraction was reduced. Changing the piston shape with the shallow depth of the piston bowl and 20% squish area ratio had a significant effect on the combustion pattern and lessened the unburned syngas fraction by half.

• 한국분무공학회지
• /
• 제24권1호
• /
• pp.35-42
• /
• 2019

Syngas is widely produced by incomplete combustion of coal, water vapor, and air (oxygen) in a high-temperature/high-pressure gasifier through a coal-gasification process for power generation. In this study, a simulation syngas which was mainly composed of $H_2$, CO, $CO_2$, and $N_2$ was fueled with diesel. A modified single cylinder compression ignition (CI) engine is equipped with intake port syngas supply system and mechanical diesel direct injection system for dual fuel combustion. Combustion and emission characteristics of the engine were investigated by applying various syngas composition ratios and compression ratios. Diesel fuel injection timing was optimized to increase indicated thermal efficiency (ITE) at the engine speed 1,800 rpm and part load net indicated mean effective pressure ($IMEP_{net}$) 2 to 5 bar. ITE of the engine increased with the $H_2$ concentration, compression ratio and engine load. With 45% of $H_2$ concentration, compression ratio 17.1 and $IMEP_{net}$ 5 bar, ITE of 41.5% was achieved, which is equivalent to that of only diesel fuel operation.

• Safety and Health at Work
• /
• 제9권4호
• /
• pp.416-420
• /
• 2018

Background: Urinary 1-hydroxypyrene (1-OHP) has been widely used as a biomarker of polycyclic aromatic hydrocarbons (PAHs) in occupationally exposed workers. The objective of this study is to investigate the concentration of urinary 1-OHP among charcoal workers as subjects and non-charcoal workers as controls. Methods: Early morning urine samples were collected from 68 persons (25 charcoal workers in Igbo-Ora, 20 charcoal workers in Alabata, and 23 non-charcoal workers) who volunteered to participate in this study. 1-OHP determination in urine samples was carried out using high performance liquid chromatography after hydrolysis. Descriptive and inferential statistics were used for data analysis at p < 0.05. Results: The mean urinary 1-OHP concentration (${\mu}mol/mol$ creatinine) among charcoal workers at Igbo-Ora and Alabata and non-charcoal workers were $2.22{\pm}1.27$, $1.32{\pm}0.65$, and $0.32{\pm}0.26$ (p < 0.01). There existed a relationship between respondent type and 1-OHP concentration. Charcoal workers were 3.14 times more at risk of having 1-OHP concentrations that exceed the American Conference of Governmental Industrial Hygienists guideline of $0.49{\mu}mol/mol$ creatinine than non-charcoal workers (relative risk = 3.14, 95% confidence interval: 1.7-5.8, p < 0.01). Conclusion: Charcoal workers are exposed to PAHs during charcoal production and are at risk of experiencing deleterious effects of PAH exposure. Routine air quality assessment should be carried out in communities where charcoal production takes place. Assessment of urinary 1-OHP concentration and use of personal protective equipment should also be encouraged among charcoal workers.

• 한국융합학회논문지
• /
• 제12권2호
• /
• pp.29-34
• /
• 2021

본 논문에서는 중심에 동공을 갖는 원통형태 광결정 도파로가 제안되어지고, 이 전송로의 도파 특성에 대한 분석이 수행되어진다. 여기서 동공은 일반적인 공기이거나 임의의 액체나 고체 물질들에 의한 저지수 유전체로써 형성되게 된다. 베셀 함수를 이용한 분석적 방법으로 전자장에 대한 엄밀한 해를 구하기 위하여, 행렬 기법이 고유치 방정식의 유도에 사용되고, 실효 굴절률, 분산, 전자장 분포 등의 기본 모드의 중요한 전송 성질들이 조사된다. 또한 분석 결과 정확도의 검증을 위하여 엄밀한 완전 벡터 유한 차분법을 적용해보고, 광결정 도파로의 설계와 제조 상의 문제를 해결하는데 용이하게 활용하고자 한다. 설계된 중심-동공 광도파관의 실효 모드 면적이 2.6056 ㎛2에서 5.9673 ㎛2까지 동작 파장에 따라 다양하게 변하며, 일반적으로 광도파로의 중심으로부터 바깥쪽으로 원통형의 층수가 적을수록 그리고 굴절률 n1이 약간 큰 저지수일수록 실효 면적은 작아지므로, 비선형 소자 응용의 관점에서 훨씬 더 최적화된 결과를 나타낸다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제13권1호
• /
• pp.554-565
• /
• 2021

