• 한국농촌건축학회논문집
• /
• 제24권2호
• /
• pp.45-52
• /
• 2022

Of the 17,106 domestic reservoirs(as of December 2020), 14,611 are older than 50 years, and these old reservoirs will gradually increase over time. The injection grouting method is most applied to the reinforcement method of the aging reservoir. However, the injection grouting method is not accurate in uniformity and reinforced area. An laboratory model test was conducted to evaluate the applicability of the deep mixing method, which compensated for these shortcomings, as a reservoir reinforcement method. As a result of calculating the hydraulic conductiveity for each method through the model test results, the injection grouting method was calculated as a hydraulic conductiveity value that was about 7.5 times larger than that of the deep mixing method. As a result of measuring the water level change in the laboratory model test, it was found that the water level change decreased in the injection method and deep mixing method compared to the non-reinforcement method. In addition, deep mixing method showed a water level change of about 15% based on 40 hours compared to the injection method, indicating that the water-reducing effect was superior to that of the injection method.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1791-1801
• /
• 2016

This paper considers a carrier based signal injection method for use in the three shunt sensing inverter (TSSI) for sensorless motor control. It also analyzes the loss according to the injection axis of the voltage signal. To remove both the phase current and rotor position sensors, a sensorless method and a phase current reconstruction method can be simultaneously considered. However, an interaction between the two methods can be incurred when both methods inject voltage signals simultaneously. In this paper, a signal injection based sensorless method with the 120° OFF Discontinuous PWM (DPWM) is implemented in a TSSI to avoid this interaction problem. Since one leg does not have a switching event for one sampling period in the 120° OFF DPWM, the switching loss is altered according to the injection axis. The switching loss in the d-axis injection case can be up to 32% larger than that in the q-axis injection case. Other losses according to the injection axis are also analyzed.

• 한국자동차공학회논문집
• /
• 제13권1호
• /
• pp.28-35
• /
• 2005

Fuel injection rate of an injector is affected by various injection conditions such as injection duration, fuel temperature, injection pressure, and voltage in LPG liquid injection systems for either a port-fuel-injection(PFI) or a direct injection(DI) in a cylinder. Even fuel injection conditions are changed, the air-fuel ratio should be accurately controlled to educe exhaust emissions. In this study, correction factor for the fuel injection rate of an injector is derived from the density ratio and the pressure difference ratio. A voltage correction factor is researched from injection test results on an LPG liquid injection engine. A compensation method of the fuel injection rate is proposed for a fuel injection control system. The experimental results for the LPG liquid injection system in a SI-engine show that this system works well on experimental range of engine speed and load conditions. And the fuel injection rate is accurately controlled by the proposed compensation method.

• Architectural research
• /
• 제11권2호
• /
• pp.27-34
• /
• 2009

The purpose of this study is to investigate the problem of crack repair materials and methods in existing concrete structure and to propose the effective injection method on crack repair by packer type. The result of this study is as follows. It is investigated that the crack width in the inner matrix of concrete structure is decreased about 30-40% than that in the surface of the concrete structure. Also it is showed that the possibility which could be monolithic with injection part became higher if the injection part is installed near to surface of concrete on the punching method to vertical direction against crack area. The injection of repair material can be poured smoothly under about $10N/mm^2$ pressure on the condition that cracks are monolithic with injection part without dust by drill. The method which is effective injection for a repair material is the punching method in compliance with coredrill. But, the research continuously is necessary about minimum injection pressure.

