• Journal of Korean Society of Forest Science
• /
• v.113 no.3
• /
• pp.308-318
• /
• 2024

Forest fuel management plays a crucial role in the proper management of frequent and large-scale forest fires worldwide. This study evaluated the impact of fuel management on reducing forest fire risk by through surface fire behavior through laboratory experiments and simulations using the Wildland Fire Dynamics Simulator. For Pinus densiflora litter, fuel conditions were established based on field surveys in Goseong-gun, Gangwon-do, focusing on control, 20% thinning, and 40% thinning sites. Results indicated that visible flame height, vertical temperature distribution, and maximum heat release rate tended to decrease with higher thinning intensity, implying a lower forest fire risk. Overall, the WFDS simulations produced higher values compared to the laboratory experiments, but the trends were similar. The results of this study can serve as fundamental data for evaluating forest fire risk based on thinning intensity and establishing a research foundation for fire prevention.

• The Journal of the Acoustical Society of Korea
• /
• v.43 no.5
• /
• pp.557-569
• /
• 2024

Recently, the operating speed of pressure devices is increased for high performance. It lead to the increase of flow rate. Consequently, the results in the high relative contribution of flow borne noise to the noise from pipe. Analyzing the characteristics of flow-borne noise is essential for evaluating noise performance during the design stage of the piping system. Therefore, in this paper, the noise generation mechanism and transfer characteristic was numerically investigated. The wall pressure induced by the fluid moving through the orifice was predicted using the compressible Large Eddy Simulation (LES). The Wavenumber-Frequency Analysis (WFA) was employed to decompose the wall pressure into incompressible and compressible component, which are to cause Fluid Induced Vibration (FIV) and Acoustic Induced Vibration (AIV). The propagation and contribution characteristics were analyzed using the separated incompressible and compressible wall pressure components. Additionally, the correlation between these pressure components and the internal flow within the piping was investigated through flow field analysis, which elucidated the mechanisms and propagation characteristics of flow-induced noise. From these results, it was confirmed that the contribution of the incompressible wall pressure component was high near the noise source and that the contribution of the compressible wall pressure component increased as it propagated long distances upstream and downstream direction of the noise source.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.13 no.1
• /
• pp.89-100
• /
• 2010

The aim of this study is to produce land cover maps using satellite imagery with various degrees of high resolution and then compare the accuracy of the image types and categories. For the land cover map produced on a small-scale classification the estuary area around the Nakdong river, including an urban area, farming land and waters, was selected. The images were classified by analyzing the aerial photos taken from KOMPSAT2, Quickbird and IKONOS satellites, which all have a resolution of over 1m to the naked eye. Once all of the land cover maps with different images and land cover categories had been produced they were compared to each other. Results show that image accuracy from the aerial photos and Quickbird was relatively higher than with KOMPSAT2 and IKONOS. The agreement ratio for the large-scale classification across the classification methods ranged between 0.934 and 0.956 for most cases. The Kappa value ranged between 0.905 and 0.937; the agreement ratio for the middle-scale classification was 0.888~0.913 and the Kappa value was 0.872~0.901. The agreement ratio for the small-scale classification was 0.833~0.901 and the Kappa value was 0.813~0.888. In addition, in terms of the degree of confusion occurrence across the images, there was confusion on the urbanized arid areas and empty land in the large-scale classification. For the middle-scale classification, the confusion mainly occurred on the rice paddies, fields, house cultivating area and artificial grassland. For the small-scale classification, confusion mainly occurred on natural green fields, cultivating land with facilities, tideland and the surface of the sea. The findings of this study indicate that the classification of the high resolution images with the naked eye showed an agreement ratio of over 80%, which means that it can be used in practice. The findings also suggest that the use of higher resolution images can lead to increased accuracy in classification, indicating that the time when the images are taken is important in producing land cover maps.

