• 한국지반공학회논문집
• /
• 제19권6호
• /
• pp.285-298
• /
• 2003

본 연구에서는 경사판 시험기를 이용하여 매립지에 흔히 나타나는 토목섬유/토목섬유, 토목섬유/모래의 접촉 마찰특성을 평가하였다. 경사판 시험기는 연직응력이 낮은 상태에서의 전단 거동을 정확히 모사하는 시험기로 널리 알려져 있으며, 본 연구에서는 이 시험기를 이용하여 각 접촉면의 마찰각을 평가하는 동시에, 각 토목섬유에 유발되는 인장력도 측정하였다. 실험 결과, 연직응력의 크기, 토목섬유의 종류, 토목섬유의 흙의 구성에 따라 접촉면의 마찰각과 토목섬유에 유발되는 인장력이 각각 다르게 측정됨을 확인하였다. 한편, 본 연구에서는 모래/지오텍스타일/지오멤브레인, 즉 두개의 접촉면을 동시에 모사하는 실험을 실시하여, 지오멤브레인 상부에 위치하는 지오텍스타일로 인해 지오멤브레인에 유발되는 인장력이 감소함을 관찰하였다. 본 연구 결과는 동일한 접촉면을 대상으로 실시된 직접전단 시험 결과와 비교하였으며, 마지막으로 상자의 변위가 발생하기 시작하는 시점, 즉 각 접촉면의 한계 경사에서 토목섬유에 유발되는 인장력을 기존에 제안된 해석해와 비교하여, 해석해의 정확도와 설계시 적용 가능성에 대하여 고찰하였다.

• Geomechanics and Engineering
• /
• 제34권6호
• /
• pp.637-648
• /
• 2023

When an earth pressure balance (EPB) shield machine bores a tunnel in gravelly sand stratum, the excavated natural soil is normally transformed using foam and water to reduce cutter wear and the risk of direct muck squeezing out of the screw conveyor (i.e., muck spewing). Understanding the undrained shear behavior of conditioned soils under pressure is a potential perspective for optimizing the earth pressure balance shield tunnelling strategies. Owing to the unconventional properties of conditioned soil, a pressurized vane shear apparatus was utilized to investigate the undrained shear behavior of foam-conditioned gravelly sands under normal pressure. The results showed that the shear stress-displacement curves exhibited strain-softening behavior only when the initial void ratio (e₀) of the foam-conditioned sand was less than the maximum void ratio (e_max) of the unconditioned sand. The peak and residual strength increased with an increase in normal pressure and a decrease in foam injection ratio. A unique relation between the void ratio and the shear strength in the residual stage was observed in the e-ln(τ) space. When e₀ was greater than e_max, the fluid-like specimens had quite low strengths. Besides, the stick-slip behavior, characterized by the variation coefficient of measured shear stress in the residual stage, was more evident under lower pressure but it appeared to be independent of the foam injection. A comparison between the results of pressurized vane shear tests and those of slump tests indicated that the slump test has its limitations to characterize the chamber muck fluidity and build the optimal conditioning parameters.

• 소성∙가공
• /
• 제15권1호
• /
• pp.27-33
• /
• 2006

It is necessary to improve the pattern replication and birefringence in LGP(Light guide panel) for better optical performance. In the present paper, the effects of injection-compression and injection-press mode with normal injection mold on the distribution of transcription of pattern and birefringence were studied. It was found that the values of pattern replication was improved and the birefringence was reduced for the cases of low initial clamping force in injection-compression mode and for the cases of longer mold opening length in injection-press mode, repectively.

• Journal of Ship and Ocean Technology
• /
• 제2권1호
• /
• pp.42-57
• /
• 1998

Genetic Algorithm (GA) is applied to obtain optimal Inspection plan for fatigue deteriorating structures. The optimization problem is defined so as to minimize inspection cost in the 1ifs-time of the structure under the constraint that the increment of failure probability in each inspection interval is maintained below a target value. Optimization parameters are the inspection timing and the inspection quality. The inspection timing is selected from the discrete intervals such as one year, two years, three years, etc. The inspection quality is selected from the followings; no inspection, normal inspection, sampling inspection or precise inspection. The applicability of the proposed GA approach is demonstrated through the numerical calculations assuming a structure consisting of four member sets. Influences of the level of target failure probability, initial defect condition and stress increase due to plate thickness reduction caused by corrosion on inspection planning are discussed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.1-10
• /
• 2009

Based on recent studies, the side resistance of rock socketed drilled shafts was affected by unconfined compressive strength of rock, socket roughness, rock types and joints, and initial normal stress. Especially, the socket roughness was affected by rock types and joints, drilling methods, and diameters of pile. In this study, a new roughness measurement system (BKS-LRPS, Backyoung-KyungSung Laser Roughness Profiling System) usable in water was developed. Based on the laboratory model tests, an EMD (Effective Measurement Distances) according to various turbidity was proposed as EMD=$1149.2{\times}T^{-0.64}_b$.

• Nuclear Engineering and Technology
• /
• 제26권4호
• /
• pp.570-577
• /
• 1994

The loss of water in the carbon steel balls and water region of the end shield for CANDU 6 reactor could lead to significant temperature gradient through the end shield structure which amy result in the excessive deformation. With an assumed end shield drained scenario, the heat deposition rates were calculated through the end shield associated with the central fuel channel during full power operation as an initial step to thermal stress analysis. The drained case was compared with that of water present normal case in therms of heat deposition rater and the total heating throughout the end shield regions. The compared results show that the heat deposition and the total heating remain almost the same between the two cases. It was found that the change of volume integrated flux in the end shield regions due to the loss of water contribute a negligible effect on the heat deposition in this region.

