• Carbon letters
• /
• v.15 no.3
• /
• pp.187-191
• /
• 2014

This study reports on the influence of N-butyl-N-methylpyrrolidinium tetrafluoroborate ($PYR_{14}BF_4$) ionic liquid additive on the conducting and interfacial properties of organic solvent based electrolytes against a carbon electrode. We used the mixture of ethylene carbonate/dimethoxyethane (1:1) as an organic solvent electrolyte and tetraethylammonium tetrafluoroborate ($TEABF_4$) as a common salt. Using the $PYR_{14}BF$ ionic liquid as additive produced higher ionic conductivity in the electrolyte and lower interface resistance between carbon and electrolyte, resulting in improved capacitance. The chemical and electrochemical stability of the electrolyte was measured by ionic conductivity meter and linear sweep voltammetry. The electrochemical analysis between electrolyte and carbon electrode was examined by cyclic voltammetry and electrochemical impedance spectroscopy.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.105-108
• /
• 2011

The cycling behavior of $Li_4Ti_5O_{12}$ electrode in the ionic liquid (IL)-based electrolytes containing 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl) imide and a small amount of additive (vinylene carbonate, ethylene carbonate, fluoroethylene carbonate) was investigated. The $Li_4Ti_5O_{12}$ electrode in the IL electrolyte with an additive exhibited reversible cycling behavior with good capacity retention. Electrochemical impedance spectroscopy and FTIR studies revealed that an electrochemically stable solid electrolyte interphase was formed on the $Li_4Ti_5O_{12}$ electrode in the presence of vinylene carbonate and ethylene carbonate during cycling.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.777-783
• /
• 1994

Oxidation behavior of hot-pressed silicon nitride ceramics with various sintering additives has been investigated. The weight gain of each specimens has shown in the range of 0.11 mg/$\textrm{cm}^2$ ~3.4 mg/$\textrm{cm}^2$ at 140$0^{\circ}C$ for 192 h and eleven compositions have shown good oxidation resistance with the weight gain below 0.5 mg/$\textrm{cm}^2$. The oxidation rate has been shown to obey the parabolic rate law and the oxidized surface has consisted of $\alpha$-cristobalite and M2Si2O7 or MSiO3 (M=rare earth or transition metals) phase. The oxidation rate of each specimens has related to the eutectic temperature between additive oxide and SiO2, and ionic radius of additive oxides, respectively. From the above results, it could be concluded that the oxidation behavior of hot pressed silicon nitride is dominated by the high temperature properties of grain boundary glassy phase and the high temperature properties of grain boundary glassy phase are affected by the ionic radius of additive oxides.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.4
• /
• pp.453-457
• /
• 2021

Lithium-sulfur (Li-S) batteries are one of attractive energy conversion and storage system based on high theoretical specific capacity and energy density with low costs. However, volatile nature of elemental sulfur is one of critical problem for their practical acceptance in industry because it considerably affects electrode uniformity during electrode manufacturing. In this work, polymeric sulfur composite consisting of ionic liquid (IL) are suggested to reduce volatility nature of elemental sulfur, resulting in better processibility of the Li-S cell. According to systematic spectroscopic analysis, it is found that polymeric sulfur is consisting of repeating units combining with elemental sulfur and volatility of them is negligible even at high temperature. In addition, the IL-embedded polymeric sulfur shows moderate cycle performance compared to the cell with elemental sulfur. From these results, it is found that the IL-embedded polymeric sulfur composite is applicable cathode candidate for the Li-S cell based on their excellent non-volatility as well as their superior electrochemical performance.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.279-284
• /
• 2021

The high theoretical specific capacity of lithium-sulfur (Li-S) batteries makes them a more promising energy storage system than conventional lithium-ion batteries (LIBs). However, the slow kinetics of the electrochemical conversion reaction seriously hinders the utilization of Li-S as an active battery material and has prevented the successful application of Li-S cells. Therefore, exploration of alternatives that can overcome the sluggish electrochemical reaction is necessary to increase the performance of Li-S batteries. In this work, an ionic liquid (IL) is proposed as a functional additive to promote the electrochemical reactivity of the Li-S cell. The sluggish electrochemical reaction is mainly caused by precipitation of low-order polysulfide (l-PS) onto the positive electrode, so the IL is adopted as a solubilizer to remove the precipitated l-PS from the positive electrode to promote additional electron transfer reactions. The ILs effectively dissolve l-PS and greatly improve the electrochemical performance by allowing greater utilization of l-PS, which results in a higher initial specific capacity, together with a moderate retention rate. The results presented here confirmed that the use of an IL as an additive is quite effective at enhancing the overall performance of the Li-S cell and this understanding will enable the construction of highly efficient Li-S batteries.

