• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.229-230
• /
• 2006

The global metal injection moulding industry is getting mature. The technology is on its way to grow from a niche technology to a widely accepted manufacturing process. This paper addresses the latest technological trends in MIM. Challenges in materials development as well as the current limits of the technology are discussed. Trends in processing like 2-component injection moulding and micro injection moulding are presented. The European MIM market situation is described and some key factors for business success are addressed. In the discussion of future business opportunities best practice examples are included.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.3
• /
• pp.192-200
• /
• 2002

There is a volume change between the sediments and the dredged materials because the dredged materials is fully disturbed by the dredger and settled in the basin from the stabilized condition. The volume of the dredged materials is also affected by the coagulants and flocculants (hereafter C & F) which was used to speed up the settling of the suspended solids. In this study, the volume change of the dredged materials is analysed in detail due to the injection amount of the C & F. The dredged materials were sampled in the lagoon located in the East coastal zone, and the volume change of the samples is quantitatively analysed by the laboratory test due to the change of the clay content and the amount of the C & F. The optimal amounts of the C & F is determined by showing the minimal volume change due to C & F injection. From the experimental results, the volume of the dredged materials is increased 1.68 times on an average and the volume change rate is slightly increased, i.e., negligible, as the clay content increase in the case of the C & F injection.

• Journal of Adhesion and Interface
• /
• v.17 no.1
• /
• pp.15-20
• /
• 2016

Fiber arrangement was important for fiber reinforced thermoplastic composites using injection fabrication. In this work, fiber arrangement in CF/PP was investigated to use electrical resistance (ER) method during injection times. There were 3 types of injection products of CF/PP with different ER change ratio by fiber arrangement. High ER change ratio case of injection CF/PP products had better increased tensile strength. This reason was due to the fiber arrangement of CF/PP by injection. Fractured surface and contact angle of CF/PP products were used to evaluate for injection product quality. Uniform fiber arrangement of CF/PP by injection type exhibited the uniform heat condition of melted CF/PP. Steady thermal transfer effect occurred from melted CF/PP to steel injection mold. Steady thermal transfer effect of CF/PP was transmitted to high ER change ratio of mold. Ultimately, good condition CF/PP product by injection molding method could be predicted by using ER method.

• Journal of Environmental Health Sciences
• /
• v.32 no.5 s.92
• /
• pp.499-505
• /
• 2006

Bioventing efficiency was compared in a continuous and an intermittent(6hr injection and 6hr rest) air injection mode. Two lab-scale columns which packed with 5 kg of soil artificially contaminated by diesel oil were operated. The columns were maintained at the $25^{\circ}C{\pm}2.5$ in order to minimize the effect of exterior temperature variation. The flow rate of air injection mode were maintained constantly at the flow rate of 10 ml/min. The moisture of the columns was stably maintained at $60{\sim}80%$ of field capacity. The nutrient compounds were added to make C:N:P ratio as 100:10:l. The continuous and intermittent injection modes showed 67.56% and 69.63% reduction of initial TPH concentration during 90 days, respectively. Two venting modes showed similar results in the analysis of the trends of the hydrocarbon utilizing bacterial counts for operating periods. The carbon dioxide production rate of the continuous injection mode was higher than that of intermittent injection mode. The loss of diesel oil by volatilization in the continuous and intermittent injection modes were about 5% and 1%, respectively. The lower volatilization loss in the intermittent injection mode suggested that the biodegradation of TPH in the intermittent injection mode was greater than that of the continuous mode. These results suggested that the intermittent injection mode is more efficient than the continuous venting mode.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.529-530
• /
• 2006

• Korean Journal of Materials Research
• /
• v.14 no.11
• /
• pp.795-801
• /
• 2004

The injection molded Fe sintered bodies were fabricated using two kinds of Fe powders haying 50 nm and $3\sim5{\mu}m$ in diameter. In the using of Fe powder having 50 nm in diameter, the comparatively dense bodies ($94\sim97\%$) were obtained even at low sintering temperature ($600\sim700^{\circ}C$), while in the sintered bodies ($1000^{\circ}C$) using $3\sim5{\mu}m$ Fe powder, their relative densities showed low values about $93\%$, although they were strongly depend on the sintering temperature and volume ratio of Fe powder and binder. In the sintered bodies using of 50 nm Fe powders, the volume shrinkage and grain size increased as the sintering temperature increased, but the values of hardness decreased. In the sample sintered at $650^{\circ}C$, the values of relative density, volume shrinkage and grain size were $96\%,\;37\%\;and\;0.97{\mu}n$, respectively and the minimum value of wear depth was obtained due to combination of fine grain and comparatively high density.

