• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.570-582
• /
• 2012

In the communication, a reconfigurable antenna using two PIN diodes is presented for quad-band(GSM900/GSM1800/GSM1900/UMTS) mobile handset applications. The proposed antenna has a size $45{\times}11{\times}6mm^3$. By independently adjusting the on/off states of two PIN diodes located on the radiating element, the proposed structure can be operated in the PIFA and loop mode, respectively. The PIN diodes are replaced by conducting tape in order to verify the concept. In regards to the fabricated reconfigurable antenna, when operating in the PIFA mode, the measured results show that the 7 dB bandwidth is 8.62 %. which covers the GSM900(880~960 MHz) band. When operating in the loop mode, the measured results show that the 7 dB bandwidth is 26.36 %, which covers the GSM1800(1,710~1,880 MHz), GSM1900(1,850~1,990 MHz), and UMTS(1,920~2,170 MHz) bands, respectively.

• Journal of the Korean Ceramic Society
• /
• v.43 no.11 s.294
• /
• pp.715-723
• /
• 2006

Perovskite oxide materials are very important for the electronics industry, because they exhibit promising properties. With an interest in the obvious applications, significant effort has been invested in the growth of highly crystalline epitaxial perovskite oxide thin films in our laboratory. And the desired structure of films was formed to achieve excellent properties. $Y_1Ba_2Cu_3O_{7-x}$ (YBCO) superconducting thin films were simultaneously deposited on both sides of 3 inch wafer by inverted cylindrical sputtering. Values of microwave surface resistance R$_2$ (75 K, 145 GHz, 0 T) smaller than 100 m$\Omega$ were reached over the whole area of YBCO thin films by pre-seeded a self-template layer. For implementation of voltage tunable high-quality varactor, A tri-layer structured SrTiO$_3$ (STO) thin films with different tetragonal distortion degree was prepared in order to simultaneously achieve a large relative capacitance change and a small dielectric loss. Highly a-axis textured $Ba_{0.65}Sr_{0.35}TiO_3$ (BST65/35) thin films was grown on Pt/Ti/SiO$_2$/Si substrate for monolithic bolometers by introducing $Ba_{0.65}Sr_{0.35}RuO_3$ (BSR65/35) thin films as buffer layer. With the buffer layer, the leakage current density of BST65/35 thin films were greatly reduced, and the pyroelectric coefficient of $7.6\times10_{-7}$ C $cm^{-2}$ $K^{-1}$ was achieved at 6 V/$\mu$m bias and room temperature.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1313-1314
• /
• 2007

This paper presents organic thin-film transistors (OTFTs) with poly(3-hexylthiophene)(P3HT) semiconductor and several polymeric dielectric materials of poly(vinyl phenol)(PVP), poly(vinyl alcohol)(PVA), and polyimide(PI) by using soluble process. The fabricated OTFT's have inverted staggered structure using transmission line method(TLM) pattern. In order to evaluate the electrical characteristics of the OTFT, capacitance-voltage(C-V) and current-voltage(I-V) were measured. C-V graphs were measured at several frequencies of 100 Hz, 1 kHz, and 1 MHz and ID-VDS graphs according to $V_{GS}$. The current on/off ratio and threshold voltage with each of PVP, PVA, and PI based OTFTs were measured to $10^3$, and -0.36, -0.41, and -0.62 V. Also, the calculated mobility with each of PVP, PVA, and PI was 0.097, 0.095, and 0.028 $cm^{2}V^{-1}s^{-1}$, respectively. In the cases of PVP and PVA, the hole mobility of P3HT was in excellent agreement with the published value of 0.1 $cm^{2}V^{-1}s^{-1}$.

• Journal of radiological science and technology
• /
• v.28 no.1
• /
• pp.19-24
• /
• 2005

The purpose of this study was to design and implement a useful annotation-based Radiological image retrieval system to accurately determine on education and image information for Radiological technologists. For better retrieval performance based on large image databases, we presented an indexing technique that integrated $B^+-tree$ proposed by Bayer for indexing simple attributes and inverted file structure for text medical keywords acquired from additional description information about Radiological images. In our results, we implemented proposed retrieval system with Delphi under Windows XP environment. End users, Radiological technologists, are able to store simple attributes information such as doctor name, operator name, body parts, disease and so on, additional text-based description information, and Radiological image itself as well as to retrieve wanted results by using simple attributes and text keywords from large image databases by graphic user interface. Consequently proposed system can be used for effective clinical decision on Radiological image, reduction of education time by organizing the knowledge, and well organized education in the clinical fields. In addition, It can be expected to develop as decision support system by constructing web-based integrated imaging system included general image and special contrast image for the future.