• 한국건축시공학회지
• /
• 제6권2호
• /
• pp.91-98
• /
• 2006

The purpose of this study is to investigate the problem of crack repair materials and methods in existing concrete structure and to propose the effective injection method on crack repair by packer type. The result of this study is as follows. It is investigated that the crack width in the inner matrix of concrete structure is decreased about 30-40% than that in the sulfate of the concrete structure. Also it is showed that the possibility which could be monolithic with injection part became higher if the injection part if installed near to surface of concrete on the punching method to vertical direction against crack area. The injection of repair material can be poured smoothly under about $10N/mm^2$ pressure on the condition that cracks are monolithic with injection part without dust by drill. The effective method to pour the injection repair material is the punching method by coredrill but several research to minimize injection pressure should be continually.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.581-586
• /
• 2003

The objective of this study is to evaluate the injection performance of crack repair method in concrete structure. To improve the quality of the concrete structure caulking material was injected into the crack of building that were planned to be demolished and injection properties of various repair method were compared and assessed according to type of crack. Results from the test showed that when cracks and injection port were integrated and the injection port wasn't blocked repair material was able to be injected even below around 40㎏/㎠ pressure. Moreover, effective pressure each type of packer showed wide range varying from 200-400㎏/㎠. As for drill method for injection port, core drill method has shown to be more effective compared to the air pump method

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.123-133
• /
• 1995

An injection control valve(ICV) was designed to control the fuel flow between a common rail and an injector with two commercial solenoids. To improve the performance of ICV, the characteristic method was applied. With this method, the flow characteristics in the ICV and the injector were studied and the parameters which affect the injection characteristics were also studied. From this study, following results were obtained. The injection duration can be controlled and with modifications of the effective valve stroke of ICV, the injection quantity and duration can be reduced to desired amount. Also the injection quantity and pressure can be controlled by reducing the hole size of the injector without the variation of the injection duration. For some conditions, the desired injection characteristics can be obtained by the changes of the valve timing, the effective valve stroke, the open pressure of the injector and the hole size of the injector.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권2호
• /
• pp.175-182
• /
• 2002

The cement injection technology on the purpose of ground reinforcement and cut-off has been used in construction sites until now. However, recently it is applied to prevent leakage of underground structure. In this study, applicability of the back side waterproof grouting method was verified through performing field model tests and reviewing case histories. From the results of this study, injection shape of the back side waterproof grouting method was appeared to be root type, and waterproof effect by injection of cement grout material was excellent because grout material infiltrated into boundary between wall of structure and back side ground to be waterproof layer. Components influencing infiltration of injection material are type of soil and degree of compaction. For effective injection, injection pressure has to vary gradually from high pressure to low pessure and small quantity of injection material has to be injected for long times. Also, spacing of injection hole must be designed considering condition of back side ground, injection area, W/C ratio, the number of injection and injection pattern properly.

• 한국정보통신학회논문지
• /
• 제25권3호
• /
• pp.478-485
• /
• 2021

광 주입 잠금 반도체 레이저의 주입 매개 변수를 조절하여 광학적 복소 신호를 생성 할 수 있다. 그러므로 정확한 주입 매개 변수의 결정은 광학적 복소 신호 생성 기술에서의 핵심 요소이다. 기존의 주입 매개 변수의 추출 이론은 광 주입 잠금 반도체 레이저의 비율 방정식을 사용하며, 이는 locking map 기반의 보간법을 사용하기 때문에 정확한 주입 매개 변수의 추출에 한계가 있다. 이를 해결하기 위하여 비율 방정식의 새로운 해석법을 제안한다. 제안된 해석법은 비율 방정식을 광학적 복소 신호의 생성에 맞게 수정하여 주입 매개 변수를 직접적으로 도출하는 방법이며, 이를 통하여 보간법을 통한 복소 신호 생성 대비 103 배의 오차 감소를 달성하였다.

• 한국기계가공학회지
• /
• 제16권1호
• /
• pp.63-69
• /
• 2017

The golden section search method is widely used to optimize a single design variable in many fields due to its superior advantages of search. In this paper, a new direct search method is proposed by modifying the search structure of the golden section search method; thus, it can be adapted in the optimization of a single design variable for the injection molding process. This proposed method is applied to determine an optimal gate position for the injection molding of a bezel of an automated teller machine for minimizing the injection pressure. Thus, an optimal gate position where the injection pressure is decreased by 4.5 MPa to that of the initial position was obtained with a small number of simulations. It is anticipated that the current proposed search method can be utilized as a practical tool for optimizing single variables for injection molding design.