• Wind and Structures
• /
• v.35 no.3
• /
• pp.147-155
• /
• 2022

This research proposes a wind-lens turbine design that can startup and operate at a low wind speed (< 5m/s). The performance of the wind-lens turbine was investigated using CFD and wind tunnel testing. The wind-lens turbine consists of a 3-bladed horizontal axis wind turbine with a diameter of 0.6m and a diffuser-shaped shroud that uses the suction side of the thin airfoil SD2030 as a cross-section profile. The performance of the 3-bladed wind-lens turbine was then compared to the two-bladed rotor configuration while keeping the blade geometry the same. The 3-bladed wind-lens turbine successfully startup at 1m/s and produced a torque of 66% higher than the bare turbine, while the two-bladed wind-lens turbine startup at less than 4m/s and produced a torque of 186 % higher than the two-bladed bare turbine at the design point. Findings testify that adding the wind-lens could improve the bare turbine's performance at low wind speed.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.9
• /
• pp.1348-1358
• /
• 1989

We analyzed electrostatic lens with axi-symmetic configurations using the analytic equation for a single apertured lens. The developed computer code afforded to estimate ion optical properties such as ion trajectories, aberrations and ion beam diameters, and was found to have advantages of a shorter calculation time. The calculated ion optical properties for several types of electrostatic lens were in good agreement with Burghard's ones and it was seem that 20% reduction of ion beam diameter could be obtained by the change of aperture diameters.

• Journal of Korean Ophthalmic Optics Society
• /
• v.14 no.3
• /
• pp.29-35
• /
• 2009

Purpose: To develop a relay lens type scope with 70 mm eye relief. Methods: By using Sigma 2000 design program, we designed and manufactured a relay lens type scope with 70 mm eye relief, which is integrated after designing an objective part with relay lenses and an eyepiece part, respectively. Results: The characteristics of the relay lens type scope with 70 mm eye relief whch is designed and manufactured by methods, which integrate after respectively designing an object part with relay lenses and an eyepiece part, have the magnification of $+4{\times}$,the length from 1st lens to last lens of about 105 mm, the barrel diameter of 18mm, and the effective diameter of 13 mm. Also we know that the resolution line width is 275 cycles/rad at the 30% MTF value criterion. Conclusions: We could design and manufacture the relay type scope with 70 mm eye relief, the characteristics of which have the magnification of $+4.0{\times}$the MTF above 30% at 275 cycles/rad, and the length from 1st lens to last lens of about 105 mm.

• Development and Reproduction
• /
• v.10 no.2
• /
• pp.93-96
• /
• 2006

The total length, head length, head height, eye diameter, retina thickness, and lens diameter of the dotted gizzard shad, Konosirus punctatus, showed positive allometric relationships between hatching and 30 days post-hatching (dph). The increase in total length relative to head length and head height, head length growth relative to eye and lens diameter, head height growth relative to eye diameter and lens diameter, and thickness of the retina relative to eye diameter, lens diameter, head length, and head height were showed allometric relationships. The eyes were formed completely at 9 dph. At this age, the eye has a lens, an optic nerve fiber layer, a ganglion cell layer, an inner plexiform layer, an inner nuclear layer, an outer plexiform layer, an outer nuclear layer, an outer limiting membrane, a rod and cone layer, and an epithelial layer. The essential demands that must be met by the retina in this species pertain to light sensitivity and spatial resolution.

• Korean Journal of Optics and Photonics
• /
• v.5 no.2
• /
• pp.204-211
• /
• 1994

Micro array lens systems are designed for a faximile or copy machine. The array type is hexagonal. Diameter of a lens is 0.16 mm and the distance of the center of the nearest neighbor is 0.192 mm. The magnitude of the lens system is 1:1. Working distane is 10.55 mm and the spot size is less than 0.04 mm radius on axis and 0.20 mm off-axis in case of single layer system. Working distance is 7.90 mm and the spot size is less than 0.07 mm radius on axis and 0.09 mm radius off axis in case of double layer system. Performance of single layer micro array lens system and double layer micro array lens system are compared with the characteristics of the ray fans.y fans.

• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.11-17
• /
• 2001

In this paper, spherical Luneburg lens antennas have been systematically analyzed using the Eigenfunction Expansion Method (EEM), The developed technique has capability of performing a complete 3-D analysis to characterize the multi-layered dielectric spherical lens with arbitrary permittivity and permeability. This paper describes the analysis technique, and presents the results of the parametric study of Luneburg lens antennas by varying design parameters suoh as the diameter of the lens antenna (up to 80 wavelength), number of spherical shells (up to 30 shells), air-gaps between spherical shells, and dielectric loss of the material. Many representative engineering design curves including the far-field patterns, wide-angle sidelobe characterizations, antenna efficiency have been presented.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.165-174
• /
• 2006

The autotstigmatic null lens system is designed and constructed for the fabrication of a parabolic mirror with the diameter of 450 mm(f/2.7). And the measurement reliability is also analyzed theoretically by means of the tolerancing technique using lens design software(CODE V). From this analysis, we can precisely fabricate a parabolic mirror with the large diameter of 450 mm(f/2.7). Meanwhile, in order to confirm the fabrication results by the autostigmatic method, the mirror surface is tested again by an autocollimating method that uses only a plane mirror without any null lens.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.20 no.1
• /
• pp.113-122
• /
• 2002

We designed the illumination optical system to use Fresnel lens which is the most general type of large aperture system. The normal construction of Fresnel lens is a thin molded piece of material, usually some kind of plastic, with one side flat and the other comprising a series of concentric segments each angled in a way to provide for optimum focusing for a pair of conjugate points. The 155 mm Marine Signal Lantern is the approved for use on buoys and a maximum omnidirectional range of 8 nmi, can be obtained with standard 12V equipment, respectively. Finally, Fresnel lens with 155 mm diameter was designed and evaluated. Also, we re-designed groove "out" of Fresnel lens and compared results of groove "in" type with groove "out" type. According to the results, Fresnel lens is obtained best optical results when grooved side faces the longer conjugate.de faces the longer conjugate.

• 연구논문집
• /
• s.25
• /
• pp.105-113
• /
• 1995

Fresnel lenses are developed for flat optics with the optical characteristics close to aspherical lens such as sharp focusing and dispersion instead of spherical or aspherical surface. Usually, these fresnel lenses and diffraction gratings are machined by high-energy beam such as electron beam machining, but recently with the development of ultra precision machine tool and machining technology, 3-dimension micro machining becomes preferable. This study on the micro machining of fresnel lens is carried out to develop the basic technology of ultra precision micro machining. The machined lens mold will be used for the manufacturing of fresnel lens with 120mm focal distance using synthetic resin material with 1.49 refractive index(PMMA), and the shape of lens is 48mm diameter, $300\mum$ pitch and about $5-700\mum$depth of groove in brass.

• Journal of fish pathology
• /
• v.16 no.2
• /
• pp.75-80
• /
• 2003

Red scabream, Pagrus major , is a valuable aquaculture species in Korea , but spontaneous eye abnormality occurred in cultured individuals . The incidence of eye abnormality was 4% in the group of cultured red scebream. The abnormality was characterized by unilateral and bilateral exophthalmos, opacity and lens pathology. Lense prolapse was found in two cases. Lenses in diseased fishes was considerably small in diameter and eyes were deformed as a whole. In the group of induced hybrid red scabream Pagrus major (♀) x black seabrearn Acanthopagrus schlegeli (♂), the incidence of eye abnormality wa~ the same 4%, but only opacity was registered. Opacity was also found in two of sixteen examined Wild-caught red seabrcam. Histopathological changes of lenses in cultured red seabreem included vecuolated cytoplasm of lens fibers, necrosis of fibers in central part of lens, folding and increase in thickness of lens capsule, and epithelial proliferation beneath the anterior lens capsule. In affected eyes no parasites or gas bubbles were found.