• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.351-356
• /
• 1999

An elasto-plastic constitutive model was Proposed, in which the behavior at small-to-large strain level can be modeled. From a mathematical approach it was proved that the model includes the previous successful models. The experimental results of a series of resonant column tests, torsional shear tests and triaxial tests were verified and as a result the proposed model could predict small-to-large strain behavior more consistently and accurately than the hyperbolic model and the Ramberg-Osgood model for a weathered granitic soil.

• 한국지반공학회논문집
• /
• 제16권1호
• /
• pp.65-73
• /
• 2000

본 연구에서는 미소변형률에서 대변형률까지의 거동을 모델할 수 있는 탄소성 구성모델을 개발하였다. 제안된 구성모델은 일반 등방경화규칙에 근거한 비등방 경화규칙과 전응력 개념을 토대로 개발하였다. 그리고 제안된 구성관계가 기존의 대표적 구성모델을 포함하고 있음을 수학적으로 입증하였다. 국내 화강풍화토에 대한 공진주시험, 비틂전단시험, 삼축시험 등 일련의 실내시험 결과를 이용하여 검증한 결과, 쌍곡선 모델 및 Ramberg-Osgood모델과 비교하여 제안된 모델은 미소변형률에서 대변형률까지의 거동을 더욱 일관되고 정확하게 모델할 수 있다. 또한 비틂전단시험 결과와의 비교에서는, 미소변형률 조건에서 나타나는 비선형성을 적합하게 예측할 수 있었다.

• 농업과학연구
• /
• 제37권3호
• /
• pp.491-499
• /
• 2010

This study was carried out to investigate the consolidation characteristics of the remolded clay by the oedometer and the constant rate of strain(CRS) consolidation tests. As the rate of strain increases, the settlement rapidly decreased. As the ratio of the sand in the specimen increases, its effect on the rate of strain to the settlement was reduced. As the effective stress increased, the void ratio decreased, while the rate of strain increased, it did not show a clear variation. The reduction of the void ratio was shown to be less than the oedometer test. The coefficient of vertical consolidation with effective stress showed very large variation around preconsolidation stress, but the rate of strain did not provide significant effects. The rate of strain with effective stress gradually decreased at all tests and mixed ratio of sand. The rate of strain at the constant rate of strain tests showed smaller than in the oedometer test. The coefficient of consolidation at the constant rate of strain tests showed much more increase than in the oedometer test. The ratio of the vertical coefficient of consolidation by the odometer and the constant rate of strain tests showed a large difference according to various tests method and mixing ratio. Therefore, it is recommended that careful attention should be paid to designing the soft ground improvement.

• 한국항공우주학회지
• /
• 제44권1호
• /
• pp.1-11
• /
• 2016

큰 가로세로비를 가지는 유연날개의 변형정보는 구조 건전성 평가를 위한 실시간 모니터링에 필요하다. 비행 중인 날개 구조 대변형은 날개 외피의 변형률과 곡률의 관계식을 기반으로 한 비선형 변위 예측 알고리즘을 통해 예측될 수 있다. 그러나 동체에 고정된 날개의 기하학적인 형상으로 인하여 고정단 부근에서의 변형률 분포는 복잡한 양상을 나타내며, 변형률 센서가 부착된 센싱라인의 코드방향 위치에 따라 변위가 다르게 예측될 수 있다. 본 논문에서는 스팬방향 변형률의 보정을 통하여 변형률 센싱라인의 코드방향 위치에 관계없이 예측변위의 정확도를 향상시키는 연구를 수행하였다. 변형률 보정을 위하여 스팬방향 및 코드방향 변형률의 비, 재료의 포아송비, 보와 평판 모델의 변형률 비를 이용하였다. 보정된 변형률을 이용하여 예측한 변위는 해석변위와 잘 일치하였으며, 이를 실험을 통하여 검증하였다.

