• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.5
• /
• pp.60-67
• /
• 2021

According to the 「Guidelines of Structural Design for Piloti Building」 of the Ministry of Land, Infrastructure and Transport (2018), the natural period of middle and low rise building of upper-walled lower frame type, such as the domestic multiplex house in piloti style, is suggested for safety to apply the existing code formula of the wall structure. However, the current code formula of the wall structure was provided based on actual measurement of high-rise wall-type structures that mainly exhibit bending behavior. So it is considered that it is not suitable for a piloti-type house with four stories or less, where the wall behaves in shear. See also Park et al. (2000) confirmed that the effect of the lower frame part is greater than that of the upper wall part in the natural period of complex structures with 10 or more floors through analytical studies. Therefore, in this study, in order to examine the effect of the lower frame on the natural period of the middle and low-rise piloti structure, the estimation of natural period by the finite element analysis, approximation formula and ccurrent code formula was performed for the target structures with the shear and flexural stiffness of the upper wall and the shear stiffness of the lower frame as variables. As result, it was found that the change in the shear stiffness of the lower frame had a greater effect on the natural period of the whole building than the change in the bending or shear stiffness of the upper wall.

• Journal of the Korean Institute of Gas
• /
• v.25 no.3
• /
• pp.27-38
• /
• 2021

We devised the system to automatically shutdown the boiler and to fundamentally block the harmful gases, including carbon monoxide, into the indoor when the exhaust system swerves: (1) The discharge pressure of the exhaust gas decreases when the exhaust pipe is disconnected. The monitoring system of the exhaust pipe is implemented by measuring the output voltage of APS(Air Pressure Sensor) installed to control the amount of combustion air. (2) The operating software was modified so that when the system recognizes the fault condition of a flue pipe, the boiler control unit displays the fault status on the indoor regulator while shutting down the boiler. In accordance with the ventilation facility standards in the "Rules for Building Equipment Standards" by the Ministry of Land, Infrastructure and Transport, experiments were conducted to ventilate indoor air. When carbon monoxide leaked in worst-case scenario, it was possible to prevent poisoning accidents. However, since 2013, the number of indoor air exchange times has been mitigated from 0.7 to 0.5 times per hour. We observed the concentration exceeding TWA 30 ppm occasionally and thus recommend to reinforce this criterion. In conclusion, if the flue pipe fault detection and the indoor air ventilation system are introduced, carbon monoxide poisoning accidents are expected to decrease significantly. Also when the manufacturing and inspection steps, the correct installation and repair are supplemented with the user's attention in missing flue, it will be served to prevent human casualties from carbon monoxide poisoning.

• Korea Real Estate Review
• /
• v.28 no.1
• /
• pp.23-37
• /
• 2018

The genetic algorithm (GA) and branch and bound (B&B) methods are the useful methods of searching the optimal project combination (combinatorial optimization) to maximize the project effect considering the budget constraint and the balance of regional development with regard to the Urban Regeneration New Deal policy, the core real estate policy of the Moon Jae-in government. The Ministry of Land, Infrastructure, and Transport (MOLIT) will choose 13 central-city-area-type projects, 2 economic-base-type projects, and 10 public-company-proposal-type projects among the numerous projects from 16 local governments while each government can apply only 4 projects, respectively, for the 2017 Urban Regeneration New Deal project. If MOLIT selects only those projects with a project effect maximization purpose, there will be unselected regions, which will harm the balance of regional development. For this reason, an optimization model is proposed herein, and a combinatorial optimization method using the GA and B&B methods should be sought to satisfy the various constraints with the object function. Going forward, it is expected that both these methods will present rational decision-making criteria if the central government allocates a special-purpose-limited budget to many local governments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.773-784
• /
• 2019

With the recent development of 4th industrial revolution technology, BIM information systems are spreading to civil engineering fields as a link to this technology. Accordingly, the Land, Infrastructure and Transport Ministry is announcing a technical policy to introduce the BIM information system into the construction sector from 2020. Usually, SOC-related facilities are complex, making it difficult to implement BIM without a standards framework. To overcome these problems, it is urgent to develop a BIM standard classification system. In this study, the BIM property classification system was developed to link the previously developed object classification system by analyzing domestic and foreign prior studies and working standards. This includes property information of businesses, facilities, parts of facilities and components that correspond to the level of object composition in the road and river sectors. It also suggested ways to apply expansion to various SOC areas and to organize spatial information by facility. The results of this study were applied to road facilities to verify the possibility of information building. The development of the BIM Standards Classification System through this R&D will contribute to the development of construction IT by providing conditions for convenient modeling and information system.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.1
• /
• pp.77-85
• /
• 2019

Biogasification is a technology that uses organic wastes to reproduce as environmental fuels containing methane gas. Biogasification has attracted worldwide attention because it can produce renewable-energy and stable land treatment with prohibit from landfilling and ocean dumping of organic waste. Biomethane is produced by refining biogas. It is injected into natural gas pipeline or used transportation fuel such as cars and buses. 90 bio-gasification facilities are operating in 2016, and methane gas production is very low due to it is limited to organic wastes such as food waste, animal manure, and sewage sludge. There are seven domestic biomethane manufacturing facilities, and the use of high value-added such as transport fuels and city-gas through upgrading biogas should be expanded. On the other hand, the rapid biogasification of organic wastes in domestic resulted in frequent breakdowns of facilities and low efficiency problems. Therefore, the problem is improving as technical guidance, design and operational technical guidance is developed and field experience is accumulated. However, while improvements in biogas production are being made, there is a problem with low utilization. In this study, the problems of biomethane manufacturing facilities were identified in order to optimize the production and utilization of biogas from organic waste resources. Also, in order to present the design and operation guideline of the gas pretreatment and the upgrading process, we will investigate precision monitoring, energy balance and economic analysis and solutions for on-site problems by facility.

