• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.4
• /
• pp.415-424
• /
• 2004

Cooling the electronic equipment is one of the major focal points of the design process and the key to successful product launch. The two-phase loop thermosyphone which is a good candidate among many available options was investigated fur cooling of the high power amplifiers. The system is composed of evaporator which contains 6 parallel cold plates, fan cooled condenser, gas-liquid separator, and interconnecting tubes. Experiments were performed for several refrigerant charging values, hs and as a experiment result, the optimum charging value fur this system was proposed. In order to optimize the system design, the operating cycle pressure and inlet/outlet temperatures of evaporator and condenser are measured and analyzed. The effect of the three parameters such as flow rate and temperature of condenser cooling air, and thermal load on the evaporator are investigated. The lower the operating pressure and the cycle temperatures are also better to prevent the leakage of the system. The system invesigated in this paper can be directly used for cooling of a real unmanned wireless communication station.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.2
• /
• pp.53-59
• /
• 2004

In this paper, we propose a new multi-purpose Scanning Force Microscope (SFM) system. The system can be used for nano/micro-scratching, in-process profile measurement, and observation of potential surface defects which occur during the scratching in air or liquid. Experimental results of nano/micro-scratching show that the smallest scratching depth can be controlled to be 10nm, which corresponds to the stability of the SFM system. Profile measurements of nano/micro-scratching surfaces have also been performed by the method of on-machine measurement and in-process measurement. Two measurement results were in good agreement with each other. The maximum difference was approximately 10 nm, which was mainly caused by the sampling repeatability error that influences the measurement accuracy Also, micro-defects on the micro-scratching surface were successfully detected by the SFM system. It was confirmed that the number of micro-defects increases when the surface is subjected to a cyclic bending load. The maximum depth was less than 100nm.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.11 no.2
• /
• pp.108-115
• /
• 1991

A field experiment was conducted to evaluate the effects of cattle compost application on the change of soil physical properties and their relationship to yield performance of selected main forage crops. Maize(CV. Suweon 19) and sorghum hybrids(CV. Pioneer 9'31) as a summer crops and winter rye were grown on newly reclaimed red yellow soils(Fine loamy, Typic Hapludults) under different application rate of cattle compost associated with chemical NPK fertilization, from Oct. 1986 to Sept. 1989. Experimental field was laid down as a split plots design with four replications. The results obtained are summarized as follows: 1. Cattle compost application reclaimed soil physical propeties, such as formation of granular structure and water holding capacity, and it result in a great increase of plant growth and the rate of dry matter accumulation. 2. While cattle compost treatment reduced the portion of soild phase of the three phase constituents of soils, it increased the portion of air phase and liquid phase comparatively. 3. Organic matter, N, P, K, and mineral content in soil were markedly increased in the plot treated with compost. 4. Cattle compost application increased fodder production both in maize-rye and sorghum hybrids-rye cultivation. Annual dry matter yield of maize-rye cropping was 2183(NI'K only), 2425(NPK+compvst 3000 kg) and 2800kg/lOa(NPK + compost 6000kg/10a).

• Asian Journal of Atmospheric Environment
• /
• v.10 no.2
• /
• pp.90-98
• /
• 2016

Total suspended particulates (TSP) in the atmosphere were collected for 2 weeks during winter in Muroran, Hokkaido, Japan, a typical iron-manufacturing city. The concentrations of polycyclic aromatic hydrocarbons (PAHs) and nitropolycyclic aromatic hydrocarbons (NPAHs) in TSP were determined by high-performance liquid chromatography (HPLC) using fluorescence and chemiluminescence detectors, respectively. No relationship was observed between the atmospheric PAH and NPAH concentration, or the atmospheric PAH and TSP concentration. However, there was a tendency that the atmospheric PAH concentration was higher when the wind blew from the coke-oven plant. Furthermore, the concentration ratios of 1-nitropyrene to pyrene, which is a suitable indicator of the contribution made by automobiles and coal combustion systems to urban air particulates, were smaller in Muroran and the values were close to those observed in particulates from coal combustion systems. Therefore, these results show that the PAH and NPAH compositions for Muroran are characteristic of an iron-manufacturing city.

• Journal of Animal Environmental Science
• /
• v.12 no.1
• /
• pp.29-34
• /
• 2006

The effects of turning frequency were examined on the efficiency of composting lime treated excess sludge amended with sawdust from the activated sludge process after a liquid/solids separation process. The raw and excess sludge from the activated sludge process associated with the hog wastewater treatment system is a significant problem and composting is an effective method far reducing the pollution potential of hog wastewater sludge. The coagulant used sludge composting and ammonia emissions from composting are not well established. The effect of compost properties such as high total carbon, C/N ratio and pH value on performance of composting sludge and biofiltration of ammonia from composting process were investigated. The ammonia emission was not significantly increased during composting. The ammonia concentrations of the exhaust air of composter were ranged from 0.5 and 7 ppm about 12 days after composting. The performance of the hog wastewater sludge composting was the most sensitive to chemical treated sludge properties such as high total carbon and high C/N ratio of the initial compost mixes. Temperature in compost and ammonia emission were not greatly affected by the turning frequency.