• Journal of Life Science
• /
• v.26 no.3
• /
• pp.282-288
• /
• 2016

Protein-protein interactions regulate the subcellular localization and function of receptors, enzymes, and cytoskeletal proteins. Proteins containing the postsynaptic density-95/disks large/zonula occludens-1 (PDZ) domain have potential to act as scaffolding proteins and play a pivotal role in various processes, such as synaptic plasticity, neural guidance, and development, as well as in the pathophysiology of many diseases. Multi-PDZ domain protein 1 (MUPP1), which has 13 PDZ domains, has a scaffolding function in the clustering of surface receptors, organization of signaling complexes, and coordination of cytoskeletal dynamics. However, the cellular function of MUPP1 has not been fully elucidated. In the present study, a yeast two-hybrid system was used to identify proteins that interacted with the N-terminal PDZ domain of MUPP1. The results revealed an interaction between MUPP1 and Wdpcp (formerly known as Fritz). Wdpcp was identified as a planar cell polarity (PCP) effector, which is known to have a role in collective cell migration and cilia formation. Wdpcp bound to the PDZ1 domain but not to other PDZ domains of MUPP1. The C-terminal end of Wdpcp was essential for the interaction with MUPP1 in the yeast two-hybrid assay. This interaction was further confirmed in a glutathione S-transferase (GST) pull-down assay. When coexpressed in HEK-293T cells, Wdpcp was coimmunoprecipitated with MUPP1. In addition, MUPP1 colocalized with Wdpcp at the same subcellular region in cells. Collectively, these results suggest that the MUPP1-Wdpcp interaction could modulate actin cytoskeleton dynamics and polarized cell migration.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.54 no.2
• /
• pp.146-156
• /
• 2018

Acoustic surveys were conducted in the seas surround the South Korea (South Sea A, South Sea B (waters around the Jeju Island), West Sea and East Sea) in spring and autumn in 2016. First, the vertical and horizontal distributions of fisheries resources animals were examined. In most cases vertical acoustic biomass was high in surface water and mid-water layers other than South Sea A in autumn and West Sea. The highest vertical acoustic biomass showed at the depth of 70-80 m in the South Sea A in spring ($274.4m^2/nmi^2$) and the lowest one was 10-20 m in the West Sea in autumn ($0.4m^2/nmi^2$). With regard to the horizontal distributions of fisheries resources animals, in the South Sea A, the acoustic biomass was high in eastern and central part of the South Sea and the northeast of Jeju Island ($505.4-4099.1m^2/nmi^2$) in spring while it was high in eastern South Sea and the coastal water of Yeosu in autumn ($1046.9-2958.3m^2/nmi^2$). In the South Sea B, the acoustic biomass was occurred high in the southern and western seas of Jeju Island in spring ($201.0-1444.9m^2/nmi^2$) and in the southern of Jeju Island in autumn ($203.7-1440.9m^2/nmi^2$). On the other hand, the West Sea showed very low acoustic biomass in spring (average NASC of $1.1m^2/nmi^2$), yet high acoustic biomass in the vicinity of 37 N in autumn ($562.6-3764.2m^2/nmi^2$). The East Sea had high acoustic biomass in the coastal seas of Busan, Ulsan and Pohang in spring ($258.7{\sim}976.4m^2/nmi^2$) and of Goseong, Gangneung, Donghae, Pohang and Busan in autumn ($267.3-1196.3m^2/nmi^2$). During survey periods, fish schools were observed only in the South Sea A and the East Sea in spring and the West Sea in autumn. Fish schools in the South Sea A in spring were small size ($333.2{\pm}763.2m^2$) but had a strong $S_V$ ($-49.5{\pm}5.3dB$). In the East Sea, fish schools in spring had low $S_V$ ($-60.5{\pm}14.5dB$) yet had large sizes ($537.9{\pm}1111.5m^2$) and were distributed in the deep water depth ($83.5{\pm}33.5m$). Fish schools in the West Sea in autumn had strong $S_V$ ($-49.6{\pm}7.4dB$) and large sizes ($507.1{\pm}941.8m^2$). It was the first time for three seas surrounded South Korea to be conducted by acoustic surveys to understand the distribution and aggregation characteristics of fisheries resources animals. The results of this study would be beneficially used for planning a future survey combined acoustic method and mid-water trawling, particularly deciding a survey location, a time period, and a targeting water depth.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.3
• /
• pp.543-560
• /
• 2018

