• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.2059-2066
• /
• 2018

This study explored the feasibility of utilizing an SWCNT-coated fabric sensor for the development of a wearable motion sensing device. The extent of variation in electric resistance of the sensor material was evaluated by varying the fiber composition of the SWCNT-coated base fabrics, attachment methods, number of layers, and sensor width and length. 32 sensors were fabricated by employing different combinations of these variables. Using a custom-built experimental jig, the amount of voltage change in a fabric sensor as a function of the length was measured as the fabric sensors underwent loading-unloading test with induced strains of 30 %, 40 %, and 50 % at a frequency of 0.5 Hz. First-step analysis revealed the following: characteristics of the strain-voltage curves of the fabric sensors confirmed that 14 out of 32 sensors were evaluated as more suitable for measuring human joint movement, as they yield stable resistance values under tension-release conditions; furthermore, significantly stable resistance values were observed at each level of strain. Secondly, we analyzed the averaged maximum, minimum, and standard deviations at various strain levels. From this analysis, it was determined that the two-layer sensor structure and welding attachment method contributed to the improvement of sensing accuracy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.459-467
• /
• 2016

Recently, new open-cut modular construction method, which is built within a 5~7m depth below the road, was proposed for the near-surface transit system to ensure the economic feasibility of underground structures. In this paper, the precast modular construction method was developed for the low-cost and rapid construction of underground structures. For the experiment on the flexural performance of the modular slab connections, a total of eleven specimens were fabricated according to the test variables; section shape, joint type, lap length, and transverse reinforcement. The test results were compared with those of the specimens without loop joints. To verify the performance of the slab connections, the 4-point loading tests of precast RC members with loop joints were conducted. As a result of the test, the flexural performance of the half-depth specimens with a 200mm lap length of loop joints were confirmed to be similar to those of the specimens without joints.

• Korean Journal of Applied Biomechanics
• /
• v.26 no.4
• /
• pp.413-420
• /
• 2016

Objective: The purpose of this study was to analyze and compare different kinds of outdoor walking shoes in terms of muscle fatigue and ground reaction force on walking, and to provide foundational data for developing and choosing outdoor walking shoes that fit the users. Method: The study subjects were 30 healthy men. The experiment was conducted by using outdoor walking shoes with different inner and outer harnesses of the midsole, and shapes of the outsole. For data collection, electromyography was used to measure the muscle fatigue of the anterior tibial muscle and gastrocnemii, which contribute to the dorsiflexion and plantarflexion of the ankle joint, and the biceps muscle of the thigh and lateral great muscles, which contribute to the flexion and extension of the knee joint. A GRF measurement device was used to measure the X, Y, and Z axes. Results: In the type A outdoor walking shoes, regarding the hardness of the midsole, the inner part was soft, while the outer part was hard. The vertical ground reaction force was the lowest, which means least impact while walking and light load to the knees and ankles. The type C outdoor walking shoes were intended to provide a good feel in wearing the shoes. The tibialis anterior, biceps femoris, and gastrocnemii indicate low fatigue, which means that during a long-distance walk, it will minimize the fatigue in the muscles of the lower limbs. Conclusion: To sum up the study results, the different types of outdoor walking shoes indicate their unique characteristics in the biomechanical comparison and analysis. However, the difference was not statistically significant. Thus, a systematic and constant follow-up research should be conducted to cope with expanding market for outdoor walking shoes. Lastly, this study is expected to present foundational data and directions for developing outdoor walking shoes.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.9
• /
• pp.1026-1034
• /
• 2012

The purpose of this study was to verify the validation of effect on improvement of muscle strength unbalance according to exercise load deviation during rowing exercise. We performed evaluation of muscular activity and joint torque before the test. We recruited twenty subjects who one side's muscle strength is bigger in more 20% than other side. Subjects divided two groups. One is dominant left side and the other was dominant right side. Subjects performed rowing exercise in electric load deviation rowing equipment (Robo.gym, Humonic Co., Ltd., Daegu, Korea). Exercise performed four sets a day including 25 times a set, and three days a week. Measurements consist of evaluation of muscular activity and joint torque. Exercise load deviation adapted that different value of muscle strength in both arms multiplied 1RM% and added 1RM 50%. The results in adapted load deviation showed that the differences of maximal peak torque in 22.75% were getting increase significantly during exercise in 5.72%. This interpreted that rowing exercise with loading deviation types could provide muscle strength and muscular endurance exercise in same time for balance. Our study found out that loading deviation could provide muscle strength and muscular endurance exercise for improving muscle unbalance.

• Korean Journal of Metals and Materials
• /
• v.47 no.8
• /
• pp.500-507
• /
• 2009

Pb-free solder has recently been used in electronics in efforts to meet environmental regulations, and a number of Pb-free solder alloy choices beyond the near-eutectic SnAgCu solder are now available. With increased demand for thin and portable electronics, the high cost of alloys containing significant amounts of silver and their poor mechanical shock performance have spurred the development of low Ag SnAgCu solder, which provides improved mechanical performance at a reasonable cost. Although low Ag SnAgCu solder exhibits significantly higher fracture resistance under high-strain rates, little thermal fatigue data exist for this solder. Therefore, it is necessary to investigate thermal fatigue reliability of low Ag SnAgCu solder under variation of thermal stress in order to allow its implementation in electronic products with high reliability requirements. In this study, the reliability of Sn0.3Ag0.7Cu(SAC0307), a low Ag solder alloy, is discussed and compared with that of Sn3Ag0.5Cu(SAC305). Three sample types and six samples size are evaluated. Mechanical properties and microstructure of the solder joint are investigated under thermal shock cycles. It was observed that the mechanical strength of SAC0307 dropped slightly with thermal cycling relative to that of SAC305. This reveals that the failure mode of SAC0307 is different from that SAC305 under this critical condition.