• Restorative Dentistry and Endodontics
• /
• v.21 no.2
• /
• pp.559-568
• /
• 1996

The purpose of this study was to evaluate the micro leakage of composite resin when various phosphoric acid agents were used to etch the enamel and dentin. In this study, class V cavities were prepared on the buccal surfaces of fourty extracted human molar teeth, and they were randomly assigned into 4 groups with 10 teeth. The cavities of each groups were etched with 10%, 32%, 35% and 37% phosphoric acids for 15 seconds, washed and dried and the cavities were restored with composite resin after application of the adhesive. The specimens were immersed in 2% methylene blue solution for 3 days. And then, the specimens were sectioned buccoligually. Degree of dye penetration at tooth-restoration interfaces was examined by Inverted Metallurgical Microscope at the occlusal and gingival margins. The result were as follows : 1. The degree of microleakage at occlusal and gingival margin in all group was statistically difference among 10% and 35% (P<0.01), 10% and 37% (P<0.01), 32% and 35% (P<0.05) and 32% and 37% (P<0.05) acid concentrations, but was not statistically difference between 10% and 32%, 35% and 37% acid concentrations (P>0.05). The degree of microleakage was showed to dimish with increase of acid concentration. 2. The degree of microleakage at the occlusal margin was statistically significant difference among 10% and 32%,10% and 35%, 10% and 37% acid concentrations(P<0.05). The degree of microleakage among 32% and 35%, 32% and 37% and 32% and 37% acid concentrations was not statistically significant difference. 3. In comparison of microleakage at the gingival margin, the degree of microleakage above 32% acid concentration was not showed less than 10% acid concentration (P>0.05). In comparison of 32%, 35%, 37% acid concentrations, the degree of microleakage at 35% and 37% acid concentrations was showed less than 32% acid concentration(P<0.05).

• Current Photovoltaic Research
• /
• v.7 no.3
• /
• pp.55-60
• /
• 2019

Polymer:nonfullerene solar cells with an inverted-type device structure were fabricated by employing the bulk heterojunction (BHJ) active layers, which are composed of poly[(2,6-(4,8-bis(5-(2-ethylhexyl)thiophene-2-yl)-benzo[1,2-b:4,5-b']dithiophene))-alt-(5,5-(1',3'-di-2-thienyl-5',7-bis(2-ethylhexyl)benzo[1',2'-c:4',5'-c']dithiophene-4,8-dione))] (PBDB-T) and 3,9-bis(6-methyl-2-methylene-(3-(1,1-dicyanomethylene)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3-d']-s-indaceno[1,2-b:5,6-b']dithiophene (IT-M). The BHJ layers were formed on a pre-patterned indium-tin oxide (ITO)-coated glass substrate by spin-coating using the blend solutions of PBDB-T and IT-M. The solar cell performances were investigated with respect to the cell position on the ITO-glass substrates. In addition, the short-term shelf lifetime of solar cells was tested by storing the PBDB-T:IT-M solar cells in a glovebox filled with inert gas. The results showed that the performance of solar cells was relatively higher for the cells close to the center of substrates, which was maintained even after storage for 24 h. In particular, the PCE of PBDB-T:IT-M solar cells was marginally decreased after storage for 24 h owing to the slightly reduced fill factor, even though the open circuit voltage was unchanged after 24 h.

• Clinical and Experimental Reproductive Medicine
• /
• v.49 no.2
• /
• pp.149-158
• /
• 2022

Objective: Optimizing culture media for the incubation of immature oocytes is a vital strategy to increase the oocyte maturation rate during in vitro maturation (IVM) programs. This study evaluated the IVM and fertilization rates of human germinal vesicle (GV) and metaphase I (MI) oocytes using two different maturation media (commercial and homemade) with or without growth differentiation factor 9-β (GDF9-β). supplementation. Methods: Immature oocytes from intracytoplasmic sperm injection (ICSI) cycles were collected and assigned to one of two IVM culture media (commercial or homemade; cleavage-stage base). After maturation, MII oocytes were examined under an inverted microscope for the presence of the polar body, zona pellucida (ZP) birefringence, and meiotic spindle (MS) visualization after maturation in four conditions (commercial or homemade medium, with or without GDF9-β. ICSI was done for matured oocytes, and fertilization was confirmed by the visualization of two distinct pronuclei and two polar bodies. Results: No significant differences were found between the two culture media in terms of the time and rate of oocyte maturation or the rate of fertilization (p>0.05). Growth factor supplementation increased the 24-hour maturation rate for both GV and MI oocytes only in homemade medium. The maturation rate after 24 hours was higher for MI oocytes (p<0.05). Similar results were observed for MS visualization and ZP structure in both types of media (p>0.05). Conclusion: Higher rates of oocyte maturation and fertilization were observed after application of homemade medium supplemented with GDF9-β. Therefore, this combination may be recommended as an alternative for clinical IVM programs.

