• 한국전자파학회논문지
• /
• 제21권3호
• /
• pp.262-268
• /
• 2010

본 논문에서, 부성 저항 특성을 갖는 능동 커패시턴스 회로를 이용한 고출력 능동 가변 대역 통과 여파기는 동축형 유전체 공진기와 버랙터 다이오드를 사용하여 설계하였으며, 셀룰러 TX, RX 대역을 모두 가변할 수 있도록 설계하였다. 능동 커패시턴스 회로의 직렬 피드백 구조는 가변 대역 통과 여파기의 버랙터 다이오드로부터 생기는 손실을 보상함과 동시에 고출력 특성을 갖도록 하기 위해 $P_{1dB}$가 32 dBm인 GaAs HFET을 사용하였다. 버랙터 다이오드는 고선형 특성을 갖도록 하기 위해 back-to-back 구조를 사용하였다. 제작된 2단 능동 가변 대역 통과 여파기는 셀룰러 대역인 800 MHz에서 900 MHz를 가변하며, 각각 25 MHz 대역폭으로 TX 대역 836 MHz에서 0.48 dB 삽입 손실 특성을 나타냈으며, RX 대역 881.5 MHz에서 0.39 dB 삽입 손실 특성을 나타내었다. $P_{1dB}$특성은 TX 및 RX 대역에서 각각 19.5 dBm과 23 dBm을 얻었다.

• Journal of Astronomy and Space Sciences
• /
• 제28권3호
• /
• pp.203-216
• /
• 2011

To prepare for a future Korean lunar orbiter mission, semi-optimal lunar capture orbits using finite thrust are designed and analyzed. Finite burn delta-V losses during lunar capture sequence are also analyzed by comparing those with values derived with impulsive thrusts in previous research. To design a hypothetical lunar capture sequence, two different intermediate capture orbits having orbital periods of about 12 hours and 3.5 hours are assumed, and final mission operation orbit around the Moon is assumed to be 100 km altitude with 90 degree of inclination. For the performance of the on-board thruster, three different performances (150 N with $I_{sp}$ of 200 seconds, 300 N with $I_{sp}$ of 250 seconds, 450 N with $I_{sp}$ of 300 seconds) are assumed, to provide a broad range of estimates of delta-V losses. As expected, it is found that the finite burn-arc sweeps almost symmetric orbital portions with respect to the perilune vector to minimize the delta-Vs required to achieve the final orbit. In addition, a difference of up to about 2% delta-V can occur during the lunar capture sequences with the use of assumed engine configurations, compared to scenarios with impulsive thrust. However, these delta-V losses will differ for every assumed lunar explorer's on-board thrust capability. Therefore, at the early stage of mission planning, careful consideration must be made while estimating mission budgets, particularly if the preliminary mission studies were assumed using impulsive thrust. The results provided in this paper are expected to lead to further progress in the design field of Korea's lunar orbiter mission, particularly the lunar capture sequences using finite thrust.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1852-1854
• /
• 1999

In order to enhance satellite communication system performance, filters are required with the characteristics of sharp skirt, low insertion loss, and high power handling capability. But the performance of microwave passive filters is significantly declined by the conduction losses, especially in case of planar structures using film conductors. By using high temperature superconducting(HTS) film material as the conductor, higher performance could be expected. We have designed and developed narrow bandpass filters using haripin-type superconducting microstrip line for satellite communication. High quality superconducting YBCO thin films have been grown on MgO substrates by pulsed laser deposition(PLD) The deposited YBCO films were patterned by conventional wet-etching process. The transition temperatures of these films had shown 86 - 89 K. The film thicknesses were about 500 nm. Experimental results are presented for the insertion loss and return loss of the filter at 60 K.

• 한국소음진동공학회논문집
• /
• 제16권9호
• /
• pp.949-957
• /
• 2006

In this Paper, reduction of noise and vibration in ship cabins by using floating floor is studied. Two theoretical models are presented and predicted insertion losses of floating floor are compared to experimental results, where measurements have been done in mock-up built for simulating typical ship cabin structures. In ships, mineral wool is usually used as the impact absorbing materials. The first model (M-S-Plate Model) is that upper plate and mineral wool are assumed as a one-dimensional mass-spring system, which is in turn attached to the simply supported elastic floor. The second model (Wave-Plate Model) is that mineral wool is assumed as an elastic medium for wave propagation. The comparisons show that M-S-Plate model is in good agreement with experimental results when density of mineral wool is 140K, and fiber direction is horizontal. For higher density and vertical fiber direction, Wave-Plate model shows good agreements with measurements. It is found that including the elastic behavior of the floor is essential in improving accuracy of the prediction for low frequency ranges below $100{sim}200Hz$.