• Korean Journal of Construction Engineering and Management
• /
• v.20 no.1
• /
• pp.52-61
• /
• 2019

On 30 June, 2017, the Ministry of Land, Infrastructure, and Transport announced the minimum size of parking section will be expanded in parking lots. The expansion of parking section could lead to increase in apartment prices because of increase in total area of the parking lots. It is necessary to adjust the column spacing and number in the parking lots and to apply the 8-Bay long-span parking module with good parking efficiency. According to the study, the construction cost of the 6-Bay module and 8-Bay module was almost the same. But The 8-Bay module was more economical than the 6-Bay module because of the reduction in total area of 8-Bay multi-moduel. The Result of construction cost of 8-Bay modules, Removal Deck-plate RC system was most economical. While the construction cost of PC system was higher due to increase in volume of the member, it would ensure sufficient economy by reducing the girder height to apply a pre-stress method. Also, the construction cost of hollow slab system was the highest. But it could be used as the underground parking lots for apartment, because it had the lowest cost per square meter. This Study has a academic significance by proving the applicability of the 8-Bay Module to underground parking lot of apartment. And it is expected that this study will be used as basic data to derive optimal construction method that applies 8-Bay Module.

• Korean Journal of Construction Engineering and Management
• /
• v.20 no.2
• /
• pp.105-112
• /
• 2019

As the Construction Technology Promotion Act was revised in 2015, the term of Supervision was removed and Construction Management was included instead. The consideration of Construction Management shall be based on the cost plus fee method specified in the Criteria for the Cost of Construction Technology Services of the Ministry of Land, Infrastructure and Transport. Nevertheless, it is based on the construction cost ratio in accordance with the Economy and Finance Ministry's Detailed Guidelines for Preparing the 2018 Budget Plan and Fund Management Plan (Manual for Business Type and Item). As a result, it has been expected that Construction Management consideration will be calculated according to a single government standard and that the Criteria will be applied reasonably. In addition, although the change in the Labor Standard Act has a significant effect on the working environment of the construction site, the nature of the construction site is not considered in this Act. Based on these problems, the study suggested that the government should apply a single standard after consultation with the relevant agencies when calculating the consideration for Construction management, that the scope of the Criteria for the Cost of Construction Technology Services should be clear, that the amount of input by the Construction Manager should be considered for the capability of engineers and the number of working days, and that construction characteristics should be considered when determining the number of working days and hours.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.22 no.3
• /
• pp.120-132
• /
• 2019

As a key infrastructure for positioning autonomous vehicles, HD maps are making efforts to equip autonomous vehicles and connect them with services worldwide. Global companies like Here and TomTom have contracted an agreement with three German automobile companies(BMW, Audi, Daimler) by establishing systems including from the production of HD maps to loading autonomous vehicles. Japan has organized a DMP(Dynamic Map Platform) by collaborating public and private section and performing establishment of HD map on private section-oriented. Korean companies related with autonomous vehicles are also cooperating with various companies such as vehicles, sensors and maps. But public and private sections are establishing HD maps respectively. Accordingly, Ministry of Land, Infrastructure and Transport implemented and signed memorandum for private and public cooperation in April 2019, Joint establishment council of HD map has launched in August 2019. This study performed domestic and foreign trend analysis about HD map and interviewed to related companies. And analyzed solutions for interactive cooperation of private and public section in HD map industry, purposed step-by-step strategy for operation and operation plan for joint establishment council of HD map.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.22 no.3
• /
• pp.146-154
• /
• 2019

Recently, a system has been developed and applied to establish and utilize HD maps through R&D. The biggest problem, however, is the lack of a proper HD map update system, which requires the development and adoption of such a system as soon as possible. In addition, in the case of updating HD maps for automated driving, integrity and accuracy of maps are required for safe driving, so an test of these technologies and data quality is required. In April 2018, the Ministry of Land, Infrastructure and Transport implemented a project to 'Develop Technology to Demonstrate and Share the Instant Road Change Detection and Update Technology for automated driving. This paper analyzed the technology for updating map based on the investigation and analysis of relevant technology trends for the development of integrated demonstration and sharing technology of road change rapid detection and updating map technology, and put forward the criteria for road change rapid detection, integrated quality verification of update technology. It is expected that the results of this study will contribute to quality assurance of HD maps that support safety driving for automated vehicles.

• The Journal of Engineering Geology
• /
• v.28 no.4
• /
• pp.605-618
• /
• 2018

Korea follows the slope design criteria during construction. It was enacted by the Ministry of Land, Transport and Maritime Affairs. There are cases where the Soil-nail is designed as a measure to secure slope stability. The arrangement of the soil-nail may be arranged at equal intervals or may be arranged differently depending on the soil failure model. The optimum design of the countermeasure method is determined by securing stability of the slope through optimization of dimensions and shape. However, when uniform nails are placed at low elevations in slopes, the standard safety factor is exceeded, which may hinder economic design. It is preferable to arrange the reinforcement of the nails over the entire slope. When the horizontal spacing of the nails was topology optimized according to the slope height, it was possible to minimize the amount of reinforcement while satisfying the standard safety factor. Since the active load is reduced in the section where the slope height is lowered, the safety factor after reinforcement may be excessively increased. Therefore, the phase optimization method is proposed as an economical optimal design method using the reinforcing shape density. In addition, a relational expression was designed to optimize the horizontal spacing by slope height.