• Transactions on Electrical and Electronic Materials
• /
• v.3 no.2
• /
• pp.28-31
• /
• 2002

The Cdl-xZnxTe film was fabricated by thermal evaporation for the flat-panel X-ray detector. The stoichimetric ratio and the crystal structure of a polycrystalline Cd$_{1-x}$ Zn$_{x}$Te were investigated by EPMA and XRD, respectively. The leakage current and X-ray sensitivity of the fabricated films were measured to analyze the X-ray response characteristic of Zn in the polycrystalline CdZnTe thin film. The leakage current and the output charge density of Cd$_{0.7}$Zn$_{0.3}$Te thin film were measured to 0.37 nA/cm$^2$ and 260 pc/cm$^2$ at an applied voltage of 2.5 V/${\mu}{\textrm}{m}$, respectively. Experimental results showed that the increase of Zn doping rates in Cd$_{1-x}$ Zn$_{x}$Te detectors reduced the leakage current and improved the signal to noise ratio significantly.

• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1060-1066
• /
• 1997

In this paper, the effects of La addition of PLZT thin film prepared by sol-gel method on the capacitor characteristics are investigated for gigabit generation DRAM applications. The addition of La on the PLZT capacitor results in a trade-off between charge storage density(Qc') and leakage current density(Jl). As La content increases, Qc' and permeability(εr) at 0V are reduced while Jl is significantly decreased. It is demonstrated that 5% La doping of PZT can substantially reduce Jl and also improve resistance to fatigue while incurring only minimal degradation of Qc'. Very low leakage current density (5×10-7 A/㎠ even at 125℃) and high charge storage density (100fC/㎛2) under VDD/2=1V conditions are achieved using 5% La doped PZT thin films for gigabit DRAM capacitor dielectrics. In addition, the fatigue and TDDB measurements indicate good reliability of the PLZT capacitors.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.4
• /
• pp.153-156
• /
• 2007

Structural and electrical properties of the fully crystallized-bismuth magnesium niobate ($Bi_2Mg_{2/3}Nb_{4/3}O_7$, BMN) films with 15 mol% excess bismuth deposited on Pt bottom electrode by pulsed laser deposition are characterized for various deposition temperatures. The BMN films were crystallized with a monoclinic structure from $300^{\circ}C$ and the surface roughness slightly decreases with increasing deposition temperature. The capacitance density of the films increases with increasing deposition temperature and especially, films deposited at $400^{\circ}C$ exhibit a capacitance density of approximately $620nF/cm^2$. The crystallized BMN films with approximately 170 nm thickness exhibit breakdown strength above 600 kV/cm (${\leq}10V$) irrespective of deposition temperature and a leakage current density of approximately $2{\times}10^{-8}A/cm^2$ at 590kV/cm (at 10 V).

• Applied Science and Convergence Technology
• /
• v.23 no.2
• /
• pp.90-96
• /
• 2014

Flexible $ZrO_2$ films as dielectric materials for high-energy-density capacitors were deposited on polyethylene terephthalate (PET) substrates by RF magnetron sputtering. The growth behavior, microstructure and electrical properties of the flexible $ZrO_2$ films were dependent on the sputtering pressure and gas ratio. Although $ZrO_2$ films were deposited at room temperature, all films showed a tetragonal crystalline structure regardless of the sputtering variables. The surface of the film became a surface with large white particles upon an increase in the $O_2/Ar$ gas ratio. The RMS roughness and crystallite size of the $ZrO_2$ films increased with an increase in the sputtering pressure. The electrical properties of the $ZrO_2$ films were affected by the microstructure and roughness. The $ZrO_2$ films exhibited a dielectric constant of 21~38 at 1 kHz and a leakage current density of $10^{-6}{\sim}10^{-5}A/cm^2$ at 300 kV/cm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.125-128
• /
• 1999

(Ba$_{0.6}$Sr$_{0.4}$)TiO$_3$(BST) thin films were fabricated with different deposition temperature by Pulsed Laser Deposition(PLD). This BST thin films showed a maximum dielectric constant value of $\varepsilon$$_{r}$=~684 and dielectric loss was ~0.01 when substrate temperature was 75$0^{\circ}C$. Charge storage density of BST thin film was 4.733 [$\mu$C/$\textrm{cm}^2$] and estimated charging time was 0.15 nsec. Leakage current density of BST thin film was below 10$^{-7}$ [A/$\textrm{cm}^2$] at 3V. 3V.V.

• ETRI Journal
• /
• v.13 no.2
• /
• pp.21-27
• /
• 1991

Effects of annealing on the dielectric properties and microstructures of thin tantalum oxide film(25nm) deposited on p-type Si substrate with rf reactive magnetron sputtering were investigated. The leakage current density was remarkably reduced from $10^-8$ to $10^-12$ A/$\mum^2$at the electric field of 2MV/cm after rapid thermal annealing(RTA) in $O_2$at $1000^{\circ}C$, while little leakage reduction was observed after furnace annealing in $O_2$ at $500^{\circ}C$. The structural changes of thin tantalum oxide film after annealing were examined using high resolution electron microscope(HREM). The results of HREM show that substantial reduction in the leakage current density after the RTA in $O_2$ can be attributed to crystallization and reoxidation of the thin amorphous tantalum oxide film.

