• Applied Microscopy
• /
• 제48권4호
• /
• pp.130-131
• /
• 2018

Electron channeling contrast imaging (ECCI) is one of the imaging techniques in scanning electron microscopy based on a variation in electron backscattering yield depending on the direction of the primary electron beam with respect to the crystal lattice. The ECCI provides not only observation of the distribution of individual grains and grain boundaries but also identification of the defects such as dislocations, twins, and stacking faults. The ECCI at the interface between recrystallized and deformed region of shot peening treated nickel clearly demonstrates the microstructural evolution during the recrystallization including original grain boundaries, and thus can provide better insight into the recrystallization behavior.

• Bulletin of the Korean Chemical Society
• /
• 제11권4호
• /
• pp.339-342
• /
• 1990

$Gd_2O_3-ThO_2$ solid solutions containing 8,10 and 12 mol % $ThO_2$ were synthesized with spectroscopically pure $Gd_2O_3,$ and $ThO_2$ polycrystalline powders. X-ray diffraction revealed that all synthesized specimens have the modified fluorite structure, and the lattice parameter of $Gd_2O_3$ is nearly unchanged with increasing $ThO_2$ mol %. Both ac and dc conductivities were measured in the temperature range $500-1100^{\circ}C$ under $Po_2's$ from $10^{-6}$ to $10^{-1}$ atm. The dc conductivities are nearly independent of $Po_2,$ and agree with the ac values. This implies that the solid solutions are ionic conductors. The conductivity increases with increasing $ThO_2$ mol % with an average activation energy of 1.23 eV. An oxygen interstitial defect and ionic hopping conduction are suggested.

• 한국초전도ㆍ저온공학회논문지
• /
• 제18권4호
• /
• pp.15-20
• /
• 2016

The effects of electron beam (EB) irradiation on the superconducting critical temperature ($T_c$) and critical current density ($J_c$) of YBCO films were studied. The YBCO thin films were irradiated using a KAERI EB accelerator with an energy of 0.2 MeV and a dose of $10^{15}-10^{16}e/cm^2$. A small $T_c$ decrease and a broad superconducting transition were observed as the EB dose increased. The value of $J_cs$ (at 20 K, 50 K and 70 K) increased at doses of $7.5{\times}10^{15}$ and $2.2{\times}10^{16}e/cm^2$. However, $J_cs$ decreased as the dose increased further. The X-ray diffraction (XRD) analysis showed that the c axis of YBCO was elongated and the full width at half maximum (FWHM) increased as the dose increased, which is strong evidence of the atomic displacement by EB irradiation. The transmission electron microscopy (TEM) showed that the amorphous layer formed in the vicinity of the surfaces of the irradiated films. The amorphous phase was often present as an isolated form in the interior of the films. In addition to the formation of the amorphous phase, many striations running along the a-b direction of YBCO were observed. The high magnification lattice image showed that the striations were stacking faults. The enhancement of $J_c$ by EB irradiation is likely to be due to the lattice distortion and the formation of defects such as vacancies and stacking faults. The decrease in $J_c$ at a high EB dose is attributed to the extension of the amorphous region of a non-superconducting phase.

• 한국표면공학회지
• /
• 제48권6호
• /
• pp.253-259
• /
• 2015

The test equipment becomes more important with the development of semiconductor industry. MEMS probe is an important testing component to detect the defects from the generated electric signal when it contacts the metal pad of semiconductor devices. Ni-Pd alloy has been paid attention to as a candidate of MEMS probe material because of its high surface hardness and relatively low resistivity. In this study, electroplated Ni-Pd alloy has been prepared by using ethylene diamine as a complexing agent. Solid solution alloy coating could be formed when concentration of palladium chloride and current density were in the ranges of 1~5 mM and $0.2{\sim}1.5A/dm^2$, respectively. The increase of current density brought about an decrease in palladium content, which made both of lattice parameter and grain size smaller. As a result of grain refinement, high hardness could be obtained. However, surface cracking was observed due to residual stress when the current density was above $1.3A/dm^2$. When effects of heat treatment temperature on hardness and sheet resistance were investigated, the accompanied grain growth decreased both of them. The decrease of hardness remained stable at a temperature of $200^{\circ}C$. The sheet resistance was drastically reduced at $100^{\circ}C$. After that, it was found to become constant.

• 한국재료학회지
• /
• 제8권7호
• /
• pp.634-640
• /
• 1998

HBr을 이용한 트렌치 식각시 식각 방지막의 형성과 이들이 결함 생성 및 분포에 미치는 영향을 고분해능 투과전자현미경을 이용하여 연구하였다. $O_2$ 및 다른 첨가 가스로 $SiO_xF_y$, $SiO_xBr_y$ 등의 식각 방지막을 표면에 형성시켜 벽면 undercut을 방지하고 표면의 거칠기를 감소할 수 있었으며, 이후의 트렌치 채움 공정에서 void 가 없는 잘 채원진 구조를 얻을 수 있었다. 형성된 식각 방지막은 격자 결함의 생성 및 이들의 분포에 영향을 미쳤다. 대부분의 식각 유도 결함들은 트렌치 바닥의 가장자리에서 $10\AA$ 이내의 깊이로 분포하였으며, 잔류막의 두께에 의존하였다. 두꺼운 잔류막층 아래로는 결함들이 거의 사라졌으며, 결함층의 깊이와 잔류막 두께는 대체로 반비례하는 것을 나타났다. 기판 내에 존재하는 결정학적인 결함들은 식각종의 입사각이나 에너지에 의존하는 반면에,식각된 표면에서 관찰되는 결함들은 트렌치 식각동안 형성되는 이러한 잔류막의 두께에 크게 의존하는 것으로 나타났다.