• 한국압력기기공학회 논문집
• /
• 제14권2호
• /
• pp.24-31
• /
• 2018

In this paper, specimen tests with simulated large seismic conditions have been carried out to investigate damage characteristics such as structural deformation and crack initiation under seismic loading. The mechanical behavior of the specimens is predicted by numerical simulations and the strain-based damage evaluations are performed. Finite element analyses of the specimens under the simulated seismic loading at room and operating temperatures were carried out for low alloy steel and stainless steel materials. Peak strain amplitude, cumulative fatigue damage and cumulative strain limit damage are calculated considering the nature of cyclic loading. In all cases, the allowable damage criteria are exceeded at the time of observing cracks visually in the tests. Therefore, it is confirmed that the material behavior due to the large seismic loads can be predicted by the numerical method and the structural damage of the materials can be evaluated conservatively based on the strain criteria.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4030-4048
• /
• 2022

In this study, road transportation tests were conducted with surrogate fuel assemblies under normal conditions of transport to evaluate the vibration and shock load characteristics of spent nuclear fuel (SNF). The overall test data analysis was conducted based on the measured acceleration and strain data obtained from the speed bump, lane-change, deceleration, obstacle avoidance, and circular tests. Furthermore, representative shock response spectrums and power spectral densities of each test mode were acquired. Amplification or attenuation characteristics were investigated according to the load transfer path. The load attenuated significantly as it transferred from the trailer to the cask. By contrast, the load amplified as it transferred from the cask to the surrogate SNF assembly. The fuel loading location on the cask disk assembly did not exhibit a significant influence on the strain measured from the fuel rods. The principal strain was in the vertical direction, and relatively large strain values were obtained in spans with large spacing between spacer grids. The influence of the lateral location of fuel rods was also investigated. The fuel rods located at the side exhibited relatively large strain values than those located at the center. Based on the strain data obtained from the test results, a hypothetical road transportation scenario was established. A fatigue evaluation of the SNF rod was performed based on this scenario. The evaluation results indicate that no fatigue damage occurred on the fuel rods.

• 한국농공학회논문집
• /
• 제48권5호
• /
• pp.63-71
• /
• 2006

In the present study, the dynamic deformation characteristics of clay, including the effect of loading rate in large strain ranges, were examined by performing undrained cyclic triaxial test. The test results showed that the loading rate to failure decreased with increasing loading amplitude and decreasing loading frequency. While the stress-strain relationships was not affected by loading frequency, excess pore pressure was affected significantly with the change in loading frequency. The change for 0.1 Hz was larger for than that of 0.01 Hz, resulting in inclined effective stress paths. Furthermore, the lower the frequency was, the higher the excess pore pressure was in the first loading.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.139-146
• /
• 2001

Undrained triaxial tests were peformed for a weathered soil, which includes local measurement using LVDT The behavior from small In large strain conditions could be evaluated consistently through a triaxial test, The stress-strain relationship of undisturbed samples were compared with the disturbed and the shear moduli in the small strain level had the almost same values. Especially the shear moduli were mostly affected by the initial condition of water contents. An anisotropic hardening model based on the total stress concept could predict the stress-strain relationship accurately, which makes it possible to analyze the geotechnical problem reasonably for the weathered soil.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.193-194
• /
• 2010

• Journal of Welding and Joining
• /
• 제18권5호
• /
• pp.84-89
• /
• 2000

Friction welding of titanium and aluminium is numerically modeled by the axisymmetric thermal elastic-plastic analysis. In titanium/aluminium friction welding, heat transfers into the titanium substrate to a distance of z=10(mm) on the side of the bondline and into the whole region of the aluminium substrate having the large thermal conductivity. Adjacent to the bondline, $^{\sigma}r\;and\;^{\sigma\theta}$ are tensile in the substrate whose thermal shrinkage is large, and are compressive in the substrate whose thermal shrinkage is small. $\sigma_z$ along the radial direction is large tensile at the periphery of the component. Plastic strain occurs only close to the bondline in the aluminium substrate. In the components of plastic strain, $\varepsilon^p_r\;and\;\varepsilon^p_{\theta}$ have positive values and $\varepsilon^p_r$ has large negative value. However, $\varepsilon^p_r$ is produced not because of the severity of the mechanical restraint condition, but on purpose to satisfy the condition of the volume constant. A plastic work is proposed as a measure to evaluate the mechanical severity. The plastic work is larger in the aluminium substrate than that in the titanium substrate. The mechanical condition is severer in the aluminium substrate.