• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.6
• /
• pp.628-633
• /
• 2014

This paper proposes a performance improvement method of the conventional double talk detection method which can operate before convergence of the echo canceller. The proposed method estimates the coefficients of the linear predictive coding(LPC) filter by using the primary input signal. The time-varying threshold for double talk detection is determined based on the LPC filter gain of the primary input signal level. The proposed method can reduce not only false detection rate which means wrong detection of single talk as double talk but also double talk detection delay. Computer simulation was performed using a long-term real speech signals. It is shown that the proposed method improves the conventional method in terms of lowering the false detection rate and shortening the detection delay.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.47-52
• /
• 2017

In this paper, CMOS SAR A/D converter 1.8V supply for the design of an A/D converter having an middle speed for the biological signal processing was designed. This paper proposes design of a 10-bit SAR Analog to Digital Converter improving linearity driven by MSB node of C-DAC array divided into 4 equal parts. It enhances linearity property, by retaining the analog input signal charging time at MSB node. Because MSB node samples analog input, it enhances resolution through getting initial input signal precisely. By using split capacitor on C-DAC array, it reduced chip size and power dissipation. The Proposed SAR A/D Converter is fabricated in 0.18um CMOS and measured 7.5 bits of ENOB at sampling frequency 4MS/s and power supply of 1.8V. It occupies a core area of $850{\times}650um^2$ and consumes 123.105uW. Therefore it results in 170.016fJ/step of FOM(Figure of Merit).

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.2
• /
• pp.5-9
• /
• 1997

In this paper, when we use the chirp signal as input signal of ultrasonic signal system the technique for determining the bandwidth of the chirp signal that maximizes the amplitude of the compressed ultrasonic echo signal has been studied. In ultrasonic signal processing systems, the signal-to-noise ratio of the echo signal can be too low due to damping and scattering of the ultrasonic wave during transmission. Method of pulse compression using chirp signal is a means to increase the signal-to-noise ratio in ultrasonic pulse-echo systems. Simulation and experimental results showed that the output signal of ultrasonic system was increased by pulse width of chirp signal and the optimum-bandwidth of the chirp signal was 1.15 times larger than the bandwidth of the ultrasonic system.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.652-657
• /
• 1992

This paper presents to accomplish successfully a multi-input real time control by applying control hierarchy for sliding mode of multi-joint manipulators whose nonlinear terms are regarded as disturbances. We- could simplify the dynamic equations of a manipulator and servo system, which are composed of linear elements and nonlinear elements, by assuming that nonlinear terms, which are Inertia term, gravity force term, Coriolis force term and centrifugal force term, are external disturbance. By simplifying that equation, we could easily obtain a control input which satisfy sliding mode of multi-input system. We proposed a new control input algorithm in order to decrease chattering by changing control input according as effect of disturbance if a control response become within allowance error range. In this experiments, we used DSP(Digital Signal Processor) controller to suppress chattering by time delay of calculation and to carry out real time control.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1577-1582
• /
• 2013

In this paper, we have analyzed the performance of MIMO (Multi-Input Multi-Output) underwater acoustic communication by using the acquired data via the experiments in water tank. First of all, in the pursuit of this aim, we have measured the channel transfer characteristics at several transceiver locations. The transmitted signal was modulated by QPSK(Quadrature Phase Shit Keying) and the received signal was recovered through the detector that contains the zero forcing equalizer. A maximum 30~40 ms delay was appeared because of physically closed water tank environment that has the harsh multi-path transmission conditions. In result of experiment, even though the bit error rate showed comparatively large when $2{\times}2$ MIMO system with two transmitters and receivers was considered. However, we confirmed it has approximately 15% enhanced performance compared with SISO (Single-Input Single-Output) system.

• Journal of Internet of Things and Convergence
• /
• v.9 no.2
• /
• pp.71-76
• /
• 2023

In this paper, we propose a smoothed received signal strength indicator (RSSI)-based distance estimation using deep neural network (DNN) for accurate distance estimation in an environment where a single receiver is used. The proposed scheme performs a data preprocessing consisting of data splitting, missing value imputation, and smoothing steps to improve distance estimation accuracy, thereby deriving the smoothed RSSI values. The derived smoothed RSSI values are used as input data of the Multi-Input Single-Output (MISO) DNN model, and are finally returned as an estimated distance in the output layer through input layer and hidden layer. To verify the superiority of the proposed scheme, we compared the performance of the proposed scheme with that of the linear regression-based distance estimation scheme. As a result, the proposed scheme showed 29.09% higher distance estimation accuracy than the linear regression-based distance estimation scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1867-1870
• /
• 2003

The analysis and simulation are the method to study the behavior, response, and specification of the driver device. This paper proposes brushless DC drive which using the vector control technique. The encoder is used detect the rotor position and decode to Three-phase step signal. The step signal is modulated with triangle signal and change to the pulse width modulation (PWM) signal. The PWM signal is used for control the input power of the motor based on the vector control technique. The experimental results of the driver circuit and motor response performed under the following condition: as the motor was started, change the load torque, and vary the supply voltage. The experimental performs with a dynamometer and the test results are compared to the simulation method is the same result.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.229-231
• /
• 2016

A 180-GHz signal source based on a 65-nm CMOS technology has been developed in this study. The 180-GHz signal source consists of a 90-GHz fundamental-mode Colpitts oscillator and a 180-GHz frequency doubler. A coupled-line is employed to couple two oscillator cores for generating a differential signal, which is delivered to the input of the differential-mode doubler. The fabricated signal source operates from 181.2 to 182.4 GHz with output power varying from -15.3 to -10.8 dBm. The peak output power was -10.53 dBm at 181.3 GHz with a DC power consumption of 42 mW, and the associated phase noise was -71 dBc/Hz at 1 MHz offset.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.1
• /
• pp.131-138
• /
• 2014

This paper is on a stereo acoustic echo canceller with the blind signal separation for post processing. The convergence speed of the stereo acoustic echo canceller is deteriorated due to mixing two residual signals which are update signals of each echo canceller. To solve this problem, we are to use the blind signal separation(BSS) method separating the mixed signals after the echo cancellers. The blind signal separation method can extracts the source signals by means of the iterative computations with two input signals. We had verified performances of the proposed acoustic echo canceller for stereo through simulations. The results of simulations show that the acoustic echo canceller for stereo using this algorithm operates stably without divergence in the normal state. And, when the speech signals were inputted, this echo canceller achieved about 2dB higher ERLE with the BSS post processing method than without this method. This stereo echo canceller showed the best performance in the case of inputting the real voice signal.

• Journal of Integrative Natural Science
• /
• v.13 no.2
• /
• pp.69-75
• /
• 2020

Multiple Input Multiple Output (MIMO) is one of the important wireless communication technologies. This paper proposes MIMO system capacity enhancement by using convolution of periodic circulating vector signals. This signal represents statistical dependencies between transmission signal with discrete noise and receiver signal with the linear shifting of MIMO channel capacity by positive extents. We examine the channel capacity, outage probability and SNR of MIMO receiver by adding log determinant signal with validated in terms of numerical simulation.