• 한국결정성장학회지
• /
• 제9권2호
• /
• pp.162-167
• /
• 1999

3가지 방향성을 가진 사파이어 기판 위에 GaN 박막을 OMVPE방식으로 증착시켜 증착된 GaN epilayer를 투과전자현미경으로 분석하여 각 미세구조의 차이를 비교분석하였다. 3 가지 방향 모두에서 GaN 증착층이 관찰되어졌으며 그중 가장 좋은 경계면의 상태와 단일결정성을 보여준 것은 사파이어{0001} 방향의 기판을 사용한 경우였다. 결함들도 {0001} 방향의 기판을 사용한 경우에서 가장 적게 나타났다. 모든 경우에서 buffer layer는 발견되어지지 않았고 그럼에도 불구하고 경계면에서의 격자 뒤틀림이 일어나는 지역이 수 나노미터(nanometer) 정도밖에 안되는 우수한 경계면들이 관찰되었다. 따라서 일반적으로 GaN 박막 증착시에 가장 많이 사용되는 사파이어 basal plane 외에도 결함이 많기는 하지만, {1120}와 {1102} plane 위에도 GaN 증착층이 buffer layer 없이 증착 될 수 있다는 사실을 TEM 관찰을 통하여 알 수 있었으며 사파이어 {0001}면를 기판으로 사용한 경우에 미세구조 측면에서 볼 때 hetero-epitaxial한 GaN 박막층을 얻을 수 있는 것을 확인하였다.

• Bulletin of the Korean Chemical Society
• /
• 제34권11호
• /
• pp.3335-3339
• /
• 2013

Boron-doped ZnO (BZO) nanorods were grown on quartz substrates using hydrothermal synthesis, and the temperature-dependence of their photoluminescence (PL) was measured in order to investigate the origins of their PL properties. In the UV range, near-band-edge emission (NBE) was observed from 3.1 to 3.4 eV; this was attributed to various transitions including recombination of free excitons and their longitudinal optical (LO) phonon replicas, and donor-acceptor pair (DAP) recombination, depending on the local lattice configuration and the presence of defects. At a temperature of 12 K, the NBE produces seven peaks at 3.386, 3.368, 3.337, 3.296, 3.258, 3.184, and 3.106 eV. These peaks are, respectively, assigned to free excitons (FX), neutral-donor bound excitons ($D^{\circ}X$), and the first LO phonon replicas of $D^{\circ}X$, DAP, DAP-1LO, DAP-2LO, and DAP-3LO. The peak position of the FX and DAP were also fitted to Varshni's empirical formula for the variation in the band gap energy with temperature. The activation energy of FX was about ~70 meV, while that of DAP was about ~38 meV. We also discuss the low temperature PL near 2.251 eV, related to structural defects.

• 반도체디스플레이기술학회지
• /
• 제21권2호
• /
• pp.123-126
• /
• 2022

We investigated deep levels in n-type 4H-SiC epitaxy layer of the Positive-Intrinsic-Negative diode and Schottky barrier diodes by using deep level transient spectroscopy. Despite the excellent performance of 4H-SiC, research on various deep level defects still requires a lot of research to improve device performance. In Positive-Intrinsic-Negative diode, two defects of 196K and 628K are observed more than Schottky barrier diode. This is related to the action of impurity atoms infiltrating or occupying the 4H-SiC lattice in the ion implantation process. The I-V characteristics of the Positive-Intrinsic-Negative diode shows about ~100 times lower the leakage current level than Schottky barrier diode due to the grid structures in Positive-Intrinsic-Negative. As a result of comparing the capacitance of devices diode and Schottky barrier diode devices, it can be seen that the capacitance value lowered if it exists the P implantation regions from C-V characteristics.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1996년도 The 9th KACG Technical Annual Meeting and the 3rd Korea-Japan EMGS (Electronic Materials Growth Symposium)
• /
• pp.526-526
• /
• 1996