With the increased development in downtown underground space facilities that vertically cross under a railway at a shallow depth, the demand for non-open cut method is increasing. However, most construction sites still adopt the pipe roof method, where medium and large diameter steel pipes are pressed in to form a roof, enabling excavation of the inside space. Among the many factors that influence the loosening region and loads that occur while pressing in steel pipes, the size of the pipe has the largest impact, and this factor may correspond to the magnitude of load applied to the underground structure inside the steel pipe roof. The super equilibrium method (SEM) has been developed to minimize ground disturbance and loosening load, and uses small diameter pipes of approximately 114 mm instead of conventional medium and large diameter pipes. This small diameter steel pipe is called an SEM pile. After SEM piles are pressed in and the grouting reinforcement is constructed, a crossing structure is pressed in by using a hydraulic jack without ground subsidence or heaving. The SEM pile, which plays the role of timbering, is a fore-poling pile of approximately 5 m length that prevents ground collapse and supports surface load during excavation of toe part. The loosening region should be adequately calculated to estimate the spacing and construction length of the piles and stiffness of members. In this paper, we conducted a comparative analysis of calculations of loosening load that occurs during the press-in of SEM pile to obtain an optimal design of SEM. We analyzed the influence of factors in main theoretical and empirical formulas applied for calculating loosening regions, and carried out FEM analysis to see an appropriate loosening load to the SEM pile. In order to estimate the soil loosening caused by actual SEM-pile indentation and excavation, a steel pipe indentation reduction model test was conducted. Soil subsidence and soil loosening were investigated quantitatively according to soil/steel pipe (H/D).

• The Korean Journal of Quaternary Research
• /
• v.13 no.1
• /
• pp.35-43
• /
• 1999

Goryeri archaeological site is located in the upstream valley of the Danjang River. The basement rocks of the area are composed of the Cretaceous to Palaeogene biotite granite (KbGr), acidic dyke (Kad), Milyang Andesite (Kma) and Jyunggagsan Formation. Among them Milyang Andesite and Jyunggagsan Formation are prevailed in archaeological site and they are composed of reddish brown tuffaceous shale, sandstone and conglomerate, with intercalations of acidic tuffs and lapilli tuffs. The purpose of this research is not only to compare REE pattern of the soil-sedimentary deposits with those of surrounding rocks, but also to identify vitric tephra in the soil-sedimentary deposits derived from the andesite, acidic tuff and lapilii tuff, in order to illucidate the provenance of the vitric tephra. The rare earth element(REE) of the soils and sedimentary deposits results in the same REE pattern with those analyzed from the surrounding basement rocks. This indicates that the soils and sedimentary deposits are originated from the surrounding basement rocks, most probably from the andesite and lapilli tuff. In addition, vitric tephra were identified both in the Quaternary in-situ weathered soils and sedimentary deposits (PMU-13 and PMU-17), and in the weathered surrounding lapilli tuff. These vitric tephra are considered to be different from those of Japanese AT(Aira Tanzawa) -tephra. The latter is predominant with clean, platty, bubble-walled and Y-shaped vitrics, while the former is conspicuous with those shapes of large and diverse size and devitrified, as well as having secondarily bubbled-surfaces reflecting surface weathering. The size of vitric fragments in the Goryeri site is about 300${\mu}{\textrm}{m}$ and large in size in compasion to 150${\mu}{\textrm}{m}$ of Japanese AT-Tephra. The interim results of the research are contradictary to the explanations based on a series of AT-tephra researches carried by Japanese scholar. In short, the vitric materials of the Goryeri archaeological site are most probably originated from the weathering products of the surrounding basement rocks, and are different from the AT-tephra in their size, shape and devitrification properties. Thus it is highly recommended to have a further comprehensive research which is more emphasized the magmatic genesis of these vitric tephra in addition to the external shape and morphology.

