• Nuclear Engineering and Technology
• /
• v.44 no.8
• /
• pp.953-960
• /
• 2012

This paper reports the irradiation effect on the deformation behavior and tensile fracture properties of A533B RPV steel. An inverse identification technique using iterative finite element (FE) simulation was used to determine those properties from tensile data for the A533B RPV steel irradiated at 65 to $100^{\circ}C$ and deformed at room temperature. FE simulation revealed that the plastic instability at yield followed by softening for higher doses was related to the occurrence of localized necking immediately after yielding. The strain-hardening rate in the equivalent true stress-true strain relationship was still positive during the necking deformation. The tensile fracture stress was less dependent on the irradiation dose, whereas the tensile fracture strain and fracture energy decreased with increasing dose level up to 0.1 dpa and then became saturated. However, the tensile fracture strain and fracture energy still remained high after high-dose irradiation, which is associated with a large amount of ductility during the necking deformation for irradiated A533B RPV steel.

• International Journal of Concrete Structures and Materials
• /
• v.18 no.3E
• /
• pp.213-219
• /
• 2006

Modified singular fracture process zone(S-FPZ) model is proposed in this paper to determine a fracture criterion for continuous crack propagation in concrete. The investigated fracture properties of the proposed fracture model are strain energy release rate at a micro-crack tip and the relationship between crack closure stress(CCS) and crack opening displacement(COD) in the FPZ. The proposed model can simulate the actual fracture energy of experimental results fairly well. The results of the experimental data analysis show that specimen geometry and loading condition did not affect the CCS-COD relation. However, the strain energy release rate is a function of not only specimen geometry but also crack extension. The strain energy release rate remained constantly at the minimum value up to the crack extension of 25 mm, and then it increased linearly to the maximum value. The maximum fracture criterion occurred at the peak load for specimens of large size. The fracture criterion remained at the maximum value after the peak load. The variation of the fracture criterion is caused by micro-cracking and micro-crack localization. The fracture criterion of strain energy release rate can simply be the size effect of concrete fracture, and it can be used to quantify the micro-cracking and micro-crack localizing behavior of concrete.

• Journal of Welding and Joining
• /
• v.28 no.2
• /
• pp.39-46
• /
• 2010

IIn this study, used is the equivalent loading method based on the inherent strain to predict the welding deformation of panel members. Equivalent loads are computed from the inherent strain distribution around weld line, and then applied for the linear finite element analysis. Thermal deformation of panel members can be, of course, carried out through the rigorous thermal elasto-plastic analysis procedure but it is not practical in applying to predicting the welding deformation of large structures such as blocks found in a ship structure from view of computing time. The present equivalent load approach has been applied to flat plate model to verify the present approach, and to several curved plate models having the curvature in the welding direction to investigate the effect of the longitudinal curvature upon the weld-induced deformation. The results are compared with those by thermal elasto-plastic analysis. As far as the present results are concerned, it can be said that the present approach shows good agreement with the results by welding experiment and the rigorous thermal elasto-plastic analysis. The present approach has been also applied to predict the welding deformation of panel block as for application illustration to practical model.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.2 no.2
• /
• pp.185-189
• /
• 2001

Wild type Bacilus thuringiensis subsp. israelensis and B. sphaericus toxins have been used separately as active in ingredients for bacterial insecticides to control mosquito larvae due to their comparable toxicity to chemical insecticides. Cry11B, recently cloned from B. thuringiensis subsp. jegathesan, shows higher toxicity against three major species of mosquito larvae than Cry11A, one of the major component of B. thuringiensis subsp. israelensis inclusion body. To determine whether the combination of cry11B and B. sphaericus binary toxins is as toxic as B. thuringiensis subsp. israelensis parental strain, cry11B and B. sphaericus binary toxins genes were co-expressed as an operon using cytlA promoters/STAB-SD hybrid expression system in B. thuringiensis subsp. israelensis acrystalliferous strain 4Q7. However, unexpectedly, B. sphaericus binary toxins were barely produced, whereas relatively large amount of Cry11B was produced. When this strain was grown in four different media, NB+G and Peptonized Milk produced more toxin proteins and spores per unit of media than GYS and G-Tris. Toxicity of this strain against fourth instar Culex quinquefasciatus was ranged from of 8.3 to 45.7 ng/ml, with NB+G culture being the highest, and GYS culture was the lowest.

