• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.4
• /
• pp.105-111
• /
• 2019

In this paper, a performance analysis of waveguide broad-wall slot array antenna for millimeter-wave seeker in Ka-band was performed as using near-field measurement. The measurement of slot array antenna was conducted in both far-field and near-field. And the validation of near-field test in millimeter band was confirmed. It was confirmed that the beam pattern characteristics including beam width and side lobe level of the slot array antenna that performed the verification were the same. Differenced in the side lobe level of azimuth and elevation beam pattern were verified to be less than 1dB. Additionally, the new antenna aperture distribution was extracted as using back-projection method modifying the near-field data and then introduced the method conducting performance analysis of array antenna.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.3
• /
• pp.101-109
• /
• 2012

Because the installation problem of parabola antenna that is tilted to 45 degree when this antenna is installed at the area of middle latitude, the study on planar antenna in place of parabola antenna is made rapid progess. Especially, The development of the planar antenna for VSAT is needed depending on the increased Ka-band satellite communications. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level, the design method of the radiation power distribution control using the different slot widths is proposed. An array antenna consisting of 32 leakywave waveguide antennas is showing 35.16 dBi of gain, 2.5 degree of beamwidth at azimuth, below than -30 dB of sidelobe level, 45.8 degree of beam tilt angle in center frequency 30.2 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.142-149
• /
• 1999

In this paper, Aperture-coupled microstrip array antenna was designed and manufactured for satellite communication at Ka-Band. We analyzed a microstrip radiation element and designed power divider using $\lambda$g/4 transformer and T-junction power divider. A manufactured Aperture-coupled $2\times2$ microstrip array antenna has a resonant frequency of 20 GHz. The experimental results are as followings : resonant frequency of 19.62 GHz, VSWR 1.0692, return loss -29.61 dB, Bandwidth 1.76 GHz and -3 dB beamwidth $42^{\circ}$.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.297-302
• /
• 2005

Right hand circularly polarized Ka band microstrip patch array antenna was designed, manufacture and measurement were carried out. In order to lower axial ratio performance sequential rotation array technique was used. With mono-pulse feed There are sum and delta channel. Waveguide to microstrip transition was used. The 512 array antenna was performed which axial ratio is about 1.ldB in the half power beam width and also 1.ldB at the normal direction. Directivity gain of designed antenna is 32dB.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.3
• /
• pp.141-147
• /
• 2019

In this paper, a beam pattern performance analysis was performed according to number of array elements and spacing of the phase array antenna. The distance between array elements in an array structure design was reduced due to the electrical length of Ka-band, which increases the number of array elements in applying the aperture. If the number of elements reduce by widening the array distance, the grating lobes of the same size as the main beam will occur in visible region. If the number of array elements should be applied to a system where the number of array elements should be minimized, the analysis was performed on a plan to reduce the number of array elements and minimize degradation of performance, such as beam width and side lobe level.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.461-475
• /
• 2006

In this paper, it is described about the tri-band mobile antenna system design to provide broadband multimedia and direct broadcasting services using goo-stationary Koreasat 3, simultaneously operated in Ka/K/Ku band. The radiating part of the antenna system with a fan beam characteristic in the elevation plane is composed of the quasi-offset dual shaped reflector and the tri-band feeder. The tri-band feeder is also composed of the Ka/K dual band feeder with the protruding dielectric rod, the circular polarizer, the ortho-mode transducer and the circular-polarized Ku band feed array. Especially, the Ka/K dual band circular polarizer was realized firstly using the comb-type structure. For fast satellite-tracking on the movement, the Ku band feed array has the structure of the $2{\times}2$ active phased array which can make electrical beams. And, the circular-polarized characteristic in the feed array was improved by $90^{\circ}$ rotating arrangement of four radiating elements polarized circularly by a $90^{\circ}$ hybrid coupler, respectively. Four beam forming channels to make electrical beams at Ku band are divided into the main beam channel and the tracking beam channel in the output, and noise temperature characteristics of each channel were analyzed on the basis of the contributions of internal sub_units. From the fabricated antenna system, the output power at $P_{1dBc}$ of Ka_Tx channel was measured more than 34.1 dBm and the measured noise figures of K/Ku_Rx channels were less than 2.4 dB and 1.5 dB, respectively, over the operating band. The radiation patterns with co- and cross-polarization in the tri-band were measured using a near-field measurement in the anechoic chamber. Especially, Ku radiation patterns were measured after correcting each initial phase of active channels with partial radiation patterns obtained from the independent excitation of each channel. The antenna gains measured in Ka/K/Ku band of the antenna system were more than 39.6 dBi, 37.5 dBi, 29.6 dBi, respectively. And, the antenna system showed good system performances such as Ka_Tx EIRP more than 43.7 dBW and K/Ku_Rx G/T more than 13.2 dB/K and 7.12 dB/K, respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.2
• /
• pp.143-152
• /
• 2019

In this paper, we described the design of Ka-band planar active phased array antenna which is applicable for small RADAR for airborne and seeker of guided missile. The antenna consists of about 1000 array radiating elements and is designed to be within 200mm diameter. We optimized the spacing of radiating elements to allow beem steering above ${\pm}55$ degrees of Field of view, and analyzed the performance of antenna. We confirmed that the Effective Isotropic Radiated Power (EIRP) of the antenna can be 94.22 dBm and receive G/T can be 1.68 dB/k through the designs of RF components and the verification of RF budget. The TX output of TR Module is designed to be over 1.3W for EIRP, and Receive noise figure of TR Module is designed to be less than 5dB for G/T.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.140-144
• /
• 2013

This paper presents the novel design of circular polarized Ka-band horn array antenna. The element antenna of the arrya is composed of two parts, microstrip patch and square horn, and the microstrip patch is fed by corner truncated microstrip patch for circular polarization. The patch antenna has the role of a feeder and polarizer of the horn, thus the whole size of the horn antennae can be considerably reduced. The $1{\times}8$ horn array was designed and fabricated by the spacing of $0.9{\lambda}_0$ among the element horn. The element horn has typical gain of 8dBi and axial-ratio bandwidth of 4.9% at 3dB, and the minimum gain and axial-ratio bandwithd of the array is 14dBi and 8.2%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.1
• /
• pp.115-121
• /
• 2012

In this paper, the design and fabrication of slot array in the broad wall of the waveguide for Ka-band monopulse radar are discussed. The aperture distributions are designed for the desired antenna gain, beamwidth and Side-lobe Level(SLL), and then slot parameters, such as lengths and offsets, are obtained for corresponding to each slot admittance in the equivalent circuit by using Elliot's array synthesis procedure. MWS-CST simulation shows the return loss below -10 dB, antenna gain above 32 dBi, 3 dB beamwidth of 3.7 degree and SLL of -20 dB. In order to demonstrate the expected results, the designed antenna is fabricated and measured.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.69-77
• /
• 2009

Small size and low profile antenna for mobile vehicular-top-mounted is needed in satellite communication services such as DBS, Satellite Internet and VSAT. In middle latitudes, the development of an array antenna which has the conformal, low profile and 45 degree beam tilted configuration, and has the high gain with sharp beamwidth, low sidelobe and low loss is required for Ka band satellite communication. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level the radiation power control using a design method of the different slot width is proposed. An array antenna consisting of 32 leakywave elements is showing 34.4 dBi of gain, 3.6 degree of beamwidth, below than -25 dB of sidelobe level, 43 degree of beam tilt angle in center frequency 20.0 GHz. Feed network designed by waveguide cooperated feed shows good performance of wideband and low loss.