Air bubble entrainment is a phenomenon that can significantly reduce the efficiency of liquid motion in piping systems. In the present study, the bubble formation mechanism in a globe valve with 90% water fraction flow is explained by visualization study and pressure oscillation analysis. The shadowgraph imaging technique is applied to illustrate the unsteady flow inside the transparent valve. This helps to study the effect of bubbles induced by the globe valve on pressure distribution and valve flow coefficient. International Society of Automation (ISA) recommends locations for measuring pressure drop of the valve to determine its flow coefficient. This paper presents the comparison of the pressures at different locations along with the upstream and the downstream of the valve with the values at recommended positions by the ISA standard. The results show that in partially filled pipe flow, the discrepancies in pressure between different measurement locations in the valve downstream are significant at valve openings less than 30%. The aerated flow induces the oscillation in pressure and flow rate, which leads to the fluctuation in the flow coefficient of the valve. The flow coefficients have a linear relationship with the Reynolds number. For the same increase of Reynolds number, the flow coefficients grow faster with larger valve openings and level off at the opening of 50%.

• 한국추진공학회지
• /
• 제26권1호
• /
• pp.47-59
• /
• 2022

리세스 길이가 다른 4개의 와류동축형 분사기를 적층제조 방식으로 제작하였다. 상압 환경에서 물과 공기를 모사추진제로 하여 단일분사 및 혼합분사 수류실험을 수행하였다. 리세스 길이와 추진제 유량 조건에 따른 분사차압과 유량계수를 확인하였고, 이미지 분석을 통해 분열길이와 분무각을 측정하였다. 혼합분사 분사차압 및 유량계수 결과에서 액체 분사기는 리세스에 영향을 받지 않았다. 하지만 기체 분사기는 리세스 길이 증가에 따라 분사차압이 증가하고 유량계수가 감소하였다. 단일분사 시 분열길이는 리세스 증가에 따라 길어졌지만, 혼합분사에서는 반대로 감소하였다.

• 한국분무공학회지
• /
• 제27권3호
• /
• pp.117-125
• /
• 2022

This study examines whether engine fuel efficiency is improved by optimization of the exhaust valve timing in a state where the intake valve timing has been optimized in a small turbo gasoline engine that has intake cams and exhaust cams with fixed valve opening periods. When the exhaust valve is opened late, the expansion stroke is longer, and the efficiency can be improved. A 2-cylinder turbo gasoline engine with 0.8 liters of displacement and an MPI (Multi Point Injection) fuel system was used. The engine was operated at 1,500 and 3,000 rpm, and the load conditions included a partial load of 50 N·m and a high load of 70 N·m. Data was recorded as the exhaust valve timing was controlled, and this was used to calculate the efficiency of combustion using a heat release, the fuel conversion efficiency, and the pumping loss. Results and the hydrocarbon concentrations in the exhaust gas were compared for each condition. Experiment results confirmed that additional fuel efficiency improvements are possible through exhaust valve timing control at 1,500 rpm and 50 N·m. However, in other operating conditions, fuel efficiency improvements could not be obtained through exhaust valve timing control because cases where the pumping loss and fuel/air mixture slip increased when the exhaust valve timing changed and the fuel efficiency declined.

• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.629-637
• /
• 2023

This study aimed to evaluate the effect of post-curing equipment and time on the flexural strength of 3D printing resins produced by a liquid crystal display(LCD) printer. The three 3D printing resins(DENTCA Denture Teeth, DT; C&B 5.0 hybrid, CH; C&B Permanent A2, CP) were divided into four groups according to post-curing time(10 min and 30 min) and equipment with or without vacuum treatment. For the three-point flexural strength test and biaxial strength test were prepared by method according to ISO 10477, ISO 6872, respectively. Flexural strength was measured with universal testing machine. Comparison between post-curing time of each post-curing equipment was analyzed by independent sample t-test and Mann-Whitney U test(α=.05), and comparison between groups according to each 3D printing resin was performed by Kruskal-Wallis test and post-hoc by Bonferroni-Dunn test(α=.05). The flexural strength of the resin post-curing under vacuum was higher than that of the resin post-curing in air. In the comparison according to the post-curing time, in the case of the post-curing equipment without vacuum, the 30 minute curing time showed significantly higher flexural strength than the 10 minute curing time, except for the biaxial flexural strength of CH(P<.05). In the post-curing equipment with vacuum, the three-point flexural strength of all 3D printing resins(DT, CH, and CP) showed a higher value at 30 minute curing time than at 10 minute curing time.

• 한국분무공학회지
• /
• 제29권2호
• /
• pp.68-74
• /
• 2024

As awareness of environmental pollution problems increases worldwide, interest in air pollutants is increasing. In particular, NOx and PM, which are major pollutants in diesel vehicles, are contributing significantly to emissions. As a result, its importance is increasing. In this study, based on research results applied to large diesel vehicles, the problem of natural regeneration caused by low exhaust gas temperature during low speed and low load operation is solved by applying a complex regeneration DPF that is not affected by temperature conditions to small diesel vehicles. The feasibility of application to small diesel vehicles was reviewed by measuring the emission reduction efficiency. As a result of the engine test, the power reduction rate and fuel consumption rate before and after device installation under full load conditions were 2.9% decrease and 3.5% increase, respectively, satisfying the standard for a 5% reduction, and as a result of the regeneration equilibrium temperature (BPT) test, the regeneration temperature was 310℃. appeared at the level. The reduction efficiency test results for the actual vehicle durability test equipment showed 97.3% PM, 51.0% CO, and 31.1% HC, while the city commuter vehicle had PM 97.5%, CO 61.7%, HC 40.0%, and the school bus vehicle had PM 96.8%, CO 44.4%, HC 34.3%, and low-speed logistics vehicles showed a reduction efficiency of 98.2% for PM, 36.0% for CO, and 45.7% for HC. Based on the results of this study, in the future, it is necessary to secure DPF technology suitable for all vehicle types through actual vehicle application research on temperature condition-insensitive composite regenerative DPF for medium-sized vehicles.

• Nuclear Engineering and Technology
• /
• 제55권11호
• /
• pp.3973-3982
• /
• 2023

As for two-phase flow in rectangular channels, the flow regimes especially like churn-turbulent and annular flow are significant for the physical problem like Countercurrent Flow Limitation (CCFL). In this study, the rectangular channels with cross-sections of 4 × 66 mm, 6 × 66 mm, 8 × 66 mm are adopted to investigate the flow regimes of air-water vertical upward two phase flow under adiabatic condition. The gas and liquid superficial velocities are 0 ≤ j_g ≤ 20m/s and 0.25 ≤ j_f ≤ 3m/s respectively which covering bubbly to annular flow. The flow regimes are identified by random forest algorithm and the flow regime maps are obtained. As the results, the transitional void fraction from slug to churn turbulent flow fluctuate from 0.47 to 0.58 which is significantly affected by the dimensional size of channel and flow rate. Besides, the void fraction at transitional points from churn-turbulent (slug) to annular flow are 0.66-0.67, which are independent with the gap size. Furthermore, a new criteria of slug to churn-turbulent flow is established in this study. In addition, by introducing the interfacial force model, the criteria of churn-turbulent (slug) flow to annular flow is verified.