• Korean Journal of Veterinary Research
• /
• v.34 no.1
• /
• pp.99-105
• /
• 1994

Clotridium bovis sp. nov, is described on the basis of 5 strains isolated from the feces of Holstein cattle. The isolate are gram-positive, motile, strict anaerobic spore forming rods. They differ from all the validly described related species of the genus Clostridium in carbohydrate fermentation pattern, G+C mol% and DNA homologies. Acid is produced from arabinose, xylose, glucose, mannose, fructose, galactose, sucrose, maltose, cellobiose, lactose, trehalose, melibiose, raffinose, inulin and salicin. Major end products in PYFG broth are large amounts of butyric acid and lactic acid, and trace amounts of acetic and succinic acids. The G+C mol% of DNA from the type strain is 26 mol%. The type strain of Clostridium bovis is Catt $66^T$ strain.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.2
• /
• pp.671-678
• /
• 2019

In this paper, the low cycle fatigue failure and ratcheting behavior, as well as their interaction of AH32 steel were experimentally investigated under uniaxial cyclic loading. The effects of mean stress, stress amplitude and stress ratio on the low cycle fatigue life and ratcheting strain were discussed. It was found that the ratcheting strain increased while the fatigue life decreased with the increase of mean stress and stress amplitude, and the increasing stress ratio would result in smaller ratcheting and larger fatigue life. Two kinds of failure modes, i.e. low cycle fatigue failure due to crack propagates and ratcheting failure due to large plastic strain will take place respectively. Based on the experimental results, considered the effect of ratcheting on fatigue life, a model with the maximum stress and ratcheting strain rate was proposed. Comparison with the experimental result showed that the new model provided a good prediction for AH32 steel.

• Korean Journal of Optics and Photonics
• /
• v.12 no.4
• /
• pp.294-299
• /
• 2001

Recently great efforts and investment have been made in order to develop a structural health monitoring technology using fiber optic sensors. Therefore, in this study, we have focused on the development of a fiber optic BOTDA (Brillouin Optical Time Domain Analysis) sensor system in order to measure strains distributed on large structures by an optical fiber. The fiber optic BOTDA sensor was constructed simply, with only two electro-optic modulators. The results of strain measurement tests of an optical fiber showed that the strain can be determined accurately from the Brillouin frequency shift measurement on the strain induced range of 10 m in the total fiber length of 4.8 kIn using 200 averaged signals. Also, the strain sensitivity of Samsung single mode fiber was 4.81 MHz/O.Ol % under the test. test.

• Elastomers and Composites
• /
• v.51 no.4
• /
• pp.308-316
• /
• 2016

The rubber materials are widely used in automobile industry due to their capability of a large amount of elastic deformation under a force. Current trend of design process requires prediction of functional properties of parts at early stage. The behavior of rubber material can be modeled using strain energy density function. In this study, five different strain energy density functions - Neo-Hookean model, Reduced Polynomial $2^{nd}$ model, Ogden $3^{rd}$ model, Arruda Boyce model and Van der Waals model - were used to estimate the behavior of carbon black added natural rubber under uniaxial load. Two kinds of tests - uniaxial tension test and biaxial tension test - were performed and used to correlate the coefficients of the strain energy density function. Numerical simulations were carried out using finite element analysis and compared with experimental results. Simulation revealed that Ogden $3^{rd}$ model predicted the behavior of carbon added natural rubber under uniaxial load regardless of experimental data selection for coefficient correlation. However, Reduced Polynomial $2^{nd}$, Ogden $3^{rd}$, and Van der Waals with uniaxial tension test and biaxial tension test data selected for coefficient correlation showed close estimation of behavior of biaxial tension test. Reduced Polynomial $2^{nd}$ model predicted the behavior of biaxial tension test most closely.

• Advanced Composite Materials
• /
• v.17 no.3
• /
• pp.191-214
• /
• 2008

Polypropylene/layered silicate nanocomposites containing maleic anhydride grafted polypropylene were prepared by melt compounding and their rheological behavior was investigated in shear flow. Transient and steady shear flows were simulated numerically by using the K-BKZ integral constitutive equation along with experimentally determined damping functions under dynamic oscillatory and step strain shear flows. Nonlinear shear responses were predicted with the K-BKZ constitutive equation using two different damping functions such as the Wagner and PSM models. It was observed that PP-g-MAH compatibilized PP/layered silicate nanocomposites have stronger and earlier shear thinning and higher steady shear viscosity than pure PP resin or uncompatibilized nanocomposites at low shear rate regions. Strong damping behavior of the PP/layered silicate nanocomposite was predicted under large step shear strain and considered as a result of the strain-induced orientation of the organoclay in the shear flow. Steady shear viscosity of the pure PP and uncompatibilized nanocomposite predicted by the K-BKZ model was in good agreement with the experimental results at all shear rate regions. However, the model was inadequate to predict the steady shear viscosity of PP-g-MAH compatibilized nanocomposites quantitatively because the K-BKZ model overestimates strain-softening damping behavior for PP/layered silicate nanocomposites.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.3
• /
• pp.188-192
• /
• 2012

In this study, a carbon nanotube (CNT) flexible strain sensor was fabricated with CNT based epoxy and rubber composites for tactile sensing. The flexible strain sensor can be fabricated as a long fibrous sensor and it also may be able to measure large deformation and contact information on a structure. The long and flexible sensor can be considered to be a continuous sensor like a dendrite of a neuron in the human body and we named the sensor as a biomimetic artificial neuron. For the application of the neuron in biomimetic engineering, an ANMS (Artificial Neuron Matrix System) was developed by means of the array of the neurons with a signal processing system. Moreover, a strain positioning algorithm was also developed to find localized tactile information of the ANMS with Labview for the application of an artificial e-skin.