The single crystal of LiTaO3 is well known eletro-optic material as well as the piezoelectric one applied to SAW filter. LiTaO3 has large electro-optic effects, so applied to optical switch, acosto-optic deflector, and optical memory device using photorefractive effects. The crystal growth of SAW-grade LiTaO3 has been studied many aspects, but there is no detail research about optic-grade crystal growth. The conditions of optic-grade LiTaO3 single crystal are as below. The optical transmittance must be over 75%, and axial and radial concentratiom uniformity below 1%. The variation of Curie temperature depending on Li/Ta ratio must be also below 2$^{\circ}C$ and no internal no internal cracks and defects. Because of the limitation of crystal quality, the growing of optic-grade LiTaO3 single crystal is very difficult compared with the growing of SAW-grade. In this research, upper conditions of optic-grade single crystal was investigated after growing of 1 inch diameter and 1.5 inch length LiTaO3 single crystal having no internal cracks and defects using Czochralski method. Curie temperature was determined with DSC and measuring capacitance and lattice parameter was calculated about the grown crystal and ceramic powder samples of various Li/Ta ratio. The result of Tc variation was below 1.2$^{\circ}C$ all over the grown crystal, so it is confirmed that LiTaO3 was grown under congruent melting composition having optical homogeniety. Also, the optical transmittance was about 78%, which was sufficient for optical device.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1996년도 The 9th KACG Technical Annual Meeting and the 3rd Korea-Japan EMGS (Electronic Materials Growth Symposium)
• /
• pp.258-292
• /
• 1996

In the last year great interest appears to YBCO thin films preparation on different substrate materials. Preparation of epitaxial film is a very difficult problem. There are many requirements to substrate materials that must be fullfilled. Main problems are lattice mismatch (misfit) and similarity of structure. From paper [1] or follows that difference in interatomic distances and angles of substrate and film is mire important problem than similarity of structure. In this work we present interatomic distances and angle relations between substrate materials belonging to ABCO4 group (where A-Sr or Ca, B-rare earth element, C-Al or Ga) of different orientations and YBCO thin films. There are many materials used as substrates for HTsC thin films. ABCO4 group of compounds is characterized by small dielectric constants (it is necessary for microwave applications of HTsC films), absence of twins and small misfit [2]. There most interesting compounds CaNdAlO4, SrLaAlO4 and SrLaGaO4 were investigated. All these compounds are of pseudo-perovskite structure with space group 14/mmm. This structure is very similar to structure of YBCO. SLG substrate has the lowest misfit (0.3%) and dielectric constant. For preparation of then films of substrates of this group of compound plane of <100> orientation are mainly used. Good quality films of <001> orientations are obtained [3]. In this case not only a-a misfit play role, but c-3b misfit is very important too. Sometimes, for preparation of thin films substrates of <001> and <110> orientations were manufactured [3]. Different misfits for different YBCO faces have been analyzed. It has been found that the mismatching factor for (100) face is very similar to that for (001) face so there is possibility of preparation of thin films on both orientations. SrLaAlO4(SLA) and SrLaGaO4(SLG) crystals of general formula ABCO4 have been grown by the Czochralski method. The quality of SLA and SLG crystals strongly depends on axial gradient of temperature and growth and rotation rates. High quality crystals were obtained at axial gradient of temperature near crystal-melt interface lower than 50℃/cm, growth rate 1-3 mm/h and the rotation rate changing from 10-20pm[4]. Strong anisotropy in morphology of SLA and SLG single crystals grown by the Czochralski method is clearly visible. On the basics of our considerations for ABCO4 type of the tetragonal crystals there can appear {001}, {101}, and {110} faces for ionic type model [5]. Morphology of these crystals depend on ionic-covalent character of bonding and crystal growth parameters. Point defects are observed in crystals and they are reflected in color changes (colorless, yellow, green). Point defects are detected in directions perpendicular to oxide planes and are connected with instability of oxygen position in lattice. To investigate facets formations crystals were doped with Cr3+, Er3+, Pr3+, Ba2+. Chromium greater size ion which is substituted for Al3+ clearly induces faceting. There appear easy {110} faces and SLA crystals crack even then the amount of Cr is below 0.3at.% SLG single crystals are not so sensitive to the content of chromium ions. It was also found that if {110} face appears at the beginning of growth process the crystal changes its color on the plane {110} but it happens only on the shoulder part. The projection of {110} face has a great amount of oxygen positions which can be easy defected. Pure and doped SLA and SLG crystals measured by EPR in the<110> direction show more intensive lines than in other directions which allows to suggest that the amount of oxygen defects on the {110} plane is higher. In order to find the origin of colors and their relation with the crystal stability, a set of SLA and SLG crystals were investigated using optical spectroscopy. The colored samples exhibit an absorption band stretching from the UV absorption edge of the crystal, from about 240 nm to about 550 m. In the case of colorless sample, the absorption spectrum consists of a relatively weak band in the UV region. The spectral position and intensities of absorption bands of SLA are typical for imperfection similar to color centers which may be created in most of oxide crystals by UV and X-radiation. It is pointed out that crystal growth process of polycomponent oxide crystals by Czochralski method depends on the preparation of melt and its stoichiometry, orientation of seed, gradient of temperature at crystal-melt interface, parameters of growth (rotation and pulling rate) and control of red-ox atmosphere during seeding and growth (rotation and pulling rate) and control of red-ox atmosphere during seeding and growth. Growth parameters have an influence on the morphology of crystal-melt interface, type and concentration of defects.