• KSBB Journal
• /
• v.28 no.4
• /
• pp.238-243
• /
• 2013

Astaxanthin is one of the carotenoid with strong antioxidant. The conditions of extraction of astaxanthin from Portunus trituberculatus were optimized in this work. Six factors of conditions such as, extraction method, extraction solvent, ratio of solvent to raw material, temperature, and time, were investigated. For the increase of the extraction yield, ionic liquids were used as additives in the extraction solvent. The optimum extraction conditions were found: heat reflux extraction, Dichloromethane/methanol (25:75, v/v) as solvent, 1:30 of the ratio of solvent raw material, $80^{\circ}C$, 90 min, and ionic liquid as additive. As a result, 45.81 ${\mu}g/g$ of astaxanthin was extracted from waste.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.12
• /
• pp.3057-3060
• /
• 2009

Ionic palladium(II) complex, [($Me_4en)Pd(L)]_2(ClO_4)_4\;(Me_4$en = N,N,N',N'-tetramethylethylenediamine; L = bis-(4-(4-pyridylcarboxyl)phenyl)methane), allows to form a monodisperse submicrosphere without any template or additive. Surface-perchlorates on the submicrosphere have been exchanged by anionic pH indicators such as thymol blue, bromothymol blue, and bromocresol green. The ionic and amphiphilic properties of the palladium(II) complex appear to be primarily associated with the formation and easy surface-anion exchange of submicrosphere. The surface-anion exchange through the electrostatic interaction is a very good tool for the surface-modification. The color of the pH indicator-exchanged submicrospheres is very sensitive to pH and Hg$^{2+}$ cation, and thus they are promising to submicrospherical indicators.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2299-2302
• /
• 2007

A series of quaternary ammonium-based ionic liquids (ILs) containing an alkyl carbonate group on the cation was first prepared and their physical and electrochemical properties including density, viscosity, thermal stability, electrochemical stability, and ionic conductivity were reported. These ILs exhibited wide electrochemical windows of at least 5.0 V and relatively high conductivities. In contrast to dialkyl-substituted ionic liquids, the ILs with an alkyl carbonate group on the cation showed much smaller drop in conductivities when mixed with a lithium salt, due to the interaction of lithium ions with carbonate groups. Upon interaction with a Li salt, the carbonyl stretching frequency of the carbonate group shifted to a lower frequency whereas the peak associated with C-O single bond moved to a higher frequency.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.712-718
• /
• 2016

In this study, we investigate the effect of the$Li_3BO_3$ additive on the densification and ionic conductivity of garnet-type $Li_7La_3Zr_2O_{12}$ solid electrolytes for all-solid-state lithium batteries. We analyze their densification behavior with the addition of $Li_3BO_3$ in the range of 2-10 wt.% by dilatometer measurements and isothermal sintering. Dilatometry analysis reveals that the sintering of $Li_7La_3Zr_2O_{12}-Li_3BO_3$ composites is characterized by two stages, resulting in two peaks, which show a significant dependence on the $Li_3BO_3$ additive content, in the shrinkage rate curves. Sintered density and total ion conductivity of the system increases with increasing $Li_3BO_3$ content. After sintering at $1100^{\circ}C$ for 8 h, the $Li_7La_3Zr_2O_{12}-8$ wt.% $Li_3BO_3$ composite shows a total ionic conductivity of $1.61{\times}10^{-5}Scm^{-1}$, while that of the pure $Li_7La_3Zr_2O_{12}$ is only $5.98{\times}10^{-6}Scm^{-1}$.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.12
• /
• pp.601-607
• /
• 2002

IPMC(Ionic Polymer Metal Composite)actuators were optimized for producing improved forces by changing multiple parameters including repetition of number of plating, surface electroding and additive(PVP)-treatment on reduction. The platinum electrode is deposited on the surface of the material where platinum particle stay in a dense form that appears to introduce a significant level of surface electrode resistance. Actuation tests were performed for such IPMC actuators under a low voltage. The test results show that the lower surface-electrode resistance generates higher actuation capability in the IPMC actuators. In order to investigate relaxation behavior of bending and repeatability in dry condition, the IPMC was coated by$rubber(KRATON^{TM})$to minimize the effect of water evaporation from IPMC. This actuator can be used in air with surface coating to avoid membrane drying.