• Journal of The Geomorphological Association of Korea
• /
• v.19 no.1
• /
• pp.83-97
• /
• 2012

Slopes of Seoseokdea~ Jangbuljae, at Mt. Moodeung, appears repeatedly the cliffs are mostly greater than $70^{\circ}$, and the planations maintain around $5^{\circ}$ in general. They studied the creation of development environments, cryoplanation are mainly facing the southwest. It is assumed that rock falling had been wostly occurred under a periglacial environment through jointing due to repeated freezing and thawing. Planation at the bottom of Columnar joint are described structural benches. Movement precesses of planation matrix are solifluction or jelifluction. The result of age determination of the slopes in Jangbuljae tells that the upper part of Ibseokdae has been remaining exposed to the land surface from 110,000 year ago. The blocks in the bottom part has been exposed to the surface around 10,000 year ago while Jangbuljae has been exposed to the surface about 50,000 year ago. It was assumed that they moved to the current location since being separated from columnar joint after exposure to the surface.

• The Journal of the Korea Contents Association
• /
• v.21 no.9
• /
• pp.714-722
• /
• 2021

In this study, intends to propose virtual reality education contents for fundamental nursing skills to develop various teaching methods in nursing education. Blood sugar test & insulin subcutaneous injection among the 20 core fundamental nursing skills is one of that frequently performed and can be used for self-management education for diabetic patients. This study designed a core fundamental nursing skill on immersive VR contents by dividing the learner's experience into three stages: guide, mission, and feedback with these skills. And it is designed by tracking the movement of the hand through finger joint recognition without using a controller for immerse in training. This study will help develop VR nursing education contents that can improve clinical practice competency and the effect of the nursing education.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.8
• /
• pp.661-669
• /
• 2021

A mechanical stiffener has been mainly applied on a PCB to secure fatigue life of a solder joint of an electronic components in spaceborne electronics by minimizing bending displacement of the PCB. However, it causes an increase of mass and volume of the electronics. The high damping PCB implemented by multi-layered viscoelastic tapes of a previous research was effective for assuring the fatigue life of the solder joint, but it also has a limitation to decrease accommodation efficiency for the components on the PCB. In this study, we proposed high damping PCB with a multi-layered superelastic shape memory alloy stiffener for spatialminimized, light-weighted, high-integrated structure design of the electronics. To investigate the basic characteristics of the proposed PCB, a static load test, a free vibration test were performed. Then, the high damping characteristic and the design effectiveness of the PCB were validated through a random vibration test.

• Journal of muscle and joint health
• /
• v.26 no.1
• /
• pp.15-26
• /
• 2019

Purpose: The purpose of this study was to develop a Dongsasub training applying aroma necklace for nursing students in clinical practicum, and to evaluate the training programs' effects on perceived stress, self-esteem, depression, and clinical competence of the participants. Methods: This study used a cluster-randomized controlled trial design. Participants were 56 nursing students taking clinical practicum courses (26 in the experimental group and 30 in the control group). The training program consisted of four sessions of Dongsasub training and wearing a necklace where a mixture of aroma oils attached. Participants in experimental group were given a necklace with essential oil mixture of lavender, bergamot, and geranium with the ratio of 1:1:1 for 2 weeks. The control group received no intervention. Outcome variables included perceived stress, self-esteem, depression, and clinical competence. Data were analyzed with Fisher's exact test, Chi-square, Independent t-test using the SPSS/WIN 21.0. Results: Independent t-test revealed that perceived stress (t=3.15, p=.003), depression (t=4.62, p<.001) were significantly lower in the experimental group than the control group; self-esteem (t=-3.03, p=.004), clinical competence (t=-2.15, p=.036) scored significantly greater than the control group. Conclusion: The results indicate that the Dongsasub training with application of the aroma necklace can be used as an effective nursing intervention for lowering perceived stress, depression and improving self-esteem, clinical competence of nursing students.

• Journal of muscle and joint health
• /
• v.26 no.2
• /
• pp.111-119
• /
• 2019

Purpose: This study investigated the effects of nursing organizational culture and self-leadership on job satisfaction for nurses working in the comprehensive nursing care service ward in public hospitals. Methods: The participants were 138 nurses working in Gyeonggi-do medical center. The collected data were analyzed using descriptive statistics, t-test, ANOVA, Pearson's correlation coefficients, and regression analysis with SPSS/WIN 23.0. Results: Factors affecting job satisfaction were innovation-oriented culture (${\beta}=.29$, p<.001), want to work in this department (${\beta}=-.25$, p<.001), the cognitive strategy of self-leadership (${\beta}=.23$, p=.002), hierarchical-oriented culture (${\beta}=-.21$, p=.002), and marital status (${\beta}=.18$, p=.005). These factors accounted for 42.0% of the variability in job satisfaction. Conclusion: In order to improve the job satisfaction of nurses in the comprehensive nursing care service ward in public hospitals, institutional-level efforts should be made to encourage an innovation-oriented culture and avoid a hierarchy-oriented culture. In addition, education and program development are needed to improve the cognitive strategy of self-leadership.