• Journal of the Optical Society of Korea
• /
• v.4 no.2
• /
• pp.94-99
• /
• 2000

Optical monitoring using the chromatic aberration of focusing optics is applied to auto-focus control in laser welding. The spectral transmittance of thermal radiation from a weld pool through an aperture depends on the wavelength of the spectral band and on the distance of the weld pool from the focusing optics. Its dependence has been used to monitor the focus shift in laser welding by measuring the spectral band signals filtered by the aperture. The difference between pulsed and continuous laser welding is analyzed. Furthermore, the dependence of the focus shift monitoring on the weld pool size variation is optimized to monitor the focus shift independently from the laser power change at the weld pool. The performance of the auto-focus control with chromatic filtering is presented for pulsed laser welding.

• Journal of Welding and Joining
• /
• v.23 no.5
• /
• pp.55-60
• /
• 2005

A precise bonding technique, transmission laser bonding using energy transfer, for polymer micro devices is presented. The irradiated IR laser beam passes through the transparent part and absorbed on the opaque part. The absorbed energy is converted into heat and bonding takes place. In order to optimize the bonding quality, the temperature profile on the interface must be obtained. Using optical measurements of the both plates, the absorbed energy can be calculated. At the wavelength of 1100nm $87.5\%$ of incident laser energy was used for bonding process from the calculation. A heat transfer model was applied for obtaining the transient temperature profile. It was found that with the power of 29.5 mW, the interface begins to melt and bond each other in 3 sec and it is in a good agreement with experiment results. The transmission IR laser bonding has a potential in the local precise bonding in MEMS or Lab-on-a-chip applications.

• Current Optics and Photonics
• /
• v.5 no.5
• /
• pp.544-553
• /
• 2021

A 40-W 200-ns 300-kHz thulium-doped fiber laser at 2050 nm with a master oscillator power amplifier configuration was developed, for application to lithium-isotope separation. The master oscillator generated a 5.35 W continuous-wave beam, which the pulse generator then broke into 200-ns pulses at 300 kHz. Then, the laser beam was amplified by passing through a two-stage amplifier. The output power finally obtained was 42.0 W at 2050 nm, and was stable for a long time, over 2 hours. In spite of this achievement, mode instability was observed in the output beam. This can be solved in the future by using a method such as tight coiling.

• Proceedings of the Korean Society of Potoscience Conference
• /
• spring
• /
• pp.33-33
• /
• 1996

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.1
• /
• pp.58-71
• /
• 2009

The blast wave released during the initiation of energetic materials gives rise to pulse energy generation, characterized by a sudden increase of potential energy. A highly efficient energy source, sought from pulse-type lasers, may be utilized in various space propulsion and power applications. This paper introduces a scheme of utilizing the laser energy in 1) attitude control of a satellite requiring of a low thrust, 2) innovative laser-induced drug delivery, 3) implosion-based micro piston development, 4) deflecting and zapping of space debris for laser kill purpose, and 5) finally lunar detection using laser induced breakdown spectroscopy.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2017.10a
• /
• pp.235-236
• /
• 2017

• Laser Solutions
• /
• v.16 no.2
• /
• pp.1-6
• /
• 2013

Picosecond lasers are a very effective tool for micromachining metals, especially when high accuracy, high surface roughness and no heat affected zone are required. However, low productivity has been a limit to broadening the spectrum of their industrial applications. Recently it was reported that in the micromachining of copper with a 1064nm picosecond laser, there exist the optimal pulse energy and repetition rate to achieve the maximum volume ablation rate. In this paper, we used a 515nm picosecond laser, which is more efficient for micromachining copper in terms of laser energy absorption, to obtain its optimal pulse energy and repetition rate. Theoretical analysis based on the experimental data on copper ablation showed that using a 515nm picosecond laser instead of a 1064nm picosecond laser is more favorable in that the calculated threshold fluence is 75% lower and optical penetration depth is 50% deeper.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.3
• /
• pp.96-100
• /
• 2004

The Nd： YAG laser is commonly used throughout many fields such as accurate material processing, IC marking, semiconductor annealing, medical operation devices, etc., due to the fact that it has good thermal and mechanical properties and is easy to maintain. In materials processing, it is essential to vary the laser power density for specific materials. The laser power density can be mainly controlled by the current pulse width and pulse repetition rate. It is important to control the laser energy in those fields using a pulsed laser. In this paper we propose the constant-frequency current resonant half-bridge converter and monitoring of capacitor charging voltage. This laser power supply is designed and fabricated to have less switching loss, compact size, isolation with primary and secondary transformers, and detection of capacitor charging voltage. Also, the output stabilization characteristics of this Nd： YAG laser system are investigated. The test results are described as a function of laser output energy and flashlamp arc discharging constant. At the energy storage capacitor charges constant voltage, the laser output power is 2.3％ error range in 600[V].

• Korean Journal of Materials Research
• /
• v.23 no.5
• /
• pp.260-265
• /
• 2013

Silicon nanoparticle is a promising material for electronic devices, photovoltaics, and biological applications. Here, we synthesize silicon nanoparticles via $CO_2$ laser pyrolysis and study the hydrogen flow effects on the characteristics of silicon nanoparticles using high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), and UV-Vis-NIR spectrophotometry. In $CO_2$ laser pyrolysis, used to synthesize the silicon nanoparticles, the wavelength of the $CO_2$ laser matches the absorption cross section of silane. Silane absorbs the $CO_2$ laser energy at a wavelength of $10.6{\mu}m$. Therefore, the laser excites silane, dissociating it to Si radical. Finally, nucleation and growth of the Si radicals generates various silicon nanoparticle. In addition, researchers can introduce hydrogen gas into silane to control the characteristics of silicon nanoparticles. Changing the hydrogen flow rate affects the nanoparticle size and crystallinity of silicon nanoparticles. Specifically, a high hydrogen flow rate produces small silicon nanoparticles and induces low crystallinity. We attribute these characteristics to the low density of the Si precursor, high hydrogen passivation probability on the surface of the silicon nanoparticles, and low reaction temperature during the synthesis.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.162-168
• /
• 2002

Hybrid Welding means the coupling of the energy of two different energy sources in a common process zone. This paper describes prospects in laser-arc-hybrid-welding. Different kinds of lasers ($CO_2$ laser and Nd:YAG laser) and arc processes (TIG, Plasma and GMA) are considered.