• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 추계학술대회 논문집
• /
• pp.85-88
• /
• 2007

현재 LED 전용의 렌즈로서 개발되어 있는 제품들은 대부분이 매우 좁은 빔각을 가지는 집광렌즈이지만 이를 사용하여 다양한 조명기구의 배광을 달성하기는 불가능하다. 본 논문에서는 가로등 형 배광을 가지는 대칭형, 비대칭형 배광을 가지는 선형 렌즈의 설계를 진행하고 그 성능을 시뮬레이션 하였다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 춘계학술대회 논문집
• /
• pp.182-185
• /
• 2009

조명용 광원으로써 LED의 사용이 늘어나고 있고, 앞으로도 더욱 늘어날 추세이다. 하지만 현재 출시되는 LED를 조명 용도에 적합한 배광을 구현하는 렌즈를 설계하는 작업은 설계 방법이 어렵고, 많은 반복 작업을 동반한다. 이에 새롭게 출시된 Photopia 3.0 Version의 PODT 기능을 이용해 LED 렌즈를 쉽게 설계할 수 있는 방법을 소개하고, 간단한 렌즈 설계를 수행 하였다.

• 조명전기설비학회논문지
• /
• 제18권2호
• /
• pp.8-15
• /
• 2004

본 논문은 RGB LED를 이용한 백색 전구의 색혼합 향상에 관한 것이다. RGB LED를 이용하여 전구를 설계하였을 경우, LED의 위치에 따라 광선의 진행 경로가 틀려 색혼합이 잘 되는 않는다. 따라서 각각의 LED에 경사렌즈를 씌워서 광선의 진행경로를 전구의 중심축으로 향하게 하여 주었다. 색혼합 정도는 MacAdam ellipse 이론을 이용하여 평가하였다.

• 한국안광학회지
• /
• 제10권4호
• /
• pp.255-259
• /
• 2005

난시 교정용 콘택트렌즈 착용 시 렌즈의 축 방향을 정확하게 하지 않을 경우이거나, 착용 후 순목 시 안검 등에 의해 콘택트렌즈가 회전할 경우가 있다. 이러한 현상이 있을 경우 완전교정상태가 잘못 교정된 상태로 되기 때문에 안정피로를 유발하여 시력의 저하를 가져올 수 있다. 이런 이유로 콘택트렌즈가 어느 정도 회전했는지의 파악이 필요하다. 콘택트렌즈가 회전했다면 착용 후 굴절검사에서 잔류 난시가 검출될 것이다. 이것을 이용해서 우리는 콘택트렌즈의 회전량을 계산하는 프로그램을 개발하였다.

• Design & Manufacturing
• /
• 제15권4호
• /
• pp.32-36
• /
• 2021

In this study, the cause of the decrease in transmittance of the outer lens among the causes of the decrease in the amount of light in the automobile headlamp was identified, and the improvement method was selected to determine the effect. The causes of defects that lower the transmittance of the outer lens are divided into a moisture problem and a haze problem. The moisture problem is caused by the temperature difference between the inside and the outside of the head lamp, and the haze problem occurs when the heat inside the head lamp evaporates the haze component contained in the plastic material and attaches it to the outer lens. In order to improve the haze problem that occurs in plastic raw materials, the structures of the bulb light source type headlamp and the LED chip light source type headlamp were analyzed. Among them, the housing material of the LED chip light source type headlamp, which is structurally prone to haze gas, was selected as the test target. In the mass-production injection process of the housing, the drying process was selected as a method to minimize haze gas without adding a separate production process. After extracting a sample every drying time at a constant drying temperature, the sample was put into a haze tester and the residual amount of haze gas was measured. As a result, it was confirmed that the residual amount of Haze gas in the material decreased as the drying time increased.

• Journal of the Optical Society of Korea
• /
• 제18권4호
• /
• pp.345-349
• /
• 2014

A direct-lit color-matching liquid crystal display using a lenticular lens array with grouped lens elements that image linear RGB light sources on the RGB subpixels of a color filter to enhance transmittance is designed, simulated, and fabricated. The RGB LED linear light sources were fabricated using small RGB LEDs in a linear array arrangement, and the lenticular lens array consisted of eight units of the same structure with a gap of 2.19 mm. The optical transmittance of the liquid crystal panel was improved by as much as 240% due to the color matching.

• 조명전기설비학회논문지
• /
• 제28권10호
• /
• pp.1-8
• /
• 2014

Heat dissipation of the high power LED is a critical issue. To estimate the junction temperature of the LED chip is most important in characterizing the heat dissipation, but it is impossible to directly measure it. In this study, surface temperatures of the 12.8W LED bulb was measured for 5 points using a data logger and compared with the simulated results using a thermal simulator based on FVM (finite volume method) to secure a reliability of the simulation. Effects of some factors such as lens, emissivity and air inlet were investigated using simulation works and then the results were analysed.

• Transactions on Electrical and Electronic Materials
• /
• 제18권1호
• /
• pp.35-41
• /
• 2017

This study looks at optimizinge light redistribution to improve the overall illuminance uniformity of commercial IRED modules. To obtain uniform illumination over a prescribed rectangular area, a freeform surface lens was evaluated using TracePro. The LED light overall illuminance uniformity regulated in KSC 7658 was verified using Relux software. Experimental test results showed 0.81 overall illuminance uniformity for rectangular light distribution of LED lights having a radiation angle of $80^{\circ}$. After fabricating prototype IRED lights based on these simulation results, illuminance performance was observed when used as actual IRED lighting with a nighttime CCTV system. Image observation photographs of the prototype $80^{\circ}$ rectangular IRED lights confirmed that object images can be seen clearly owing to high overall illuminance uniformity, and that dark regions of the CCTV screen were not shown.

• 광산업정보
• /
• 통권34호
• /
• pp.12-17
• /
• 2006

대만은 광산업 분야를 OE(Optoelectronics Components, FPD(Flat Panel Display), Optical Storage, Optical Lens Components & Laser Applications, OFC(Optical Fiber Communications, Optical Input & Output Devices 등 6개 대분류로 나누고 있으며 수년간 중점적으로 육성해 온 분야는 OE 및 FPD와 관련이 큰 LED 분야이다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.264-264
• /
• 2009

The sensitivity lighting of pendant type used Micro-controller AVR, embodiment method for Munsell chromaticity diagram system and adoption method for light source lens respectively. About a plan design of light fixture, LED circuit designed flow chart of circuits and LED driver of organizations in electron device. For used Solidworks soft ware program, LED light source must take a heat shink part and LED light fixture module for sensitivity lighting of pendant type into considerations