• Nuclear Engineering and Technology
• /
• 제52권6호
• /
• pp.1243-1251
• /
• 2020

Irradiation-induced damage of binderless nanoporous-isotropic graphite (NPIG) prepared by isostatic pressing of mesophase carbon microspheres for molten salt reactor was investigated by 3.0 MeV He⁺ irradiation at room temperature and high temperature of 600 ℃, and IG-110 was used as the comparation. SEM, TEM, X-ray diffraction and Raman spectrum are used to characterize the irradiation effect and the influence of temperature on graphite radiation damage. After irradiation at room temperature, the surface morphology is rougher, the increase of defect clusters makes atom flour bend, the layer spacing increases, and the catalytic graphitization phenomenon of NPIG is observed. However, the density of defects in high temperature environment decreases and other changes are not obvious. Mechanical properties also change due to changes in defects. In addition, SEM and Raman spectra of the cross section show that cracks appear in the depth range of the maximum irradiation dose, and the defect density increases with the increase of irradiation dose.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.212-215
• /
• 2002

Interfacial evaluation and damage sensing of the carbon fiber/epoxy-amine terminated (AT)-polyetherimide (PEI) composites were performed using micromechanical test and electrical resistance measurement. As AT-PEI content increased, the fracture toughness of epoxy-AT-PEI matrix increased, and thus their interfacial shear strength (IFSS) was improved due to the improved toughness. After curing process, the changes in electrical resistance (ΔR) with increasing AT-PEI contents increased gradually because of the changes in thermal expansion coefficient (TEC) and thermal shrinkage of matrix. Matrix fracture toughness was correlated to the IFSS, residual stress and electrical resistance. The results obtained from the electrical resistance measurement during curing process, reversible stress/strain, and durability test were consistent with modified matrix toughness properties.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.18-21
• /
• 2003

A behavior of interface of cold forging tool coated by hard film is analyzed by FEM. The indentation of a hemispherical tool of SUJ2 in JIS coated by electroplated coating of chromium into a cylindrical workpiece of S25C in JIS is performed. The proposed constitutive equations are implemented by the non-linear springs model at the interface. Calculated results show that the maximum interfacial normal displacement is observed at an immediately forward from the lip of the indentation, whereas maximum interfacial tangential displacement is at the immediately backward of the lip of the indentation.

• Advances in materials Research
• /
• 제8권3호
• /
• pp.197-217
• /
• 2019

In this study, the interfacial stresses in RC beams strengthened by externally bonded prestressed GFRP laminate are evaluated using an analytical approach, based on the equilibrium equations and boundary conditions. A comparison of the interfacial stresses obtained from the present analytical model and other existing models is undertaken. Otherwise, a parametric study is conducted to investigate the effects of geometrical and material properties on the variation of interfacial stresses in damaged RC beams strengthened by externally bonded prestressed GFRP laminate. The results obtained indicate that the damage degree has little effect on the maximum shear stress, with a variation less than 5% between the damaged and undamaged RC beams. However, the results also reveal that the prestressing level has a significant effect on the interfacial stresses; hence the damaged RC beam strengthened with an initial prestressing force of 100 kN gives 110% higher maximum shear stress than the damaged RC beam strengthened with an initial prestressing force of 50 kN. The values of shear stress obtained by the analytical approach are approximately equal to 44% of those obtained from the numerical solution, while the interfacial normal stresses predicted by the numerical study are approximately 26% higher than those calculated by the analytical solution.

• 한국건설순환자원학회논문집
• /
• 제11권1호
• /
• pp.79-88
• /
• 2023

본 연구에서는 철근 부식에 의한 콘크리트 단면의 구조적 거동을 정량화하기 위해 철근 표면에 형성되는 녹을 모델링했으며, 변수로는 철근과 콘크리트 사이의 계면 공극, 피복두께, 철근 직경을 취했다. 철근 부식시 구조적 한계에 가장 큰 영향을 미치는 인자는 계면의 공극크기였으며, 철근 직경, 피복두께 순으로 나타났다. 피복두께 75 mm, 철근직경 20 mm의 콘크리트 단면에서 계면의 공극이 1 ㎛에서 10 ㎛로 증가되면, 균열을 유발시키는 철근 부식량은 16.95 ㎛에서 27.69 ㎛로 크게 증가 되었다. 또한 철근 표면에 형성된 녹이 계면의 공극을 다 채우기 전까지 콘크리트 단면에는 손상이 발생되지 않았으며, 계면공극 범위를 넘어서는 양의 녹이 철근 표면에 형성된 후 콘크리트 단면은 항복, 균열 및 파단 상태에 이르렀다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.141-144
• /
• 2005