• Archives of Plastic Surgery
• /
• v.38 no.1
• /
• pp.53-62
• /
• 2011

Purpose: Even though Augmentation rhinoplasty is very popular surgical procedure, it is not easy to obtain ideal materials for augmentation. Many different synthetic materials are used but frequent complications are seen such as infection, extrusion, deform, and dislocation. Autologous tissues were used for augmentation rhinoplasty. We used dermofat graft and fat injection in augmentation rhinoplasty minimizing these problems. Methods: From 2006 to 2009, we used autologous tissues in augmentation rhinoplasty in 40 patients, 20 patients with dermofat graft and other 20 patients were treated with fat injection only. Dermofats were harvested from sacral area. gluteal fold, groin and preexisting scar tissue. Dermofats were inserted with small stab wound and fat tissues were injected as Coleman's technique. The patients were followed up 6 months to 5 years. Results: Most of the patients were satisfied in shape and height the nose. Early complications such as hematoma, infection and seroma were not found. Secondary fat injection was performed in 3 patients (15%) of dermofat graft group instead of 7 patients (35%) of fat injection only group. Conclusion: We obtained satisfactory results in augmentation rhinoplasty with dermofat graft and fat injection. Secondary fat injections were more often in fat injection group than dermofat graft group. Dermofat graft and fat injection could be another alternative technique for augmentation rhinoplasty and fat injection could be a secondary adjunctive treatment for undercorrection due to absorption.

• The Journal of the Korea Contents Association
• /
• v.15 no.3
• /
• pp.265-271
• /
• 2015

This study is the analysis about materials (from 2012 to 2014) which was stored in the data made from the 397 infants subjects who were born in 2012, with the basis of the preventive injection management, public health care information system by using SPSS win 18.0 program. After we analyzed the present non-injection state and the non-injection reasons with the basis of each birth month, each vaccine, each injection period, we found out that 89 infants(22.4%) were the ones who were not computerized. Except the 20 infants-the ones having uncertain phone numbers and addresses, and computerization errors, 69 infants (17.4%) were the ones that didn't get injection. We guided protective injection to them by sending SMS text message and we could inject 39 infants (9.8%) of them. We could achieve the high 92.4% injection rate. we want this research to be used to try wipe out the infectious diseases in this district and be utilized as the basic materials of protective injection cost support and health care policies, etc.

• Design & Manufacturing
• /
• v.13 no.3
• /
• pp.35-40
• /
• 2019

As the consumer market in the cosmetic, vehicle manufacturing and aerospace industries grows, the demand for manufacturing industries using on injection mold technology. Also, such manufacturing technology of metal machining is expensive, and the shape is limited. Cosmetic cushion fact products are divided into outer relevant to the exterior of the product and inner containers containing the actual contents. In the case of the inner container, it needs to be combined with the upper and lower cases. As environmental regulations are strengthened internationally, the use of a large number of component parts can result in significant losses in recycling and economics. Therefore, this study aims to perform injection molding analysis through injection molding simulation to develop a cushion fact container that can be recycled through the unification of products and materials using polypropylene to cope with environmental regulations. In the case of injection molding conditions, Injection Time(sec): 4.5, Cooling Time(sec): 13, Resin Temperature($^{\circ}C$): 240, and Pressure(MPa): 30 were determined. The results of injection molding simulation according to the two design methods were compared with the sync mark which shows the problem of filling and injection molding.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.561-567
• /
• 2014

Precision injection mold is an essential element in order to manufacture small and precision plastic lenses used for phone camera. There are many critical factors to meet the requested specifications of high quality plastic lenses. One of the main issues to realize high quality is minimizing decenter value, which becomes more critical as pixel numbers increases. This study suggests the method to minimize decenter value by modifying ejecting structure of the mold. Decenter value of injection-molded lens decreased to 1 ${\mu}m$ level from 5 ${\mu}m$ by applying suggested ejecting method. Also, we also developed BIS (Built-in Sensor) based smart mold system, which has pressure and temperature sensors inside of the mold. Pressure and temperature profiles from cavities are obtained and can be used for deduction of optimal injection molding condition, filling imbalance evaluation, status monitoring of injection molding and prediction of lens quality.