• Analytical Science and Technology
• /
• v.23 no.1
• /
• pp.1-14
• /
• 2010

It is of importance that all countries in worldwide, including EU and China, have adopted the Restrictions on the use of certain Hazardous Substances (RoHS) for all electronics. IEC62321 document, which was published by the International Electronics Committee (IEC) can have conflicts with the standards in the market. On the contrary Publicly Accessible Specification (PAS) for sampling published by IEC TC111 can be adopted for complementary application. In this work, we tried to find a route to disassemble and disjoint cellular phone sample, based on PAS and compare the screening methods available in the market. For this work, the cellular phone produced in 2001, before the regulation was born, was chosen for better detection. Although X-ray Fluorescence (XRF) showed excellent performance for screening, fast and easy handling, it can give information on the surface, not the bulk, and have some limitations due to significant matrix interference and lack of variety of standards for quantification. It means that screening with XRF sometimes requires supplementary tool. There are several techniques available in the market of analytical instruments. Laser ablation (LA) ICP-MS, energy dispersive (ED) XRF and scanning electron microscope (SEM)-energy dispersive X-ray (EDX) were demonstrated for screening a cellular phone. For quantitative determination, graphite furnace atomic absorption spectrometry (GF-AAS) was employed. Experimental results for Pb in a battery showed large difference in analytical results in between XRF and GF-AAS, i.e., 0.92% and 5.67%, respectively. In addition, the standard deviation of XRF was extremely large in the range of 23-168%, compared with that in the range of 1.9-92.3% for LA-ICP-MS. In conclusion, GF-AAS was required for quantitative analysis although EDX was used for screening. In this work, it was proved that LA-ICP-MS can be used as a screening method for fast analysis to determine hazardous elements in electrical products.

• Journal of the Korean earth science society
• /
• v.33 no.3
• /
• pp.259-268
• /
• 2012

To investigate the fluctuation of marine aerosol number concentration at each different size with vertical winds in ocean area, aerosol particles and vertical wind components were measured in the Ieodo Ocean Research Station, which is located to 419 km southwest of Marado, the southernmost island of Korea, from 8 to 22 June 2009. The Laser Particle Counter (LPC) and ultrasonic anemometer were used to measure the number of aerosol particles and vertical wind speed. Surface weather chart, NCEP/NCAR reanalysis data and sounding data were used to analyze the synoptic condition. The distribution of aerosol number concentration had a large fluctuation of bigger particles more than 1.0 ${\mu}m$ in diameter by vertical wind speed during precipitation. The aerosol particles larger than 1.0 ${\mu}m$ in diameter increased as the wind changed from downward to upward during precipitation. The aerosol number concentration of bigger size than 1.0 ${\mu}m$ in diameter increased about 5 times when vertical velocity was about 0.4 $ms^{-1}$. In addition, the accumulation and coarse mode aerosol number concentration decreased about 45% and 92%, respectively compared to concentrations during precipitation period. It is considered that vertical wind plays an important role for the increasing of coarse mode aerosol number concentration compared to the large aerosol particles sufficiently removed by the scavenging effect of horizontal winds. Therefore, the upward vertical winds highly contribute to the formation and increase in aerosol number concentration below oceanic boundary layer.

• Journal of Food Hygiene and Safety
• /
• v.23 no.4
• /
• pp.304-308
• /
• 2008

We investigated temperature management for refrigerated foods in large discount markets, department stores, and convenience stores. Eleven stores in the Seoul area were used to examine temperature maintenance for frozen and refrigerated foods, including soybean curds (tofu), fish surimi, mook, wet noodles, kimbab, and salads. The surficial and central temperatures of foods in a refrigerator and a freezer were examined. While the difference between the highest ($7.5^{\circ}C$) and the lowest ($6.4^{\circ}C$) temperature spaces in a refrigerator was $1.1^{\circ}C$, the corresponding difference between the highest ($8.9^{\circ}C$) and lowest ($7.5^{\circ}C$) food surface temperatures was $1.4^{\circ}C$. The average temperatures of both chilled food surfaces and refrigerator spaces were $7^{\circ}C$ (max. $22.9^{\circ}C$) and 8.2 degrees C (in. $-0.4^{\circ}C$), respectively. The temperatures of chilled food surfaces were $6.1{\times}10.6^{\circ}C$ for soybean curds, $6{\sim}12.3^{\circ}C$ for fish paste, $2.3{\times}18.2^{\circ}C$ for kimbab, $4.6{\times}12.2^{\circ}C$ for salads, $3.4{\times}12.6^{\circ}C$ for wet noodles, and $7.1{\times}19^{\circ}C$ for mook. Our results indicate that chilled foods require careful management for storage at temperatures below $10^{\circ}C$ with careful recording of the warmest area of the refrigerator.