• 한국전자파학회논문지
• /
• 제14권8호
• /
• pp.878-883
• /
• 2003

본 논문에서는 평판형 마이크로스트립 공진기를 위한 선형 및 지수형 테이퍼 라인을 이용한 급전선 구조를 제안하였다. 제안된 테이퍼 급전선(Tapered Feedline: TFL)은 결합 효율 증가에 의해 공진기 설계시 발생하는 결합 손실과 임피던스 부정합의 문제를 해결하였다. 제안된 구조의 급전각에 따른 삽입 손실 및 대역폭 변화에 대한 특성이 평가되었으며, ${\lambda}_{g}$/2의 최적 급전선 길이가 제시되었다. 제안된 테이퍼 급전선 구조를 마이크로스트립 링 공진기/여파기와 패치 안테나에 적용하였으며, 공진기/여파기 구조에서는 약 7 dB의 삽입 손실 이득을 얻었으며, 패치 안테나에서는 우수한 정합 특성과 왜곡 없는 방사 패턴 등을 나타내었다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권8호
• /
• pp.319-324
• /
• 2003

AIN thin films are deposited on Si (100) and $SiO_2$/Si substrates by using an RF magnetron sputtering method and by changing the conditions of deposition variables, such as RF power, $N_2$/Ar flow ratio, and substrate temperature ($T_sub$). For all the deposited AIN films, XRD Peak patterns are monitored to examine the effect of deposition condition on the crystal orientation. Highly (002)-oriented AIN films are obtained at following nominal deposition conditions; RF Power : 350W, $N_2$/Ar ratio = 10/20, T$_{sub}$ : $250^{\circ}C$, and working pressure = 5mTorr, respectively. AIN-based SAW devices are fabricated using a lift-off method by varying the thickness of AIN layer. Insertion losses and side-lobe rejection levels of fabricated SAW devices are extracted from their frequency response characteristics, which are also compared in terms of AIN thickness and substrate. Relationships between the film properties of AIN films and the frequency responses of SAW devices are discussed. It is concluded from the experimental results that the (002)-preferred orientation as well as the surface roughness of AIN film may play a crucial role of determining the device performances of AIN-SAW devices.s.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.56-59
• /
• 1997

SAW filters of transversal type were fabricated on some piezoelectric substrates of the LN 128$^{\circ}$ Y-X, LN 64$^{\circ}$Y-X, Quartz ST-cut wafers through the simulation in which the number o: IDT and window function were changed for the required frequency, and the mask making. Their IDT spacing and width were 3 ${\mu}{\textrm}{m}$, chip size was 4.462 $\times$ 2.086 mm$^2$, and they had double electrode transversal type IDTs. In addition to pure Al electrode devices, Ti thin films having the different thicknesses was introduced between the Al electrode and the substrate for improving the power resistance strength. They had 11-12 dB insertion losses similar to those of pure Al electrode SAW filters in case of LN 128$^{\circ}$ Y-X, LN 64$^{\circ}$ Y-X, meaning that Ti thin film was not detrimental to the insertion loss and general frequency properties. The filters had the center frequencies 162MHz for LN 128$^{\circ}$ Y-X, 186MHz for 64$^{\circ}$ Y-X, and 131MHz for Quartz ST-cut substrates.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.644-647
• /
• 2004

Optical add/drop multiplexers (OADMs), one of the new network elements, will play a key role enabling greater connectivity and flexibility in the dense wavelength-division multiplexing (DWDM) networks. The importance of OADMs is that they allow the optical network to be local transmitting/extraction on a wavelength-by-wavelength basis to optimize traffic, efficient network utilization, network growth, and to enhance network flexibility. Also, the automatic assembly system of micro optical filters and fibers is a key technology in the development of optical modules with high functionality. Recently, one of remarkable tends in the development of optical communication industry is the miniaturization and integration of products. In this research, we have developed a system capable of automatic alignment of a film filter and a lensed fiber in order to improve the speed and losses in the optical fiber to filter alignment of optical modules. Using the developed automatic alignment system and silicon optical benches, we have fabricated the micro OADM and measured the insertion loss and aging effect.

• 한국정밀공학회지
• /
• 제12권5호
• /
• pp.126-135
• /
• 1995

An exhaust muffler is one of the simple and effective means to meet the demand for a quiet vehicle, and it deserves a close attention to effectively reduce the engine noise. The transfer function technique is one of the tools that have been used to analyze the noise characteristics of the exhaust muffler. In this paper we obtained a transfer function using the forward-going and backward-going components of sound pressure in the exhaust muffler, which is compatible wiht lattice filter algorithm. This form of transfer function is obtained for the basic elements of a muffler, such as uniform tube, open termin- ation, closed termination, anechoic termination, expansion, contraction, extended-tube resonator, hole, Helmholtz resonator, and concentric hole-cavity resonator. The results are combined to produce the transfer function of various types of mufflers. With this transfer function we calculate the transmission and insertion losses of mufflers, and examined the effects of various design parameters. Comparisons were made between the calculation and experimental results, which showed a good agreement, and we conclude that the transfer function of lattice form can be used to analyze the noise characteristics of the exhaust mufflers.

• 한국ITS학회 논문지
• /
• 제7권6호
• /
• pp.31-37
• /
• 2008

지능형 교통정보 시스템을 구성하기 위한 통신장비로 위성 및 무선 통신 시스템은 광범위한 도로에서 수집되는 정보를 전달하기 위해 광대역 특성이 요구된다. 이러한 통신 시스템에 사용되는 여파기 또한 광대역 대역통과 여파기가 요구되며, 본 논문에서는 이러한 통신 시스템에서 사용이 가능한 광대역 대역통과 여파기를 설계하였다. 설계된 대역통과 여파기는 지금까지 광대역 구현이 어려웠던 평행결합선로의 대역통과 여파기로서 이 여파기를 광대역 및 소형화로 실현 가능하도록 설계하였다. 설계된 여파기는 중심 주파수 5.8 GHz에서 대역폭 60%, 삽입손실과 반사손실은 각각 0.4 dB, 17.4 dB의 결과 값을 얻었다.