• 융합신호처리학회논문지
• /
• 제4권3호
• /
• pp.55-60
• /
• 2003

위치제어 시스템이나 속도제어 시스템의 제어기 설계에서는 항상 기계적인 시스템의 유연성이 고성능에 대한 제약요소로 작용한다. 회전축으로 연결된 대부분의 기계적 시스템은 자체 회전자 관성과 부하 관성으로 이루어진 2관성 시스템이며, 이들 관성에 의해 회전축에는 비틀림이 발생한다. 이들 비틀림 현상은 회전 맥동 및 진동을 발생한다. 비틀림 진동을 억제하기 위하여 많은 연구가 행해져 왔다. 본 연구에서는 CDM을 이용하여 전압제어형 직류전동기 2관성 시스템의 속도제어기를 설계한다. 먼저 CDM을 적용한 제어기 설계가 용이하도록 전압제어형 직류전동기 2관성 시스템의 모델을 구한다. 그 후 CDM 표준형을 적용한 적정한 제어기를 설계한다. 설계된 속도제어 시스템은 시뮬레이션과 실험을 통하여 그 타당성이 검토된다.

• Nuclear Engineering and Technology
• /
• 제55권7호
• /
• pp.2604-2612
• /
• 2023

Spent nuclear fuel and long-lived radioactive waste must be carefully handled before disposing them off to a geological repository. After the pre-storage period in water pools, spent nuclear fuel is stored in casks, which are widely used for interim storage. Interim storage in casks is very important part in the whole cycle of nuclear energy generation. This paper presents the results of the numerical study that was performed to evaluate the thermal behavior of a metal-concrete CONSTOR RBMK-1500 cask loaded with spent nuclear fuel and placed in an open type interim storage facility which is under fire conditions (steady-state, fire, post-fire). The modelling was performed using the ANSYS Fluent code. Also, a local sensitivity analysis of thermal parameters on temperature variation was performed. The analysis demonstrated that the maximum increase in the fuel load temperatures is about 10 ℃ and 8 ℃ for 30 min 800 ℃ and 60 min 600 ℃ fires respectively. Therefore, during the fire and the post-fire periods, the fuel load temperatures did not exceed the 300 ℃ limiting temperature set for an RBMK SNF cladding for long-term storage. This ensures that fire accident does not cause overheating of fuel rods in a cask.

• 한국공간구조학회논문집
• /
• 제23권1호
• /
• pp.45-52
• /
• 2023

This study proposes an RCS composite damping device that can achieve seismic reinforcement of existing buildings by dissipating energy by inelastic deformation. A series of experiments assessing the performances of the rubber core pad, hysteretic steel slit damping device, and hybrid RCS damping device were conducted. The results showed that the ratios of the deviations to the mean values satisfied the domestic damping-device conformity condition for the load at maximum device displacement in each direction, at the maximum force and minimum force at zero displacement, as well as the hysteresis curve area. In addition, three analysis models based on load-displacement characteristics were proposed for application to seismic reinforcement design. In addition, the validity of the three proposed models was confirmed, as they simulated the experimental results well. Meanwhile, as the shear deformation of the rubber-core pad increased, the hysteretic behavior of super-elasticity greatly increased the horizontal force of the damping device. Therefore, limiting the allowable displacement during design is deemed to be necessary.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제17권9호
• /
• pp.2377-2398
• /
• 2023

In our daily lives, we engage in a variety of tasks that rely on our senses, such as seeing. Blindness is the absence of the sense of vision. According to the World Health Organization, 2.2 billion people worldwide suffer from various forms of vision impairment. Unfortunately, blind people face a variety of indoor and outdoor challenges on a daily basis, limiting their mobility and preventing them from engaging in other activities. Blind people are very vulnerable to a variety of hazards, including falls. Various barriers, such as stairs, can cause a fall. The Internet of Things (IoT) is used to track falls and send a warning message to the blind caretakers. One of the gaps in the previous works is that they were unable to differentiate between falls true and false. Treating false falls as true falls results in many false alarms being sent to the blind caretakers and thus, they may reject the IoT system. As a means of bridging this chasm, this paper proposes an intelligent shoe that is able to precisely distinguish between false and true falls based on three sensors, namely, the load scale sensor, the light sensor, and the Flex sensor. The proposed IoT system is tested in an indoor environment for various scenarios of falls using four models of machine learning. The results from our system showed an accuracy of 0.96%. Compared to the state-of-the-art, our system is simpler and more accurate since it avoids sending false alarms to the blind caretakers.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2004년도 봄 학술발표회 논문집
• /
• pp.161-168
• /
• 2004