• Journal of the Korean Society of Combustion
• /
• v.7 no.4
• /
• pp.1-9
• /
• 2002

The morphology of deposits on $15-{\mu}m$ thin SiC filaments has been investigated with SEM and compared with UV-excited laser induced broadband fluorescences in co-flowing, propane laminar diffusion flames in a reduced oxidizer environment. The homogeneous morphology of droplet-like deposits inner flame zone and the agglomeration of condensed-phase deposits and the transition to soots from grown up droplet-like precursors with approaching the flame surface can be observed in a barely sooting flame. The average size of the mature soots deposited in the luminous flame edge is scarcely dependent on their axial position in a confined flame under reduced oxidizer condition. A double structure of PAH fluorescence is observed in near-extinction flames with further decreasing of oxidizer. A comparison of the PAH fluorescence with the morphologies of deposits indicates that appearance of the "dark" hollow zone is caused by a decreased number density of developed liquid-phase large molecules and the outer weak fluorescence zone is caused by the diffusion of gas-phase small molecules.

• Journal of the Korean Institute of Gas
• /
• v.19 no.3
• /
• pp.18-24
• /
• 2015

The flash point is one of the most important indicators of the flammabiliy of liquid solutions. The flash point is the lowest temperature at which there is enough concentration of flammable vapor to form an ignitable mixture with air. In this study the flash points of binary flammable solutions, 2-propanol+propionic acid and n-hexanol+formic acid systems, were measured using Seta flash closed cup tester. Particularly n-hexanol+formic acid system exhibited minimum flash point behavior. The measured values were compared with the calculated values using Raoult's law and optimization method. The calculated data by optimization method described the measured values more effectively than those calculated by Raoult's law.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.10
• /
• pp.778-782
• /
• 2009

Recently, we developed a simple thermopneumatic micropump having neither a membrane nor a valve. This micropump discharges liquid by a thermopneumatic pressure and refill by a capillary attraction. In case of the micropump driven by the capillary attraction, the flow characteristic depends mainly on the geometry of the micropump. In this paper, we investigated the influence of the geometry of the micropump on the performance of the micropump to illustrate the properness of the micropump shape. We analyzed the micropump characteristics of six types having different geometries by FVM simulation with a commercial CFD tool. Also we fabricated the micropumps with PDMS and glass by micromachining, and tested the performances. The simulation and the test results illustrate that the discharge volume and the discharge time depend on the chamber volume. The expansion angle of the inlet channel location has influence on the refill time, while the front air channel direction has influence on the backward flow loss.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.4
• /
• pp.59-66
• /
• 2007

In this paper, experimental investigation results of the effect of partial admission ratio on the performance of axial turbine was presented. A supersonic impulse turbine of gas generator cycle liquid rocket engine turbopump was used for the test. for experimental purpose, a nozzle block, in which total 14 number of axi-symmetric convergent-divergent nozzles are arranged circumferentially, was designed and manufactured. Partial admission ratio was controlled by changing the number of active nozzles. High pressure air was used as working medium for the test. The experimental result revealed that the performance of the supersonic impulse turbine does not much affected by the partial admission ratio for supersonic impulse turbine.

• Environmental Engineering Research
• /
• v.20 no.4
• /
• pp.377-382
• /
• 2015

The high concentration of nitrogen and phosphorus in wastewater incorporated with the ability to use carbon dioxide as the carbon source make the microalgae become more attractive in wastewater treatment process. This study evaluates the optimal conditions for the digestion of settelable solids from the recirculating aquaculture system to produce the biomass of the green microalga Scenedesmus sp. After solids separation, aerobic digestion of settleable solids under disperse condition produced nitrate as the final product of consequently ammonification and nitrification processes. With the optimal digestion procedure, nitrate concentration during aerobic digestion in 2000 mL vessel increased from $9.63{\pm}0.65mg\;N/L$ to $58.66{\pm}0.06mg\;N/L$ in 10 days. Thereafter, cultivation of Scenedesmus sp. was performed in 1000 mL Duran bottle with air bubbling. The highest Scenedesmus sp. specific growth rate of $0.321{\pm}0.01/d$ was obtained in treatment using liquid fraction after aerobic digestion as the whole culture medium for Scenedesmus sp. cultivation. With this study, digestion of $8,800{\pm}128.12mg\;dry\;weight/L$ of settleable solids from fish pond finally produced $1,235{\pm}21mg\;dry\;weight/L$ of Scenedesmus sp. biomass.