• 한국가시화정보학회지
• /
• 제20권3호
• /
• pp.58-66
• /
• 2022

The high heat emitted from the process module and heat jacket may cause errors in semiconductor process equipment. Barriers were designed to reduce the temperature of surface on transfer module. A designed barrier was compared and analyzed by numerical analysis using ANSYS Fluent. The average temperature of barrier and effect of radiation heat transfer were also compared through absorbed radiative heat flux of the barrier. The adoption of the barrier had an effect on the radiative heat transfer reduction of the transfer module rod. The effect of the angles of barrier from 50° to 90° on the heat transfer was investigated using the absorbed radiative heat flux with the average temperature. The angle of barrier of 50° reduced the temperature up to 9.6 %.

• 한국융합학회논문지
• /
• 제12권2호
• /
• pp.185-191
• /
• 2021

본 자동차 실린더 블록 주조시 실린더 보어 내에서 발생하는 열로부터 구조적 변형을 방지하는데 필요한 워터 자켓 코어용 주물사의 특성을 분석하였다. 샌드 코어의 특성평가를 위하여 인장강도 시험기, 입도 지수(AFS-GFN), 광학현미경을 사용하였다. 주물사의 SiO2 함량이 높으면 고온팽창에 의한 치수 불량, 베이닝 불량이 발생하며, 너무 낮으면 코어 파손, 기포, 화학적 소착 등이 발생하였다. 입도 지수와 입형이 코어강도와 레진 소비량에 영향을 미치고, 이로 인한 불량 유형 변화가 발생하였다. 건조사가 염분이 높을수록 코어 강도는 감소하며, 알칼리성일수록 코어 강도가 감소하였다. 레진 함량 1.6~1.8%에서 1시간 경화 이후에 코어 강도 증가는 대략 최대를 보였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.615-620
• /
• 1996

생산성의 향상을 위하여 공작기계의 고속가공이 필요하고 이를 위한 연구가 상당히 진행되고 있다. 단위 시간당 절삭량을 올리고 알루미늄과 같은 연질 금속의 가공을 위하여 주축을 고속화하는 것이 매우 중요하나, 각 요소간의 마찰로 인한 발열에 의해 베어링의 수명단축이나 열변형 등을 동반하여 정밀도가 떨어지게 된다.(중략)

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기설비전문위원
• /
• pp.90-92
• /
• 2005

When the jacket damaged conductors in 22.9kV-y overhead distribution lines are contacted with the metal material by strong wind, which, leads to are melting as well as faults accordance. The duration of the arc temperature due to flame effected by weather and flash over conditions. In order to simulated the worst conditions, the ACSR-OC($58mm^2$) used as specimen was artificially cut in no wind. After contacting the two cut conductors again the testing current was applied. thus, the changes in temperature of are flame was analyzed.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.50-55
• /
• 2012

The important problem in high speed spindle is to reduce and minimize the thermal effect by motor and bearing. This paper presents the thermal characteristic analysis for a high speed spindle with and without cooling at the rear part, considering the viscosity and the flow rate of cooling oil. A high speed spindle is composed of angular contact ceramic ball bearings, high speed built-in motor, oil jacket cooling and so on. The thermal analyses of high speed spindle need to minimize the thermal effect and maximize the cooling effect and they are carried out under the various cooling conditions. Heat generations of the bearing and the high speed motor are estimated from the theoretical and experimental data. This result can be applied to the design and manufacture of a high speed motor spindle.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.421-425
• /
• 2009

재생냉각형 액체로켓 연소기 챔버에서 열차폐 코팅이 미치는 열/구조적인 영향에 대하여 유한요소 해석을 통하여 고찰하였다. 열차폐 코팅은 현재 개발하고 있는 연소기에 사용되는 NiCrAlY-$ZrO_2$과 향후 적용할 가능성이 있는 Ni-Cr 두 종류를 적용하였다. 열/구조해석 결과 NiCrAlY-$ZrO_2$ 코팅이 Ni-Cr 코팅에 비하여 열차폐에 의한 온도감소 효과가 크게 나타났다. 결과적으로 냉각채널의 온도와 변형 또한 NiCrAlY-$ZrO_2$ 코팅을 적용하였을 때 Ni-Cr 코팅보다 감소하였다. 외측구조물의 구조안정성에 있어서 Ni-Cr 코팅이 미치는 영향은 없었으나, NiCrAlY-$ZrO_2$ 코팅은 외측구조물의 유효응력을 감소시켜 챔버의 구조안정성을 증가시켰다.

• 한국자동차공학회논문집
• /
• 제1권1호
• /
• pp.14-21
• /
• 1993

The effect of coolant flow pattern on the metal temperature of the combustion chamber was studied in 1.5L and 1.8L gasoline engines. One of the main important points in the design of the water jacket is the increase of the coolant flow velocity. In this paper, the water jackets of the cylinder head and the cylinder block were visualized for the purpose of improving the coolant flow pattern. By the use of this technique, the optimal design of the size and th location of the water transfer fole was possible. And, to lower the metal temperatures of the thermally critical parts, the drilled water passages were employed. To investigate of effect of the improved flow pattern and the drilled water passages, the metal temperatures of the combustion chamber were measured. As a result of the temperature measurement, it was found out that both the change of flow pattern and the drilled water passages have significant effect on the reduction of the peak metal temperature.

• 대한가정학회지
• /
• 제29권2호
• /
• pp.35-46
• /
• 1991

After adhering theone-sided non-woven adhesive interlining to the polyester/cotton fabrics and making experiments under the various conditions by L27 Orthogonal Array Table, we examined and analyzed the breaking away strength. The rusults are summarized as follows : 1. The best length of the adhering time is 15 secs. 2. As the adehesive interlining for blouse and jacket, B3 is best 3. The pressure for the adhesion is best under the pressure of 6.2Kg. 4. The temperature for the adhesion is best at 140$^{\circ}C$. 5. As for the direction of the adhesion, three directions appear much the same breaking away strength. 6. For the better adhesion power, if the less adhering power, if the less adhering pressure is applied, the adhering time must be extended(15-20 secs), and if much stronger adhering pressure is applied, the time must be shortened(10-15 secs). In general, it is the best way for the adhesion to apply under the pressure of 6.2Kg, for 15 secs long, and at 140$^{\circ}C$ of the adhering temperature.

• 대한기계학회논문집B
• /
• 제22권8호
• /
• pp.1183-1194
• /
• 1998

This paper describes a theoretical model developed for analyzing the heat transfer of automotive cooling systems. From the model, heat transfer rate of automotive cooling systems can be predicted, providing useful information at the early stages of the design and development. The aim of the study is to develop a simulation program for automotive cooling system analysis and a performance analysis program for analyzing heat exchanger. Heat release rate from combustion gas to coolant through cylinder wall in engine cylinder was analyzed by using a two zone combustion model. This paper studied how cooling condition would affect engine heat release rate and measured temperature distribution of coolant in water jacket.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.237-242
• /
• 2001

This paper presents the thermal characteristics analysis of a high-speed HMC spindle system with angular contact ball bearings, built-in motor, oil-jet lubrication method, oil jacket cooling method, and so on. The spindle system is composed of the main spindle and sub-spindle which are mechanically connected by a flexible coupling. The spindles are supported by two front and rear bearings, and the built-in motor is located between the front and rear bearings of the sub-spindle. The thermal analysis model of spindle system is constructed by the finite element method, and the thermal characteristics in the design stage are estimated based on temperature distribution, heat flow and thermal deformation under the various testing conditions related to material of bearing ball, spindle speed and coolant temperature.