This study describes the behavior and failure probability of basic structural member in case of fire for the research of safety assessment on onshore structure. Fire safety assessment can be done by comparing fire resistance of members with fire severity of heat load For more Practical applications, the commercial structural analysis program is linked with the in-house code and gets the limiting temperature by analyzing structural strength of member with elasto-plastic analysis and large deflection analysis. AFOSM method is utilized to obtain the failure probability against the fire. The examples of rather simple structures such as beams and plates are applied to explain and verify the procedure of fire safety assessment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 추계학술대회 논문집 학회본부
• /
• pp.171-174
• /
• 1991

Among the various PWM methods, the hysteresis-band current control PWM method is popularly used because of its simplicity of implementation, fast response characteristics and inherent peak current limiting capability. However, the current control PWM method with a fixed hysteresis-band has the disadvantage that switching frequency decreases and current ripple is high as the increasing of back-EMF. As a result, load current contains excess harmonics. This paper describes a adaptive hysteresis-bandwidth control algorithm so as to maintain the average switching frequency constant and decrease the current ripple where the hysteresis bandwidth is derived as a relation with the switching frequency. This control algorithm is applied to the surface-type brushless DC motor with separated winding and using the computer simulation, the validity of its algorithm is proved.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1358-1365
• /
• 2010

A case study deals with Squeezing behavior under tunneling. Squeezing stands for large time-dependent convergence during tunnel excavation. Squeezing can occur in both rock and soil as long as the particular combination of induced stresses and material properties pushes some zone around the tunnel beyond the limiting shear stress at which creep starts. Under squeezing rock conditions, If the support installation is delayed the rock mass moves into the tunnel and a stress redistribution takes place around it. On the contrary, if deformation is restrained, squeezing will lead to long-term load build-up of rock support. This paper shows analysis case mutually with monitoring and numerical analysis result of squeezing behavior of Pinglin tunnel in Taiwan.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1203-1205
• /
• 1992

Due to poor energy resources, the importance of energy saving has been greatly emphasized. It can be one method of energy saving to reduce the power. The AC adjustable speed drive systems show excellent efficiency, which have been developed in recent years. The adjustable speed drive system improves the efficiency in lightly load condition and extend the life span of motor by limiting the over-current at starting. The main topic of study is the results of energy saving and emergency transfer.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권10호
• /
• pp.470-476
• /
• 2005

In this paper PU control scheme is presented. The proposed scheme has following features. The one is oft-starting method which is used for preventing to flow large current in motor phase winding when motor starts. The ther is the selection of the level of the over current. The first feature is implemented by increasing the PWM duty lowly, the second feature is implemented by limiting the magnitude of the phase current level by which the over heat f motor by copper losses and magnetic saturation decreases. By the analysis using FEM considering load condition, the peed of mode transition from PW to single pulse control is selected and confirmed by simulation that there is no ver current occurs during the mode transition. For the verification of proposed scheme, the simulation using MATLAB Simulink with considering non-linearity of inductance profile from FEM analysis is performed and the experiment with SRM drive system which has the DSP controller and single Phase SRM are peformed.

• 전자공학회논문지A
• /
• 제33A권2호
• /
• pp.50-58
• /
• 1996

This paper proposes the channel-access protocol suitable to a very high speed photonic WDM network with star configuration, which can provide a high channel utilization and insensitivity to the propagation delay. The proposed protocol employs a control channel and a simple status table to deal with the propagation delay which has been a major limiting factor in the performance of the very high speed optical communication networks. The control channel transmits control information in order to reserve access on data channels, and each node constitutes a status table after the reception of control pckets which holds information about the availbility of destination node and data channel. The proposed protocol is insensitive to the propagation delay time by removing necessity of the retransmission and by allowing parallel transmission of control packet and data packets. It is proved in analysis and discrete event simulation that the proposed protocol is superior in throughput and mean delay, especially at the high load conditions compared to the existing high speed channel-access protocols.