Sensing and interfacial evaluation of Ni nanowire strands/polymer composites were investigated using Electro-micromechanical technique. Electro-micromechanical techniques can be used as sensing method for micro damage, loading, temperature of interfacial properties. Using Ni nanowire strands/silicone composites with different content, load sensing response of electrical contact resistivity was investigated under tensile and compression condition. The mechanical properties of Ni nanowire strands with different type/epoxy composites were measured using uniformed cyclic loading and tensile test. Ni nanowire strands/epoxy composites showed humidity and temperature sensing within limited ranges, 20 vol% reinforcement. Some new information on temperature and humidity sensing plus loading sensing of Ni nanowire strands/polymer composites could be obtained from the electrical resistance measurement as a new concept of the nondestructive interfacial evaluation.

• 대한토목학회논문집
• /
• 제28권1A호
• /
• pp.115-123
• /
• 2008

최근 섬유강화 복합재료의 특성예측은 많은 공학자들에게 관심의 대상이 되고 있으며, 섬유강화 복합재료의 특성을 예측하기 위한 다양한 이론적, 수치적 방법들이 제안되고 있다. 본 연구에서는 복합재료내 구성요소를 고려한 Ju and Zhang (2001)의 미세역학 모델을 개선하고 원형섬유와 매트릭스간의 점진적인 손상을 고려하여 원형섬유강화 복합재료의 탄소성거동 및 점진적 손상해석을 위한 미세역학 모델을 개발하였다. 제안된 해석모델을 이용하여 다양한 수치해석을 통해 원형섬유강화 복합재료의 탄소성거동 및 점진적 손상을 예측하였고 손상을 고려하지 않은 모델과의 비교를 통하여 점진적 손상이 복합재료의 탄소성거동에 미치는 영향을 검토하였다.

• 한국진공학회지
• /
• 제2권4호
• /
• pp.468-473
• /
• 1993

Damages on Si substrate induced by Ar ion implantation and it annealing behavior during rapid thermal annealing were investigated by the cross-sectional TEM (transmissin electron microscopy), RB(Rutherfordbackscattering) spectra an dthermal wave (TW) modulation reflectance methods. Continuous amorphous layer extending to the surface were generated by Ar ion implantation for higher doses than 1 $\times$1015cm-2. The recrystallization of the amorphous layer prodeeded as the annealing temperature increased . However the amorphous /crystal interfacial undulations caused the micro twins and damage clusters. Damage clusters generated by lower doses than 1 $\times$1015 cm-2 disappeared slowly as the annealing temperature increased, but even at 110$0^{\circ}C$ a few damage clusters still remained.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.261-264
• /
• 2002

Interfacial evaluation, damage sensing and cure monitoring of single carbon fiber/thermosetting composite with different curing processes was investigated using electro-micromechanical test. After curing, residual stress was monitored by measurement of electrical resistance (ER) and then it was compared to correlate with various curing processes. In thermal curing, curing shrinkage appeared significantly by matrix shrinkage and residual stress due to the difference in thermal expansion coefficient (TEC). The change in electrical resistance (ΔR) on thermal curing was higher than that on ultraviolet (UV) curing. For thermal curing, apparent modulus was the highest and reaching time until same strain was faster. So far thermal curing shows strong durability on the IFSS after boiling test.

• Structural Engineering and Mechanics
• /
• 제86권5호
• /
• pp.663-671
• /
• 2023

Freeze-thaw cycles induce strength loss at the frozen soil-concrete interface and deterioration of bonding, which causes construction engineering problems. To clarify the deterioration characteristics of the interface under the freeze-thaw cycle, a frozen soil-concrete sample was used as the research object, an interface scanning electron microscope test under the freeze-thaw cycle was carried out to identify the micro index information, and an interface shear test was carried out to explore the loss law of interface shear strength under the freeze-thaw cycle. The results showed that the integrity of the interface was destroyed, and the pore number and pore size of the interface increased significantly with the number of freeze-thaw cycles. The connection form gradually deteriorates from surface-to-surface contact to point-to-surface contact and point-to-point contact, and the interfacial shear strength decreases the most at 0-3 freeze-thaw cycles, with small decreases from to 3-8 cycles. After 12 freeze-thaw cycles, the interfacial shear strength tends to be stable, and shear the failure occurs internally in the soil.