• Interaction and multiscale mechanics
• /
• 제3권2호
• /
• pp.192-211
• /
• 2010

In most framed structures the nonlinearities and the damages are localized, extending over a limited length of the structural member. In order to capture the details of the local damage, the segments of a member that have entered the nonlinear range may need to be analyzed using the three-dimensional element (3D) model whereas the rest of the member can be analyzed using the simpler one-dimensional (1D) element model with fewer degrees of freedom. An Element-Coupling model was proposed to couple the small scale solid 3D elements with the large scale 1D beam elements. The mixed dimensional coupling is performed imposing the kinematic coupling hypothesis of the 1D model on the interfaces of the 3D model. The analysis results are compared with test results of a reinforced concrete pipe column and a structure consisting of reinforced concrete columns and a steel space truss subjected to static and dynamic loading. This structure is a reduced scale model of a direct air-cooled condenser support platform built in a thermal power plant. The reduction scale for the column as well as for the structure was 1:8. The same structures are also analyzed using 3D solid elements for the entire structure to demonstrate the validity of the Element-Coupling model. A comparison of the accuracy and the computational effort indicates that by the proposed Element-Coupling method the accuracy is almost the same but the computational effort is significantly reduced.

• Steel and Composite Structures
• /
• 제44권5호
• /
• pp.721-740
• /
• 2022

In this paper, an accurate kinematic model has been developed to study the mechanical response of functionally graded (FG) sandwich beams, mainly covering the bending, buckling and free vibration problems. The studied structure with homogeneous hardcore and softcore is considered to be simply supported in the edges. The present model uses a new refined shear deformation beam theory (RSDBT) in which the displacement field is improved over the other existing high-order shear deformation beam theories (HSDBTs). The present model provides good accuracy and considers a nonlinear transverse shear deformation shape function, since it is constructed with only two unknown variables as the Euler-Bernoulli beam theory but complies with the shear stress-free boundary conditions on the upper and lower surfaces of the beam without employing shear correction factors. The sandwich beams are composed of two FG skins and a homogeneous core wherein the material properties of the skins are assumed to vary gradually and continuously in the thickness direction according to the power-law distribution of volume fraction of the constituents. The governing equations are drawn by implementing Hamilton's principle and solved by means of the Navier's technique. Numerical computations in the non-dimensional terms of transverse displacement, stresses, critical buckling load and natural frequencies obtained by using the proposed model are compared with those predicted by other beam theories to confirm the performance of the proposed theory and to verify the accuracy of the kinematic model.

• 한국자동차공학회논문집
• /
• 제20권4호
• /
• pp.16-24
• /
• 2012

This paper proposes a method utilizing Differential Global Position System (DGPS) with Real-Time Kinematic (RTK) and pre-built Geo-graphic Information System (GIS) to detect lane departure of a vehicle. The position of a vehicle measured by DGPS with RTK has 18 cm-level accuracy. The preconditioned GIS data giving accurate position information of the traffic lanes is used to set up coordinate system and to enable fast calculation of the relative position of the vehicle within the traffic lanes. This relative position can be used for safe driving by preventing the vehicle from departing lane carelessly. The proposed system can be a key component in functions such as vehicle guidance, driver alert and assistance, and the smart highway that eventually enables autonomous driving supporting system. Experimental results show the ability of the system to meet the accuracy and robustness to detect lane departure of a vehicle at high speed.

• Korean Journal of Geomatics
• /
• 제4권2호
• /
• pp.59-65
• /
• 2004

Recently, a lot of interest focuses on DGPS with which it is possible to obtain 3D geographic information in real time. There are some methods to transmit corrected signals which use ground based systems as beacon, as well as wireless and TV broadcasting media. However, these methods require a large number of stations. Therefore, when the distance from station to user is increased, there is a range limit to the transmission of corrected signals. In order to solve these problems, WADGPS method using Geo-satellite is being investigated. In this study, static and kinematic tests were performed by using Satloc SLX WADGPS and Ashtech receivers. The results showed that SA was affected most among corrected signals of WADGPS; it was followed by ionospheric delay, tropospheric delay and satellite orbit errors. The accuracy of static observation was approx. $\pm$1m on SA-on. This was ten times as accurate as that of absolute observation by common receiver on SA-off. In the SA-off, the accuracy of WADGPS can be improved further. The result of kinematic tests by WADGPS acted in concert with that of standard DGPS by C/A code. It was concluded that the application of W ADGPS could improve considerably navigation and the construction of geographic information.