• Asia-Pacific Journal of Business
• /
• v.12 no.4
• /
• pp.289-297
• /
• 2021

Purpose - This study analyzed the correlation between economic liberalization and foreign direct investment. The purpose of this study is to seek ways to attract foreign direct investment from developing countries. Design/methodology/approach - This study analysed with observations of 19 from 2000 to 2018 using a fixed effect model, a random effect model, and a two-way fixed effect model. Findings - First, it was found that economic liberalization had a positive effect on attracting foreign direct investment in the early stages of economic liberalization. Second, it was found that economic liberalization in the deepening stage of economic liberalization had a negative effect on attracting foreign direct investment. In general, it was found that the higher the level of economic liberalization in developing countries is not accompanied by innovative changes in the industrial structure, the higher the level of economic liberalization is likely to decrease the inducement of foreign direct investment due to negative factors such as an increase in labor costs. Overall, this study approved that Economic liberalization have a non-linear (inverted U-shape) relationship with the inflow of foreign direct investment. Research implications or Originality - First, this study attempted to expand the variables for the determinants of FDI by analyzing economic factors which is a determinent of FDI. Second, economic liberalization generally has a positive effect on foreign direct investment, but it proved that it does not have only positive effects as a factor of attracting foreign direct investment in developing countries. The advantage of low wages in ASEAN countries acts as a factor for foreign direct investment, but as the degree of economic liberalization increases, the environment such as government size, guarantee of property rights, international trade freedom, fiscal soundness, and regulations change positively. On the other hand, it can be suggested that if the industrial level is less, it may lead to a loss of comparative advantage and a decrease in investment.

• Environmental and Resource Economics Review
• /
• v.31 no.4
• /
• pp.887-908
• /
• 2022

In order to confirm the effects of economic growth and environmental improvement, this study analyzed the existence of environmental Kuznets curve (EKC) for SO₂ emission, greenhouse gas emission, and waste generation in OECD countries. As a result of panel analysis, the shape of the EKC were different depending on environmental pollutants. SO₂ generated peaks relatively early in economic growth, and the peak of greenhouse gas emissions was showed in higher income level. But both emissions showed the a complete inverted U-shaped curve decreasing after the peak. On the other hand, for waste, there was no environmental Kuznets curve that could confirm the peak. Therefore, this study confirmed that it is difficult to expect a voluntary reduction in all environmental pollutants, and additional global joint efforts are needed to pass the peak. In particular, since waste has a greater impact on population density and industrial structure than income level, additional policy efforts are needed to reduce generation and create a resource circulation system.

• Architectural research
• /
• v.25 no.1
• /
• pp.1-9
• /
• 2023

Structural ageing influences the structural performance in a negative way by reducing the seismic resilience of the structure which makes it a major concern around the world. Retrofitting is considered to be a pragmatic and feasible solution to address this issue. Numerous retrofitting techniques are devised by researchers over the years. The viability of using steel bracings as retrofitting component is evaluated on a G+30 storied building model designed according to ACI318-14 and ASCE 7-16. Four different types of steel bracing arrangements (V, Inverted V/ Chevron, Cross/ X, Diagonal) are assessed in the model developed in commercial nu-merical analysis software while considering both material and geometric nonlinearities. Reducing displacement and cost in the structures indicates that the design is safe and economical. Therefore, the purpose of this article is to find the best bracing system that causes minimum displacement, which indicates maximum lateral stiffness. To evaluate the seismic vulnerability of each system, incremental dynamic analysis was conducted to develop fragility curves, followed by the formation of collapse margin ratio (CMR) as stipulated in FEMA P695 and finally, a cost estimation was made for each system. The outcomes revealed that the effects of ge-ometric nonlinearity tend to evoke hazardous consequences if not considered in the structural design. Probabilistic seismic and economic probes indicated the superior performance of V braced frame system and its competency to be a germane technique for retrofitting.