• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.9
• /
• pp.166-173
• /
• 2000

A system for burr measurement is developed to measure the geometry of the burr formed in metal cutting or shearing operations. laser system is selected according to the required measuring accuracy and burr size. A specific program for calculating the burr geometry from measured laser data is developed. The raw data is obtained by scanning cross the burr. The height and width of burr are calculated. Due to the specific characteristic of laser peak or valley are formed in measuring sharp edges or small sharp cracks. Compensation for the peak or valley is carried out to make it possible to calculate the burr, burr geometry is measured in 3 dimension.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.107-110
• /
• 2003

The sheet metal shearing process is normally used in the precision elements such as semi-conductor components. In precision elements, burrs usually reduce the quality of machined parts and cause interference, jamming and misalignment during assembly procedures and because of their sharpness, they can be safety hazard to personnel. Furthermore, not only burrs are hard to predict and avoid, but also deburring, the process of removing burrs, is time-consuming and costly. In order to get the burr-free parts, therefore, we developed the precise burr measuring system using the laser. Using the X-Y precious table, we used vertical measuring method. Through the laser measurement system, we gain the minute analog signal, so this signal was amplified by the electric circuit. Finally, we gained the realtime burr data using A/D converter, PC. By introducing the novel laser measuring method which employing vertical measurement mechanism, we could get fast and precious burr data. Through the experiments, the accuracy of the developed system is proved. The burr height measured during the punching process can be used for automatic deburring and in-situ aligning.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.951-954
• /
• 2003

Generally, for the burrs formed in machining are irregular and very sharp in shape, it is usually very difficult to measure burr accurately. But, it is proved that precision measurement for micro burr using the conoprobe sensor by conoscopic holography method is possible. We developed 3D burr measurement system using this sensor. The system is composed of Conoscopic laser Sensor, X-Y table, controller and 3D measurement program. Some measurements using the developed system are applied to burrs formed in micro drilling and piercing.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.6
• /
• pp.81-87
• /
• 2003

Triangulation method, conoscopic holography method and interferometry method are analyzed for effective measurement of micro burr geometry, which is formed in micro drilling. To select proper sensor, the cross section of a cylinder with 0.5mm diameter is measured and the result shows that conoscopic holography method is effective for measuring highly inclined surface in cylinder. Burrs with 1.0mm and 30${\mu}{\textrm}{m}$ height are measured by three suggested methods. As a result, the conoscopic holography method is proved to be most proper in measuring burr geometry. Burr measurement system is developed, which consists of conoscopic laser sensor, X-Y table, controller and burr measurement program. Burrs can be measured automatically and the result is displayed in 3D shape

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.132-140
• /
• 2000

In conventional drilling, burr geometry can be changed according to the variation of drill geometry like point angle, rake angle. Step drilling is proposed to minimize the burr formation in drilling operation. The burr formed in first cutting can be removed in second cutting by the edge in step. The burr formed in second cutting by the edge in step can be minimized according to the change of geometry like, step angle and depth. The mechanism in step drilling is analyzed. Some step drills are applied to drilling the input shaft which is used for vehicle steering. To measure the burr formed in drilling, laser and height gage are used.

• Journal of Mechanical Science and Technology
• /
• v.19 no.4
• /
• pp.968-975
• /
• 2005

The shearing process for the sheet metal is normally used in the precision elements such as semi-conductor components. In these precision elements, the burr formation brings a bad effect on the system assembly and demands the additional de-burring process, so this imposes high cost on manufacturing. In this paper, we have developed the in-situ auto-aligning precision meso-punching system to investigate the burr formation mechanism and ultimately minimize burr. Firstly, we introduced the punch-die contact sensing method to align the punch and the die at initial state prior to the punching process. Secondly, by using the low-price semi-con­ductor laser, burr formed on the edges is measured intermittently during the punching process. We could, finally, make burr on the sheet metal uniformized and minimized by controlling of the precision X - Y table, $1\;{\mu}m$ resolution, and measuring burr height by semiconductor laser. Experimental results show the validity of our system for pursuing the burr-free punched elements.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1253-1256
• /
• 2005

An Experiment was carried out to study burr minimization in drilling on the inclined exit surface. Several different drills, exit surface angles and cutting conditions were selected to determine their influences on burr formation. In drilling operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quiet different burr formation when comparing with flat surface. Burr formation mechanisms are analyzed according to the drill geometries and cutting conditions. Several schemes for burr minimization on inclined exit surface were proposed. Burr geometry in each drill and cutting condition are measured by laser measurement system.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.560-564
• /
• 1999

Burr sensing for burr size measurement and deburring process control is one of the essential elements in an automated deburring procedure. This paper presents the implementation of capacitance sensing and acoustic emission (AE) to deburring. The first application is the "on-line" measurement of burrs using a capacitance sensor. A non-contact capacitance gauging sensor is attached to an ultra precision milling machine which was used as a positioning system. The setup is used to measure burr profiles along machined workpiece edges. The proposed scheme is shown to be accurate, easy to setup, and with minor modifications, readily applicable to automatic deburring processes. As the second example, AE signals were sampled and analyzed for the sensor feedback of a precision deburring process - laser deburring -. The results, such as the sensitivity of AE signals to burr shapes and edge detection capability show a clear correlation between physical process parameters and the AE signals. A subsequent control strategy for deburring automation is also briefly discussed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.434-438
• /
• 2003

The shearing process for the sheet metal is normally used in the precision elements such as semi-conductor components. In these precision elements, the burr formation brings a bad effect on the system assembly and demands the additional de-burring process. In this paper, we have developed the desktop-type precision punching system to investigate the burr formation mechanism and present kinematically Punch-die auto aligning methodology, for the purpose of burr unifomizing and minimizing, between the rectangular shaped punch and die. By using the scanning electron microscope, the aligned punching results are compared with the miss-aligned ones. Also, we measured the relative burr heights using the self-designed laser measuring device for insitu self aligning. Since it is hard to get the perfect, so called, burr-free edges during the shearing process, we introduced the ultrasonic do-burring machine. The de-burring operation was carried out by a novel do-burring method, the reversal flow resistance method, under different machining loads and abrasive types. The final do-burring results show the validity of our punching do-burring system pursuing the burr-free punched elements.

• International Journal of Precision Engineering and Manufacturing
• /
• v.1 no.1
• /
• pp.152-159
• /
• 2000

In piercing operation for small hole in very thin plate, micro burrs are formed. The micro burr is very difficult to remove because the thin plate is to be deformed during deburring and deteriorate accuracy. As a first step to remove the micro burrs effectively, the burr must be measured accurately as much as possible. For most micro burrs are so small as less than 10$\mu\textrm{m}$, it is very difficult to measure. Several methods are reviewed to measure the micro burr formed in piercing operation from very thin plate with thickness less than 0.1mm. Also the effective deburring methods are reviewed. Barreling ultrasonic and chemical deburring methods are performed and the results are compared.