• Journal of Positioning, Navigation, and Timing
• /
• 제5권4호
• /
• pp.221-233
• /
• 2016

This paper deals with performance assessment of the kinematic network-based GPS positioning technique with a view to using it for ellipsoidally referenced bathymetric surveys. To this end, two field trials were carried out on a land vehicle and a surveying vessel. Single-frequency GPS data acquired from these tests were processed by an in-house software which equips the network modeling algorithm with instantaneous ambiguity resolution procedure. The results reveals that ambiguity success rate based on the network model is mostly higher than 99.0%, which is superior to that of the single-baseline model. In addition, achievable accuracy of the technique was accessed at ${\pm}1.6cm$ and 2.7 cm with 95% confidence level in horizontal and vertical component respectively. From bathymetric survey at the West Nakdong River in Busan, Korea, 3-D coordinates of 2,011 points on its bed were computed by using GPS-derived coordinates, attitude, measured depth and geoid undulation. Note that their vertical coordinates are aligned to the geoid, the so-called orthometric height which is widely adopted in river engineering. Bathymetry was constructed by interpolating the coordinate set, and some discussion on its benefit was given at the end.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2737-2742
• /
• 2003

Kinematic calibration enhances absolute accuracy by compensating for the fabrication tolerances and installation errors. Effectiveness of calibration procedures depends greatly on the measurements performed. While the Cartesian postures are measured completely, all of the geometric parameters can be identified to their true values. With partial pose measurements, however, few geometric parameters may not be identifiable and effectiveness of the calibration results may vary significantly within the workspace. QR decomposition of the identification Jacobian matrix can reveal the non-identifiable parameters. Selecting postures for measurement is also an important issue for efficient calibration procedure. Typically, the condition number of the identification Jacobian is minimized to find optimum postures. This paper investigates identifiable parameters and optimum postures for four different calibration procedures - measuring postures completely with inverse kinematic residuals, measuring postures completely with forward kinematics residuals, measuring only the three position components, and restraining the mobility of the end-effector using a constraint link. The study is performed for a six degree-of-freedom fully parallel HexaSlide type paralle manipulator, HSM. Results verify that all parameters are identifiable with complete posture measurements. For the case of position measurements, one and for the case of constraint link, three parameters were found non-identifiable. Optimal postures showed the same trend of orienting themselves on the boundaries of the search space.

• 제어로봇시스템학회논문지
• /
• 제17권12호
• /
• pp.1256-1265
• /
• 2011

Automated parking assist systems are being commercialized and rapidly spread in the market. In order to improve odometry accuracy, we proposed a practical odometry calibration scheme of Car-Like Mobile Robot (CLMR). However, there were some open problems in our prior work. For example, it was not clear whether the kinematic parameters always converged or not using the proposed calibration scheme. In addition, test driving had to be carried out "twice" without detailed explanation. This research aims to provide answers for the addressed questions though the convergence property analysis of the calibration scheme. In this paper, we evaluate on the effect of the kinematic parameter error on the odometry error at the final pose by numerical computation. The evaluation will show that the wheel diameter and tread of the CLMR can be calibrated by iterative test drives. In addition, the region of convergence in the parametric space will be discussed. Presented experimental results clearly showed that the proposed calibration scheme would be useful in practical applications.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1476-1481
• /
• 2003

Kinematic calibration enhances absolute accuracy by compensating for the fabrication tolerances and installation errors. Effectiveness of calibration procedures depends greatly on the measurements performed. This paper investigates identifiable parameters and optimum postures for four different calibration procedures - measuring postures completely with inverse kinematic residuals, measuring postures completely with forward kinematics residuals, measuring only the three position components, and restraining the mobility of the end-effector using a constraint link. The study is performed for a six degree-of-freedom fully parallel HexaSlide type parallel manipulator, HSM. Results verify that all parameters are identifiable with complete posture measurements. For the case of position measurements, one and for the case of constraint link, three parameters were found non-identifiable. Selecting postures for measurement is also an important issue for efficient calibration procedure. Typically, the condition number of the identification Jacobian is minimized to find optimum postures. Optimal postures showed the same trend of orienting themselves on the boundaries of the search space.

• 한국측량학회지
• /
• 제19권1호
• /
• pp.39-45
• /
• 2001

장래 도로설계는 첨단정보이용이 편리해야하고, 자동차 항법체계(CNS : Car Navigation System)에 맞추어 차량유도기능을 극대화 할 수 있는 선형설계가 필요하다. 이렇게 되면 기존도로의 개량설계를 위하여 기존 도로의 선형을 정확히 분석할 필요가 있으며, 기존 도로의 설계도와 주요점의 좌표가 필요하게 된다. 기존 도로의 선형을 분석하기 위하여 본 연구에서는 동적(Kinematic) GPS측량으로 도로선형 Data를 짧은 시간에 손쉽게 취득하였고, 이 Data를 이용하여 도로의 평면선형을 분석하였다. 연구결과 관측된 도로선형 Data는 실용적인 오차범위 내에 포함되었으며, 선형분석도 실용성이 있음을 알 수 있었다.

• 전자공학회논문지SC
• /
• 제49권4호
• /
• pp.55-60
• /
• 2012

해상환경에서 감시장비의 운용시 원치 않는 외란 운동으로 장비의 안정화 성능이 저하된다. 본 논문에서는 선상 2축 감시장비의 정밀한 목표물 지향를 위해 자세정보의 좌표변환을 통해 움직임을 보상해주는 기구적 안정화를 적용하였다. 적용 결과, MEMS 센서의 떨어지는 정밀도와 기구적인 제약에 의해 오차를 더 줄일 없어 보완적인 기능으로 영상 안정화를 도입하였다. 또한 본 이중 안정화 방식의 실시간 실행을 위해 6축 운동 시뮬레이터를 포함한 테스트 베드를 구축하였으며, 하드웨어 포함 시뮬레이션 수행을 통해 본 방식의 유용성을 검증하였다.