• Geomechanics and Engineering
• /
• 제37권6호
• /
• pp.591-597
• /
• 2024

The purpose of this paper is to depict the effect of gravity on a nonlocal thermoelastic medium with initial stress. The Lord-Shulman and Green-Lindsay theories with fractional derivative order serve as the foundation for the formulation of the fundamental equations for the problem. To address the problem and acquire the exact expressions of physical fields, appropriate non-dimensional variables and normal mode analysis are used. MATLAB software is used for numerical calculations. The projected outcomes in the presence and absence of the gravitational field, along with a nonlocal parameter, are compared. Additional comparisons are made for various fractional derivative order values. It is evident that the variation of physical variables is significantly influenced by the fractional derivative order, nonlocal parameter and gravity field.

• 한국지반공학회논문집
• /
• 제22권7호
• /
• pp.23-35
• /
• 2006

본 연구에서는 암반에 근입된 현장타설말뚝의 주면하중전이특성을 분석하기 위하여, 주요 영향요소(일축압축강도, 거칠기, 수직강성, 초기구속응력, 재료성질)에 따라 일정수직강성(Constant Normal Stiffness, CNS)조건의 직접전단시험을 수행하였다. 그 결과 암반에 근입된 현장타설말뚝의 주변하중전이특성을 3구간으로 이상화할 수 있었으며, 각 구간에서의 거동을 지배하는 주요 요소의 영향 및 그에 따른 거동을 파악할 수 있었다. 이를 토대로 암반의 절리 및 풍화상태를 나타내는 GSI(Geological Strength Index)를 이용한 Hoek-Brown 파괴기준(1997)을 적용하여, 암반에 근입된 현장타설말뚝의 굴착면 거칠기를 고려한 새로운 주면 하중전이함수를 제안하였다. 제안된 하중전이함수는 기존 7본의 말뚝 재하시험 결과와 비교분석을 수행하였으며, 그 결과 본 제안식이 암반 굴착면의 거칠기 및 암반특성을 적절히 반영함을 알 수 있었다.

• 한국지반환경공학회 논문집
• /
• 제14권1호
• /
• pp.5-13
• /
• 2013

사질토 지반에 근입된 말뚝의 주변부에서는 말뚝의 수직하중에 의한 전단변형 시, 반경방향으로의 변위가 구속된다. 이러한 연직변위 구속상태에서의 전단강도는 기존의 직접전단실험으로는 모사하는데 어려움이 있다. 본 연구의 목적은 직접전단동안 연직변위를 허용하는 연직변위 허용조건(Free Normal Displacement: FND)의 직접전단실험과 연직변위를 허용하지 않는 연직변위 구속조건(Constrained Normal Displacement: CND)의 직접전단실험을 통하여 연직변위 구속여부가 전단강도에 미치는 영향을 평가 하는 것이다. 직접전단실험은 균등한 입도분포를 갖는 주문진 표준사를 사용하여, 연직변위의 구속여부에 따라 다양한 상대밀도와 초기응력조건 상태에서 수행되었다. 실험결과, CND 직접전단실험에서 얻은 전단강도는 FND 직접전단실험에서 얻은 전단강도보다 크게 나타났다. 또한, 상대밀도가 클수록 연직변위의 구속효과로 인한 전단강도의 증분이 더욱 늘어남을 보여주었다. 반면, 초기 연직응력의 증가는 구속효과로 인한 전단강도 증분의 감소로 나타나는 것을 관찰하였다. 본 연구에서는 경계부가 구속된 사질토지반의 안정성 평가 시, 전단강도에 대한 연직변위의 구속효과를 고려해야 함을 보여준다.

• Computers and Concrete
• /
• 제27권3호
• /
• pp.199-210
• /
• 2021

The aim of this paper was to examine the continuous and discontinuous contact problems between the functionally graded (FG) layer pressed with a uniformly distributed load and homogeneous half plane using an analytical method and FEM. The FG layer is made of non-homogeneous material with an isotropic stress-strain law with exponentially varying properties. It is assumed that the contact at the FG layer-half plane interface is frictionless, and only the normal tractions can be transmitted along the contacted regions. The body force of the FG layer is considered in the study. The FG layer was positioned on the homogeneous half plane without any bonds. Thus, if the external load was smaller than a certain critical value, the contact between the FG layer and half plane would be continuous. However, when the external load exceeded the critical value, there was a separation between the FG layer and half plane on the finite region, as discontinuous contact. Therefore, there have been some steps taken in this study. Firstly, an analytical solution for continuous and discontinuous contact cases of the problem has been realized using the theory of elasticity and Fourier integral transform techniques. Then, the problem modeled and two-dimensional analysis was carried out by using ANSYS package program based on FEM. Numerical results for initial separation distance and contact stress distributions between the FG layer and homogeneous half plane for continuous contact case; the start and end points of separation and contact stress distributions between the FG layer and homogeneous half plane for discontinuous contact case were provided for various dimensionless quantities including material inhomogeneity, distributed load width, the shear module ratio and load factor for both methods. The results obtained using FEM were compared with the results found using analytical formulation. It was found that the results obtained from analytical formulation were in perfect agreement with the FEM study.