• The Journal of Information Technology
• /
• v.7 no.2
• /
• pp.69-76
• /
• 2004

This paper presents the results of spectral analysis about waveforms and leakage current waveforms on contaminated silicon insulators under various environment conditions.(salt fog, clean fog, rain). The larger the leakage current during 200ms, the higher the power spectrum at 60Hz. If contaminated insulators suffers from high salt density fog, the leakage current occurs with high crest value intermittently, results in the low spectrum. Analysis of leakage current data showed that this electrical activity was characterized by transient arcing behavior contaminants are deposited on the insulator surface during salt fog tests. This provides a path for the leakage current to flow along the surface of the insulator. It is important to have an indication of the pollution accumulation in order to evaluate the test performance of a particular insulator. If the drop in surface resistivity is severe enough, then the leakage current may escalate into service interrupting flashover that degrade power quality.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.2
• /
• pp.334-340
• /
• 1997

Electric and dielectric properties of the $SrTiO_3$films have been studied. The influence of impurities on $SrTiO_3$ films was evaluated to reduce the leakage current density. Acceptor doping, with a small concentration of Fe or Cr, has led to a substantial improvement to $10^{-9}$ order in the leakage current density. The experimental results can be explained by a model in which oxygen vacancies are the key defects responsible for the leakage current. The $SrTiO_3$ film 200 nm in thickness with 5 mol% excess SrO fabricated in $Ar/O_2$ at $550^{\circ}C$ obtained the lowest leakage current density $1.0 {\times} 1.0 A/\textrm{cm}^2$. The improved results can be introduced into the capacitor dielectric of giga bit DRAM memories.

• Journal of the Korean Ceramic Society
• /
• v.32 no.7
• /
• pp.761-768
• /
• 1995

Double layered BaTiO3 thin films with high dielectric constant as well as good insulating property were prepared for the application to low voltage driving thin film electroluminescent (TFEL) device. BaTiO3 thin films were formed by rf-magnetron sputtering technique. Amorphous and polycrystalline BaTiO3 thin films were deposited at the substrate temperatures of room temperature and 55$0^{\circ}C$, respectively. Two kinds of films prepared under these conditions showed high resistivity and high dielectric constant. The figure of merit (=$\varepsilon$r$\times$Eb.d) of polycrystalline BaTiO3 thin film was very high (8.43$\mu$C/$\textrm{cm}^2$). The polycrystalline BaTiO3 showed a substantial amount of leakage current (I), under the high electric field above 0.5 MV/cm. The double layered BaTiO3 thin film, i.e., amorphous BaTiO3 layer coated polycrystalline BaTiO3 thin film, was prepared by the new stacking method and showed very good dielectric and insulating properties. It showed a high dielectric constant fo 95 and leakage current density of 25 nA/$\textrm{cm}^2$ (0.3MV/cm) with the figure of merit of 20$\mu$C/$\textrm{cm}^2$. The leakage current density in the double layered BaTiO3 was much smaller than that in polycrystalline BaTiO3 under the high electric field. The saturated brightness of the devices using double layered BaTiO3 was about 220cd/$m^2$. Threshold voltage of TFEL devices fabricated on double layered BaTiO3 decreased by 50V compared to the EL devices fabricated on amorphous BaTiO3.

• Korean Journal of Materials Research
• /
• v.28 no.2
• /
• pp.118-123
• /
• 2018

5 nm-thick $SiO_2$ layers formed by plasma-enhanced chemical vapor deposition (PECVD) are densified to improve the electrical and interface properties by using nitric acid oxidation of Si (NAOS) method at a low temperature of $121^{\circ}C$. The physical and electrical properties are clearly investigated according to NAOS times and post-metallization annealing (PMA) at $250^{\circ}C$ for 10 min in 5 vol% hydrogen atmosphere. The leakage current density is significantly decreased about three orders of magnitude from $3.110{\times}10^{-5}A/cm^2$ after NAOS 5 hours with PMA treatment, although the $SiO_2$ layers are not changed. These dramatically decreases of leakage current density are resulted from improvement of the interface properties. Concentration of suboxide species ($Si^{1+}$, $Si^{2+}$ and $Si^{3+}$) in $SiO_x$ transition layers as well as the interface state density ($D_{it}$) in $SiO_2/Si$ interface region are critically decreased about 1/3 and one order of magnitude, respectively. The decrease in leakage current density is attributed to improvement of interface properties though chemical method of NAOS with PMA treatment which can perform the oxidation and remove the OH species and dangling bond.